Thinh Nguyen wrote: > Jun Li wrote: >> Hi >> >>> -----Original Message----- >>> From: Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx> >>> Sent: 2020年5月19日 14:46 >>> To: Jun Li <jun.li@xxxxxxx>; Felipe Balbi <balbi@xxxxxxxxxx>; Jun Li >>> <lijun.kernel@xxxxxxxxx> >>> Cc: John Stultz <john.stultz@xxxxxxxxxx>; lkml <linux-kernel@xxxxxxxxxxxxxxx>; Yu >>> Chen <chenyu56@xxxxxxxxxx>; Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>; Rob >>> Herring <robh+dt@xxxxxxxxxx>; Mark Rutland <mark.rutland@xxxxxxx>; ShuFan Lee >>> <shufan_lee@xxxxxxxxxxx>; Heikki Krogerus <heikki.krogerus@xxxxxxxxxxxxxxx>; >>> Suzuki K Poulose <suzuki.poulose@xxxxxxx>; Chunfeng Yun >>> <chunfeng.yun@xxxxxxxxxxxx>; Hans de Goede <hdegoede@xxxxxxxxxx>; Andy Shevchenko >>> <andy.shevchenko@xxxxxxxxx>; Valentin Schneider <valentin.schneider@xxxxxxx>; >>> Jack Pham <jackp@xxxxxxxxxxxxxx>; Linux USB List <linux-usb@xxxxxxxxxxxxxxx>; open >>> list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>; >>> Peter Chen <peter.chen@xxxxxxx> >>> Subject: Re: [PATCH v4 3/9] usb: dwc3: Increase timeout for CmdAct cleared by device >>> controller >>> >>> Thinh Nguyen wrote: >>>> Jun Li wrote: >>>>>> -----Original Message----- >>>>>> From: Felipe Balbi <balbif@xxxxxxxxx> On Behalf Of Felipe Balbi >>>>>> Sent: 2020年5月16日 19:57 >>>>>> To: Jun Li <jun.li@xxxxxxx>; Thinh Nguyen >>>>>> <Thinh.Nguyen@xxxxxxxxxxxx>; Jun Li <lijun.kernel@xxxxxxxxx> >>>>>> Cc: John Stultz <john.stultz@xxxxxxxxxx>; lkml >>>>>> <linux-kernel@xxxxxxxxxxxxxxx>; Yu Chen <chenyu56@xxxxxxxxxx>; Greg >>>>>> Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>; Rob Herring >>>>>> <robh+dt@xxxxxxxxxx>; Mark Rutland <mark.rutland@xxxxxxx>; ShuFan >>>>>> Lee <shufan_lee@xxxxxxxxxxx>; Heikki Krogerus >>>>>> <heikki.krogerus@xxxxxxxxxxxxxxx>; >>>>>> Suzuki K Poulose <suzuki.poulose@xxxxxxx>; Chunfeng Yun >>>>>> <chunfeng.yun@xxxxxxxxxxxx>; Hans de Goede <hdegoede@xxxxxxxxxx>; >>>>>> Andy Shevchenko <andy.shevchenko@xxxxxxxxx>; Valentin Schneider >>>>>> <valentin.schneider@xxxxxxx>; Jack Pham <jackp@xxxxxxxxxxxxxx>; >>>>>> Linux USB List <linux-usb@xxxxxxxxxxxxxxx>; open list:OPEN FIRMWARE >>>>>> AND FLATTENED DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>; >>>>>> Peter Chen <peter.chen@xxxxxxx>; Thinh Nguyen >>>>>> <Thinh.Nguyen@xxxxxxxxxxxx> >>>>>> Subject: RE: [PATCH v4 3/9] usb: dwc3: Increase timeout for CmdAct >>>>>> cleared by device controller >>>>>> >>>>>> >>>>>> Hi, >>>>>> >>>>>> Jun Li <jun.li@xxxxxxx> writes: >>>>>>>>>> Hi Thinh, could you comment this? >>>>>>>>> You only need to wake up the usb2 phy when issuing the command >>>>>>>>> while running in highspeed or below. If you're running in SS or >>>>>>>>> higher, internally the controller does it for you for usb3 phy. >>>>>>>>> In Jun's case, it seems like it takes longer for his phy to wake up. >>>>>>>>> >>>>>>>>> IMO, in this case, I think it's fine to increase the command timeout. >>>>>>>> Is there an upper limit to this? Is 32k clock the slowest that can >>>>>>>> be fed to the PHY as a suspend clock? >>>>>>> Yes, 32K clock is the slowest, Per DWC3 document on Power Down >>>>>>> Scale (bits 31:19 of GCTL): >>>>>>> >>>>>>> "Power Down Scale (PwrDnScale) >>>>>>> The USB3 suspend_clk input replaces pipe3_rx_pclk as a clock source >>>>>>> to a small part of the USB3 controller that operates when the SS >>>>>>> PHY is in its lowest power (P3) state, and therefore does not provide a clock. >>>>>>> The Power Down Scale field specifies how many suspend_clk periods >>>>>>> fit into a 16 kHz clock period. When performing the division, round >>>>>>> up the remainder. >>>>>>> For example, when using an 8-bit/16-bit/32-bit PHY and 25-MHz >>>>>>> Suspend clock, Power Down Scale = 25000 kHz/16 kHz = 13'd1563 >>>>>>> (rounder up) >>>>>>> Note: >>>>>>> - Minimum Suspend clock frequency is 32 kHz >>>>>>> - Maximum Suspend clock frequency is 125 MHz" >>>>>> Cool, now do we have an upper bound for how many clock cycles it >>>>>> takes to wake up the PHY? >>>>> My understanding is this ep command does not wake up the SS PHY, the >>>>> SS PHY still stays at P3 when execute this ep command. The time >>>>> required here is to wait controller complete something for this ep >>>>> command with 32K clock. >>>> Sorry I made a mistake. You're right. Just checked with one of the RTL >>>> engineers, and it doesn't need to wake up the phy. However, if it is >>>> eSS speed, it may take longer time as the command may be completing >>>> with the suspend clock. >>>> >>> What's the value for GCTL[7:6]? >> 2'b00 >> >> Thanks >> Li Jun > (Sorry for the delay reply) > > If it's 0, then the ram clock should be the same as the bus_clk, which > is odd since you mentioned that the suspend_clk is used instead while in P3. Just checked with the RTL engineer, even if GCTL[7:6] is set to 0, internally it can still run with suspend clock during P3. > Anyway, I was looking for a way maybe to improve the speed during > issuing a command. One way is to set GUSB3PIPECTL[17]=0, and it should > wakeup the phy anytime. I think Felipe suggested it. It's odd that it > doesn't work for you. I don't have other ideas beside increasing the > command timeout. > In any case, increasing the timeout should be fine with me. It maybe difficult to determine the max timeout base on the slowest clock rate and number of cycles. Different controller and controller versions behave differently and may have different number of clock cycles to complete a command. The RTL engineer recommended timeout to be at least 1ms (which maybe more than the polling rate of this patch). I'm fine with either the rate provided by this tested patch or higher. BR, Thinh
