Hi,
> -----Original Message-----
> From: Felipe Balbi <balbif@xxxxxxxxx> On Behalf Of Felipe Balbi
> Sent: 2020年5月16日 15:13
> To: Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx>; Jun Li <jun.li@xxxxxxx>; Jun Li
> <lijun.kernel@xxxxxxxxx>
> Cc: John Stultz <john.stultz@xxxxxxxxxx>; lkml <linux-kernel@xxxxxxxxxxxxxxx>; Yu
> Chen <chenyu56@xxxxxxxxxx>; Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>; Rob
> Herring <robh+dt@xxxxxxxxxx>; Mark Rutland <mark.rutland@xxxxxxx>; ShuFan Lee
> <shufan_lee@xxxxxxxxxxx>; Heikki Krogerus <heikki.krogerus@xxxxxxxxxxxxxxx>;
> Suzuki K Poulose <suzuki.poulose@xxxxxxx>; Chunfeng Yun
> <chunfeng.yun@xxxxxxxxxxxx>; Hans de Goede <hdegoede@xxxxxxxxxx>; Andy Shevchenko
> <andy.shevchenko@xxxxxxxxx>; Valentin Schneider <valentin.schneider@xxxxxxx>;
> Jack Pham <jackp@xxxxxxxxxxxxxx>; Linux USB List <linux-usb@xxxxxxxxxxxxxxx>; open
> list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>;
> Peter Chen <peter.chen@xxxxxxx>; Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx>
> Subject: Re: [PATCH v4 3/9] usb: dwc3: Increase timeout for CmdAct cleared by device
> controller
>
>
> Hi,
>
> Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx> writes:
> > Jun Li wrote:
> >>> -----Original Message-----
> >>> From: Felipe Balbi <balbif@xxxxxxxxx> On Behalf Of Felipe Balbi
> >>> Sent: 2020年5月15日 17:31
> >>> To: Jun Li <lijun.kernel@xxxxxxxxx>
> >>> Cc: John Stultz <john.stultz@xxxxxxxxxx>; lkml
> >>> <linux-kernel@xxxxxxxxxxxxxxx>; Yu Chen <chenyu56@xxxxxxxxxx>; Greg
> >>> Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>; Rob Herring
> >>> <robh+dt@xxxxxxxxxx>; Mark Rutland <mark.rutland@xxxxxxx>; ShuFan
> >>> Lee <shufan_lee@xxxxxxxxxxx>; Heikki Krogerus
> >>> <heikki.krogerus@xxxxxxxxxxxxxxx>;
> >>> Suzuki K Poulose <suzuki.poulose@xxxxxxx>; Chunfeng Yun
> >>> <chunfeng.yun@xxxxxxxxxxxx>; Hans de Goede <hdegoede@xxxxxxxxxx>;
> >>> Andy Shevchenko <andy.shevchenko@xxxxxxxxx>; Valentin Schneider
> >>> <valentin.schneider@xxxxxxx>; Jack Pham <jackp@xxxxxxxxxxxxxx>;
> >>> Linux USB List <linux-usb@xxxxxxxxxxxxxxx>; open list:OPEN FIRMWARE
> >>> AND FLATTENED DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>;
> >>> Peter Chen <peter.chen@xxxxxxx>; Jun Li <jun.li@xxxxxxx>; Thinh
> >>> Nguyen <Thinh.Nguyen@xxxxxxxxxxxx>
> >>> Subject: Re: [PATCH v4 3/9] usb: dwc3: Increase timeout for CmdAct
> >>> cleared by device controller
> >>>
> >>>
> >>> Hi,
> >>>
> >>> Jun Li <lijun.kernel@xxxxxxxxx> writes:
> >>>>> @@ -397,12 +407,18 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep
> >>>>> *dep, unsigned
> >>> cmd,
> >>>>> dwc3_gadget_ep_get_transfer_index(dep);
> >>>>> }
> >>>>>
> >>>>> - if (saved_config) {
> >>>>> + if (saved_hs_config) {
> >>>>> reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
> >>>>> - reg |= saved_config;
> >>>>> + reg |= saved_hs_config;
> >>>>> dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
> >>>>> }
> >>>>>
> >>>>> + if (saved_ss_config) {
> >>>>> + reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
> >>>>> + reg |= saved_ss_config;
> >>>>> + dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
> >>>>> + }
> >>>>> +
> >>>>> return ret;
> >>>>> }
> >>>> Unfortunately this way can't work, once the SS PHY enters P3,
> >>>> disable suspend_en can't force SS PHY exit P3, unless do this at
> >>>> the very beginning to prevent SS PHY entering P3(e.g. add
> >>>> "snps,dis_u3_susphy_quirk" for
> >>> test).
> >>>
> >>> It sounds like you have a quirky PHY.
> >> From what I got from the IC design, the behavior of
> >> DWC3_GUSB3PIPECTL_SUSPHY bit should be as what I said, not a quirky.
> >>
> >> Hi Thinh, could you comment this?
> >
> > You only need to wake up the usb2 phy when issuing the command while
> > running in highspeed or below. If you're running in SS or higher,
> > internally the controller does it for you for usb3 phy. In Jun's case,
> > it seems like it takes longer for his phy to wake up.
> >
> > IMO, in this case, I think it's fine to increase the command timeout.
>
> Is there an upper limit to this? Is 32k clock the slowest that can be fed to the
> PHY as a suspend clock?
Yes, 32K clock is the slowest, Per DWC3 document on Power Down Scale
(bits 31:19 of GCTL):
"Power Down Scale (PwrDnScale)
The USB3 suspend_clk input replaces pipe3_rx_pclk as a clock source
to a small part of the USB3 controller that operates when the SS PHY
is in its lowest power (P3) state, and therefore does not provide a clock.
The Power Down Scale field specifies how many suspend_clk periods
fit into a 16 kHz clock period. When performing the division, round up
the remainder.
For example, when using an 8-bit/16-bit/32-bit PHY and 25-MHz Suspend clock,
Power Down Scale = 25000 kHz/16 kHz = 13'd1563 (rounder up)
Note:
- Minimum Suspend clock frequency is 32 kHz
- Maximum Suspend clock frequency is 125 MHz"
Li Jun
>
> --
> balbi
