V1:
This series enables the Primary and Secondary USB controllers on the
QCS404, associated PHYs, role-switching and DTS descriptions.
The series takes in a number of patches worked on by a number of people
over the past few years from downstream, through to previous upstream
submissions for both of these interfaces. Additional work has been done to
enable USB role-switching.
1. USB SS
- extcon has been dropped in favour of gpio-usb-conn as discussed and
agreed previously by Jorge, Bjorn, Stephen Boyd and Jack Pham [1].
- Regulator API has been updated following suggestions from Bjorn.
- Sanitzation of the DT compatible name - dropped "snps" entirely
from the name - it made almost no sense to me and doesn't appear
consistent with similar naming conventions for Snopsys based IP.
2. USB HS
- Regulator API changes here.
- Dropped "snps" from the namespace for similar reasons as above.
- Dropped "28nm" from the namespace, looked superfluous.
- Changed "High-Speed" to "Hi-Speed".
- [2]
3. DWC3 Role switching
- At the time usb-gpio-conn was discussed it was mentioned that
role-switching was absent from the DWC3 driver.
- John Stultz has some patches in-flight for that, that I've included in
this series for completeness.
- Adds my SoB to relevant patches.
- Drops gerrit ChangeId.
4. DWC3 usb-gpio-conn
Needs to be a child node of the DWC3 driver so some code and DT binding
is required for that.
5. QCOM-DWC3
Since we are role-switching with an external PMIC supplying VBUS we want
to skip past toggling VBUS from QCOM-DWC3 controlled registers, so a
patch is added to the qcom-dwc3 driver to do that.
References:
1: USB SS PHY for Qualcomm's QCS404
https://lwn.net/ml/devicetree/20190207111734.24171-1-jorge.ramirez-ortiz@xxxxxxxxxx/
2: Add Synopsys High-Speed USB PHY driver for Qualcomm SoCs
https://lore.kernel.org/linux-arm-msm/20181127100722.9993-3-shawn.guo@xxxxxxxxxx/
https://www.spinics.net/lists/linux-usb/msg190003.html
V2:
- Fixes yaml error - Rob's YAML robot
- Exclusive control of reset in PHY drivers - Philipp Zabel
V3:
- Fixes typo generating YAML warning - Rob's YAML robot
V4:
https://lore.kernel.org/linux-arm-msm/20200122185610.131930-1-bryan.odonoghue@xxxxxxxxxx/
- Churn names of PHYs - Rob Herring
Rob questioned the name of the SuperSpeed PHY in V3.
Looking at available data
usb-hs-28nm - There are two possible PHYs on 28nm litho node
so it makes sense to name the PHY relating to its relevant
litho node.
usb-ss - This is not litho node dependent and is used on multiple SoCs
and litho nodes.
- Drop default mode for role switching - Felipe Balbi
Felipe asked if the default mode for role switching was
required and the answer is no. It makes no difference
becuase the USB ID pin ultimately dictates the mode of operation.
- Change "gpio_usb_connector" to "connector" - Rob
This was a minor change in terms of DTS but, means I need to look for the
DTS compatible string as opposed to a label given in the DTS.
No matter what the name of the label, this is he right thing to do.
- Used IS_ENABLED() - Felipe
The logic is the same but IS_ENABLED() is used now.
- Retained example of USB connector in dwc.txt - Rob, Felipe
Rob pointed out adding the connector was redundant as the documentation
already implies it.
Felipe seemed in favour of I think adding the example.
I've dropped the documentation of the connector and kept the example.
https://lore.kernel.org/linux-arm-msm/20200122185610.131930-7-bryan.odonoghue@xxxxxxxxxx/
- Added example of usb-role-switch in dwc3.txt - BOD
- Incorporated various inputs from Rob on DTS/YAML
- Added required:
- Added additionalProperties:
- Renamed "phy" clock to "ahb"
- maxItems dropped as indicated
Bjorn Andersson (1):
arm64: dts: qcom: qcs404: Add USB devices and PHYs
Bryan O'Donoghue (11):
dt-bindings: usb: dwc3: Add a gpio-usb-connector example
dt-bindings: usb: dwc3: Add a usb-role-switch to the example
usb: dwc3: qcom: Override VBUS when using gpio_usb_connector
usb: dwc3: Add support for usb-conn-gpio connectors
arm64: dts: qcom: qcs404-evb: Define VBUS detect pin
arm64: dts: qcom: qcs404-evb: Define VBUS boost pin
arm64: dts: qcom: qcs404-evb: Define USB ID pin
arm64: dts: qcom: qcs404-evb: Describe external VBUS regulator
arm64: dts: qcom: qcs404-evb: Raise vreg_l12_3p3 minimum voltage
arm64: dts: qcom: qcs404-evb: Enable secondary USB controller
arm64: dts: qcom: qcs404-evb: Enable primary USB controller
Jorge Ramirez-Ortiz (3):
dt-bindings: phy: remove qcom-dwc3-usb-phy
dt-bindings: Add Qualcomm USB SuperSpeed PHY bindings
phy: qualcomm: usb: Add SuperSpeed PHY driver
Shawn Guo (1):
phy: qualcomm: Add Synopsys 28nm Hi-Speed USB PHY driver
Sriharsha Allenki (1):
dt-bindings: phy: Add Qualcomm Synopsys Hi-Speed USB PHY binding
Yu Chen (1):
usb: dwc3: Registering a role switch in the DRD code.
.../bindings/phy/qcom,usb-hs-28nm.yaml | 90 ++++
.../devicetree/bindings/phy/qcom,usb-ss.yaml | 83 ++++
.../bindings/phy/qcom-dwc3-usb-phy.txt | 37 --
.../devicetree/bindings/usb/dwc3.txt | 9 +
arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 90 +++-
arch/arm64/boot/dts/qcom/qcs404.dtsi | 100 +++++
drivers/phy/qualcomm/Kconfig | 20 +
drivers/phy/qualcomm/Makefile | 2 +
drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c | 415 ++++++++++++++++++
drivers/phy/qualcomm/phy-qcom-usb-ss.c | 246 +++++++++++
drivers/usb/dwc3/core.h | 3 +
drivers/usb/dwc3/drd.c | 100 ++++-
drivers/usb/dwc3/dwc3-qcom.c | 22 +-
13 files changed, 1175 insertions(+), 42 deletions(-)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml
create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml
delete mode 100644 Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
create mode 100644 drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c
create mode 100644 drivers/phy/qualcomm/phy-qcom-usb-ss.c
--
2.25.0
