On 14-06-2019 03:02, Rob Herring wrote:
> On Thu, May 16, 2019 at 12:09:28PM +0530, Nagarjuna Kristam wrote:
>> Add device-tree binding documentation for the XUSB device mode controller
>> present on Tegra210 SoC. This controller supports the USB 3.0
>> specification.
>>
>> Signed-off-by: Nagarjuna Kristam <nkristam@xxxxxxxxxx>
>> ---
>> .../devicetree/bindings/usb/nvidia,tegra-xudc.txt | 101 +++++++++++++++++++++
>> 1 file changed, 101 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
>>
>> diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
>> new file mode 100644
>> index 0000000..d78b436
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
>> @@ -0,0 +1,101 @@
>> +Device tree binding for NVIDIA Tegra XUSB device mode controller (XUDC)
>> +=======================================================================
>> +
>> +The Tegra XUDC controller supports both USB 2.0 HighSpeed/FullSpeed and
>> +USB 3.0 SuperSpeed protocols.
>> +
>> +Required properties:
>> +--------------------
>> +- compatible: For Tegra210, must contain "nvidia,tegra210-xudc".
>> +- reg: Must contain the base and length of the XUSB device registers, XUSB device
>> + PCI Config registers and XUSB device controller registers.
>> +- interrupts: Must contain the XUSB device interrupt.
>> +- clocks: Must contain an entry for all clocks used.
>> + See ../clock/clock-bindings.txt for details.
>> +- clock-names: Must include the following entries:
>> + - dev: Clock to enable core XUSB dev clock.
>> + - ss: Clock to enable XUSB super speed clock.
>> + - ss_src: Clock to enable XUSB super speed dev clock.
>> + - hs_src: Clock to enable XUSB high Speed dev clock.
>> + - fs_src: Clock to enable XUSB full Speed dev clock.
>> +- nvidia,xusb-padctl: phandle to the XUSB pad controller that is used to
>> + configure the USB pads used by the XUDC controller.
>> +- power-domains: A list of PM domain specifiers that reference each power-domain
>> + used by the XUSB device mode controller. This list must comprise of a specifier
>> + for the XUSBA and XUSBB power-domains. See ../power/power_domain.txt and
>> + ../arm/tegra/nvidia,tegra20-pmc.txt for details.
>> +- power-domain-names: A list of names that represent each of the specifiers in
>> + the 'power-domains' property. Must include 'ss' and 'dev'.
>> +
>> +For Tegra210:
>> +- avddio-usb-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V.
>
> Wouldn't an analog supply belong in the phy node?
>
This is USB controller power supply and hence added it part of controller driver node.
Will correct documentation accordingly.
>> +- hvdd-usb-supply: USB controller power supply. Must supply 3.3 V.
>> +
>> +- phys: Must contain an entry for each entry in phy-names.
>> + See ../phy/phy-bindings.txt for details.
>> +- phy-names: Should include an entry for each PHY used by the controller.
>> + Names must be "usb2", and "usb3" if support SuperSpeed device mode.
>> + - "usb3" phy, SuperSpeed (SSTX+/SSTX-/SSRX+/SSRX-) data lines.
>> + - "usb2" phy, USB 2.0 (D+/D-) data lines.
>> +
>> +- extcon: Must contains an extcon entry which detects USB VBUS pin.
>> + See ../extcon/extcon-usb-gpio.txt for details.
>
> Use the usb-connector binding for new bindings.
>
already taken care in V4 series of this patch.
Thanks,
Nagarjuna
>> +
>> +Example:
>> +--------
>> + pmc: pmc@7000e400 {
>> + compatible = "nvidia,tegra210-pmc";
>> + reg = <0x0 0x7000e400 0x0 0x400>;
>> + clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
>> + clock-names = "pclk", "clk32k_in";
>> +
>> + powergates {
>> + pd_xusbss: xusba {
>> + clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>;
>> + resets = <&tegra_car TEGRA210_CLK_XUSB_SS>;
>> + #power-domain-cells = <0>;
>> + };
>> +
>> + pd_xusbdev: xusbb {
>> + clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>;
>> + resets = <&tegra_car 95>;
>> + #power-domain-cells = <0>;
>> + };
>> + };
>> + };
>> +
>> + xudc@700d0000 {
>> + compatible = "nvidia,tegra210-xudc";
>> + reg = <0x0 0x700d0000 0x0 0x8000>,
>> + <0x0 0x700d8000 0x0 0x1000>,
>> + <0x0 0x700d9000 0x0 0x1000>;
>> +
>> + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>,
>> + <&tegra_car TEGRA210_CLK_XUSB_SS>,
>> + <&tegra_car TEGRA210_CLK_XUSB_SSP_SRC>,
>> + <&tegra_car TEGRA210_CLK_XUSB_HS_SRC>,
>> + <&tegra_car TEGRA210_CLK_XUSB_FS_SRC>;
>> + clock-names = "dev", "ss", "ss_src",
>> + "hs_src", "fs_src";
>> +
>> + power-domains = <&pd_xusbdev>, <&pd_xusbss>;
>> + power-domain-names = "dev", "ss";
>> +
>> + nvidia,xusb-padctl = <&padctl>;
>> +
>> + phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>;
>> + phy-names = "usb2;
>> +
>> + avddio-usb-supply = <&vdd_pex_1v05>;
>> + hvdd-usb-supply = <&vdd_3v3_sys>;
>> +
>> + extcon = <&extcon_usb>;
>> + };
>> +
>> + extcon_usb: extcon_vbus {
>> + compatible = "linux,extcon-usb-gpio";
>> + vbus-gpio = <&gpio TEGRA_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
>> + };
>> +
>> --
>> 2.7.4
>>
