Hi Greg, Felipe, Minas, Gentle ping about these remaining patches, who is supposed to pick them ? Thanks, Neil On 25/03/2019 10:39, Neil Armstrong wrote: > This patchset adds support for USB on Amlogic G12A SoCs. > > This patchset is composed with : > - bindings of the PHYs > - bindings of the USB Control Glue > - PHY Drivers > - USB Control Glue driver > > Device Tree nodes will be added in a separate patchset. > > The Amlogic G12A USB Complex is composed of : > - 2 USB Controllers : > * DWC3 for USB2 and USB3 Host functionality > * DWC2 for USB2 Peripheral functionality > - 2 USB2 OTG PHYs, only a single one will be routed to either DWC2 to DWC3 > - 1 USB3 PHY shared with PCIE funcionnality > - A Glue to control PHY routing, setup and OTG detection > > The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including > routing of the OTG PHY between the DWC3 and DWC2 controllers, and > setups the on-chip OTG mode selection for this PHY. > > This drivers supports the on-probe setup of the OTG mode, and manually > via the USB Role interface. The IRQ mode change detect is yet to be added > in a future patchset, mainly due to lack of hardware to validate on. > > Changes since v4 at [3]: > - remove remaining phy_put/clk_put() of patch 8 > - handled phy_power_off/on() in suspend/resume > - Collected review tag on patch 8 > > Changes since v3 at [2]: > - Documented and replaced magic values in USB2 PHY driver > > Changes since v2 at [1]: > - Collected review tags > - Removed syscon.h in usb2 phy driver > - Added comment on the USB3/PCIe switch > - Renamed dwc3_meson_g12a_usb_init_mode in glue driver > - Changed indentation in dwc3_meson_g12a_role_set > - Switched to of_get_compatible_child in glue code > - Added devm_add_action_or_reset() to disable clock in case of probe failure > - Checks priv->vbus before enabling regulator > - Switched phy_init/phy_power_on > - Removed priv->phys[i] NULL checks in suspend code > - Removed clk_disable_unprepare/clk_put in remove code > > Changes since v1 at [0]: > - USB2 PHY Bindings: collected tags and updated commit log > - USB3/PCIE PHY Bindings: collected tag and updated reset list > - DWC2 Compatible: collected tags > - DWC3 Glue Bindings: > - removed clock-names and reset-names for single entries > - removed ports graph for PHYs and replaced by phys list with phy-names > - added dr_mode and optional vbus-supply > - fixed example > - USB2 PHY Driver: removed USB_SUPPORT and otg.h include > - USB3/PCIE PHY Driver: removed USB_SUPPORT, fixed comment and unused reg variable > - USB Glue Driver: > - Moved debugfs I/F to USB_ROLE_SWITCH framework > - Integrated USB Glue Control Registers offset > - Removed of graph parsing to use devm_phy_optional_get() > - Fixed PHY mode handling and OTG switching > - Simplified PHY calls by removing the NULL test > - Added optional vbus regulator handling > > [1] https://lkml.kernel.org/r/20190212151413.24632-1-narmstrong@xxxxxxxxxxxx > [2] https://lkml.kernel.org/r/20190304103846.2060-1-narmstrong@xxxxxxxxxxxx > [3] https://lkml.kernel.org/r/20190318101153.7531-1-narmstrong@xxxxxxxxxxxx > [4] https://lkml.kernel.org/r/20190318132655.30040-1-narmstrong@xxxxxxxxxxxx > > Neil Armstrong (8): > dt-bindings: phy: Add Amlogic G12A USB2 PHY Bindings > dt-bindings: phy: Add Amlogic G12A USB3+PCIE Combo PHY Bindings > dt-bindings: usb: dwc2: Add Amlogic G12A DWC2 Compatible > dt-bindings: usb: dwc3: Add Amlogic G12A DWC3 Glue Bindings > phy: amlogic: add Amlogic G12A USB2 PHY Driver > phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo PHY Driver > usb: dwc2: Add Amlogic G12A DWC2 Params > usb: dwc3: Add Amlogic G12A DWC3 glue > > .../bindings/phy/meson-g12a-usb2-phy.txt | 22 + > .../bindings/phy/meson-g12a-usb3-pcie-phy.txt | 22 + > .../devicetree/bindings/usb/amlogic,dwc3.txt | 88 +++ > .../devicetree/bindings/usb/dwc2.txt | 1 + > drivers/phy/amlogic/Kconfig | 22 + > drivers/phy/amlogic/Makefile | 2 + > drivers/phy/amlogic/phy-meson-g12a-usb2.c | 341 ++++++++++ > .../phy/amlogic/phy-meson-g12a-usb3-pcie.c | 413 ++++++++++++ > drivers/usb/dwc2/params.c | 12 + > drivers/usb/dwc3/Kconfig | 10 + > drivers/usb/dwc3/Makefile | 1 + > drivers/usb/dwc3/dwc3-meson-g12a.c | 604 ++++++++++++++++++ > 12 files changed, 1538 insertions(+) > create mode 100644 Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt > create mode 100644 Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt > create mode 100644 drivers/phy/amlogic/phy-meson-g12a-usb2.c > create mode 100644 drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c > create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c >
