Hi Rob,
On 05/08/2018 01:09 AM, Rob Herring wrote:
On Sat, May 05, 2018 at 06:09:49PM +0800, sunjg79@xxxxxxx wrote:
From: Jianguo Sun <sunjianguo1@xxxxxxxxxx>
This commit adds bindings doc for HiSilicon STB xHCI host controller.
Signed-off-by: Jianguo Sun <sunjianguo1@xxxxxxxxxx>
---
.../bindings/usb/hisilicon,histb-xhci.txt | 46 ++++++++++++++++++++++
1 file changed, 46 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt
diff --git a/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt
new file mode 100644
index 0000000..b1a06f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt
@@ -0,0 +1,46 @@
+HiSilicon STB xHCI
+
+The device node for HiSilicon STB xHCI host controller
+
+Required properties:
+ - compatible: should be "hisilicon,hi3798cv200-xhci"
+ - reg: specifies physical base address and size of the registers
+ - interrupts : interrupt used by the controller
+ - clocks: a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+ - clock-names: must contain
+ "bus": for bus clock
+ "utmi": for utmi clock
+ "pipe": for pipeE clock
+ "suspend": for suspend clock
+ - resets: a list of phandle and reset specifier pairs as listed in
+ reset-names property.
+ - reset-names: must contain
+ "soft": for soft reset
+ - phys: a list of phandle + phy specifier pairs
+ - phy-names: must contain at least one of following:
+ "inno": for inno phy
+ "combo": for combo phy
+
+Optional properties:
+ - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
+ - usb3-lpm-capable: determines if platform is USB3 LPM capable
+ - quirk-broken-port-ped: set if the controller has broken port disable mechanism
This should either be true or not based on the compatible string.
This is borrowed from usb-xhci.txt, and I wasn't aware that it was a
workaround.
Since this issue doesn't occur on Hi3798CV200 SoC, I will remove this
property in v3.
Thanks.
+ - imod-interval-ns: default interrupt moderation interval is 40000ns
+
+Example:
+
+xhci0: xchi@f98a0000 {
+ compatible = "hisilicon,hi3798cv200-xhci";
+ reg = <0xf98a0000 0x10000>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HISTB_USB3_BUS_CLK>,
+ <&crg HISTB_USB3_UTMI_CLK>,
+ <&crg HISTB_USB3_PIPE_CLK>,
+ <&crg HISTB_USB3_SUSPEND_CLK>;
+ clock-names = "bus", "utmi", "pipe", "suspend";
+ resets = <&crg 0xb0 12>;
+ reset-names = "soft";
+ phys = <&usb2_phy1_port1 0>, <&combphy0 PHY_TYPE_USB3>;
+ phy-names = "inno", "combo";
+};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
