On Sat, May 05, 2018 at 06:09:49PM +0800, sunjg79@xxxxxxx wrote:
> From: Jianguo Sun <sunjianguo1@xxxxxxxxxx>
>
> This commit adds bindings doc for HiSilicon STB xHCI host controller.
>
> Signed-off-by: Jianguo Sun <sunjianguo1@xxxxxxxxxx>
> ---
> .../bindings/usb/hisilicon,histb-xhci.txt | 46 ++++++++++++++++++++++
> 1 file changed, 46 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt
>
> diff --git a/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt
> new file mode 100644
> index 0000000..b1a06f1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt
> @@ -0,0 +1,46 @@
> +HiSilicon STB xHCI
> +
> +The device node for HiSilicon STB xHCI host controller
> +
> +Required properties:
> + - compatible: should be "hisilicon,hi3798cv200-xhci"
> + - reg: specifies physical base address and size of the registers
> + - interrupts : interrupt used by the controller
> + - clocks: a list of phandle + clock-specifier pairs, one for each
> + entry in clock-names
> + - clock-names: must contain
> + "bus": for bus clock
> + "utmi": for utmi clock
> + "pipe": for pipeE clock
> + "suspend": for suspend clock
> + - resets: a list of phandle and reset specifier pairs as listed in
> + reset-names property.
> + - reset-names: must contain
> + "soft": for soft reset
> + - phys: a list of phandle + phy specifier pairs
> + - phy-names: must contain at least one of following:
> + "inno": for inno phy
> + "combo": for combo phy
> +
> +Optional properties:
> + - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
> + - usb3-lpm-capable: determines if platform is USB3 LPM capable
> + - quirk-broken-port-ped: set if the controller has broken port disable mechanism
This should either be true or not based on the compatible string.
> + - imod-interval-ns: default interrupt moderation interval is 40000ns
> +
> +Example:
> +
> +xhci0: xchi@f98a0000 {
> + compatible = "hisilicon,hi3798cv200-xhci";
> + reg = <0xf98a0000 0x10000>;
> + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&crg HISTB_USB3_BUS_CLK>,
> + <&crg HISTB_USB3_UTMI_CLK>,
> + <&crg HISTB_USB3_PIPE_CLK>,
> + <&crg HISTB_USB3_SUSPEND_CLK>;
> + clock-names = "bus", "utmi", "pipe", "suspend";
> + resets = <&crg 0xb0 12>;
> + reset-names = "soft";
> + phys = <&usb2_phy1_port1 0>, <&combphy0 PHY_TYPE_USB3>;
> + phy-names = "inno", "combo";
> +};
> --
> 2.7.4
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
