Hi > -----Original Message----- > From: Mats Karrman [mailto:mats.dev.list@xxxxxxxxx] > Sent: 2018年3月30日 3:54 > To: Jun Li <jun.li@xxxxxxx>; robh+dt@xxxxxxxxxx; gregkh@xxxxxxxxxxxxxxxxxxx; > heikki.krogerus@xxxxxxxxxxxxxxx; linux@xxxxxxxxxxxx > Cc: a.hajda@xxxxxxxxxxx; shufan_lee@xxxxxxxxxxx; Peter Chen > <peter.chen@xxxxxxx>; devicetree@xxxxxxxxxxxxxxx; > linux-usb@xxxxxxxxxxxxxxx; dl-linux-imx <linux-imx@xxxxxxx>; > devel@xxxxxxxxxxxxxxxxxxxx > Subject: Re: [PATCH v4 01/13] dt-bindings: connector: add properties for typec > > Hi Li, > > On 03/28/2018 06:06 PM, Li Jun wrote: > > > Add bingdings supported by current typec driver, so user can pass all > > those properties via dt. > > > > Signed-off-by: Li Jun <jun.li@xxxxxxx> > > --- > > .../bindings/connector/usb-connector.txt | 39 > ++++++++++++++++++++++ > > 1 file changed, 39 insertions(+) > > > > diff --git > > a/Documentation/devicetree/bindings/connector/usb-connector.txt > > b/Documentation/devicetree/bindings/connector/usb-connector.txt > > index e1463f1..922f22b 100644 > > --- a/Documentation/devicetree/bindings/connector/usb-connector.txt > > +++ b/Documentation/devicetree/bindings/connector/usb-connector.txt > > @@ -15,6 +15,29 @@ Optional properties: > > - type: size of the connector, should be specified in case of USB-A, USB-B > > non-fullsize connectors: "mini", "micro". > > > > +Optional properties for usb-c-connector: > > +- power-type: should be one of "source", "sink" or "dual"(DRP) if > > +typec > > + connector has power support. > > +- try-power-role: preferred power role if "dual"(DRP) can support > > +Try.SNK > > + or Try.SRC, should be "sink" for Try.SNK or "source" for Try.SRC. > > +- data-type: should be one of "host", "device", "dual"(DRD) if typec > > + connector supports USB data. > > + > > +Required properties for usb-c-connector with power delivery support: > > +- source-pdos: An array of u32 with each entry providing supported > > +power > > + source data object(PDO), the detailed bit definitions of PDO can be > > +found > > + in "Universal Serial Bus Power Delivery Specification" chapter > > +6.4.1.2 > > + Source_Capabilities Message, the order of each entry(PDO) should > > +follow > > + the PD spec chapter 6.4.1. Required for power source and power dual role. > > +- sink-pdos: An array of u32 with each entry providing supported > > +power > > + sink data object(PDO), the detailed bit definitions of PDO can be > > +found > > + in "Universal Serial Bus Power Delivery Specification" chapter > > +6.4.1.3 > > + Sink Capabilities Message, the order of each entry(PDO) should > > +follow > > + the PD spec chapter 6.4.1. Required for power sink and power dual role. > > +- op-sink-microwatt-hours: Sink required operating power in micro > > + watt-hours, if source offered power is less then it, Capability > > +Mismatch > > + is set, required for power sink and power dual role. > > This doesn't make sense. The unit of power is watt (W), watt-hour on the other > hand is a measurement of energy. I think "op-sink-microwatt" is what we want > here. Yes, you are right, microwatt is what I should use here. I will change. Li Jun > > // Mats > > > + > > Required nodes: > > - any data bus to the connector should be modeled using the OF graph > bindings > > specified in bindings/graph.txt, unless the bus is between parent > > node and @@ -73,3 +96,19 @@ ccic: s2mm005@33 { > > }; > > }; > > }; > > + > > +3. USB-C connector attached to a typec port controller(ptn5110), > > +which has power delivery support and enables drp. > > + > > +typec: ptn5110@50 { > > + ... > > + usb_con: connector { > > + compatible = "usb-c-connector"; > > + label = "USB-C"; > > + power-type = "dual"; > > + try-power-role = "sink"; > > + source-pdos = <0x380190c8>; > > + sink-pdos = <0x380190c8 0x3802d0c8>; > > + op-sink-microwatt-hours = <9000000>; > > + }; > > +}; > > ��.n��������+%������w��{.n�����{���)�� jg��� �����ݢj����G���� ���j:+v���w�m������w�������h�����٥
