On Sat, Feb 17, 2018 at 01:07:23PM -0800, Tony Lindgren wrote:
> Let's add support for the GPIO controlled USB PHY on the MDM6600 modem.
> It is used on some Motorola Mapphone series of phones and tablets such
> as Droid 4.
>
> The MDM6600 is hardwired to the first OHCI port in the Droid 4 case, and
> is controlled by several GPIOs. The USB PHY is integrated into the MDM6600
> device it seems. We know this as we get L3 errors from omap-usb-host if
> trying to use the PHY before MDM6600 is configured.
>
> The GPIOs controlling MDM6600 are used to power MDM660 on and off, to
MDM660 a typo?
> configure the USB start-up mode (normal mode versus USB flashing), and
> they also tell the state of the MDM6600 device.
>
> The two start-up mode GPIOs are dual-purposed and used for out of band
> (OOB) wake-up for USB and TS 27.010 serial mux. But we need to configure
> the USB start-up mode first to get MDM6600 booted in the right mode to
> be usable in the first place.
>
> For now, this driver just gives up the two start-up mode GPIOs after the
> modem has been configured to boot in normal mode. One of them we may
> want to configure for USB OOB wake in this driver later on, but that's a
> separate series of patches and needs more work.
>
> Note that the Motorola Mapphone Linux kernel tree has a "radio-ctrl"
> driver for modems. But it really does not control the radio at all, it
> just controls the modem power and start-up mode for USB. So I came to
> the conclusion that we're better off having this done in the USB PHY
> driver. For adding support for USB flashing mode, we can later on add
> a kernel module option for flash_mode=1 or something similar.
>
> Also note that currently there is no PM runtime support for the OHCI
> on omap variant SoCs. So for low(er) power idle states, currenty both
> ohci-platform and phy-mapphone-mdm6600 must be unloaded or unbound.
>
> For reference here is what I measured for total power consumption on
> an idle Droid 4 with and without USB related MDM6600 modules:
>
> idle lcd off phy-mapphone-mdm6600 ohci-platform
> 153mW 284mW 344mW
>
> So it seems that MDM6600 is currently not yet idling even with it's
> radio turned off, but that's something that is beyond the control of
> this USB PHY driver.
>
> Cc: devicetree@xxxxxxxxxxxxxxx
> Cc: Mark Rutland <mark.rutland@xxxxxxx>
> Cc: Marcel Partap <mpartap@xxxxxxx>
> Cc: Michael Scott <michael.scott@xxxxxxxxxx>
> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> Cc: Sebastian Reichel <sre@xxxxxxxxxx>
> Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
> ---
> .../bindings/phy/phy-mapphone-mdm6600.txt | 30 ++
> drivers/phy/motorola/Kconfig | 9 +
> drivers/phy/motorola/Makefile | 1 +
> drivers/phy/motorola/phy-mapphone-mdm6600.c | 490 +++++++++++++++++++++
> 4 files changed, 530 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt
> create mode 100644 drivers/phy/motorola/phy-mapphone-mdm6600.c
>
> diff --git a/Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt b/Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt
> new file mode 100644
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt
> @@ -0,0 +1,30 @@
> +Device tree binding documentation for Motorola Mapphone MDM6600 USB PHY
> +
> +Required properties:
> +- compatible Must be "motorola,mapphone-mdm6600"
> +- enable-gpios GPIO to enable the USB PHY
> +- power-gpios GPIO to power on the device
> +- reset-gpios GPIO to reset the device
The are pretty standard, but...
> +- mode-gpios Two GPIOs to configure MDM6600 USB start-up mode for
> + normal mode versus USB flashing mode
> +- status-gpios Three GPIOs to read the power state of the MDM6600
> +- cmd-gpios Three GPIOs to control the power state of the MDM6600
These 3 should have vendor a prefix.
> +
> +Example:
> +
> +fsusb1_phy: fsusb1_phy {
usb-phy {
> + compatible = "motorola,mapphone-mdm6600";
> + enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>; /* gpio_95 */
> + power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54 */
> + reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>; /* gpio_49 */
> + mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>, /* gpio_148 */
> + <&gpio5 21 GPIO_ACTIVE_HIGH>; /* gpio_149 */
> + status-gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>, /* gpio_55 */
> + <&gpio2 21 GPIO_ACTIVE_HIGH>, /* gpio_53 */
> + <&gpio2 20 GPIO_ACTIVE_HIGH>; /* gpio_52 */
> + cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>, /* gpio_103 */
> + <&gpio4 8 GPIO_ACTIVE_HIGH>, /* gpio_104 */
> + <&gpio5 14 GPIO_ACTIVE_HIGH>; /* gpio_142 */
> + #phy-cells = <0>;
> +};
> +
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
