Problem summary:
Out of the box, a USB 3.0 SATA 6.0 enclosure, hangs during reads or
writes and spits out some errors, when directly connected to a
computer's USB port. When connected via a USB hub, uas is still used,
but the errors do not occur. When setting a quirk to blacklist the
drive from uas, the problem doesn't happen when directly connected
either.
Host:
Intel ® NUC Board NUC5PPYB
kernel 4.14.18-300.fc27.x86_64
Fedora 27
One 1.5A port
Multiple 900 mA ports
lspci -vvnn
00:14.0 USB controller [0c03]: Intel Corporation Atom/Celeron/Pentium
Processor x5-E8000/J3xxx/N3xxx Series USB xHCI Controller [8086:22b5]
(rev 21) (prog-if 30 [XHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 116
Region 0: Memory at 81400000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee0300c Data: 4122
Kernel driver in use: xhci_hcd
Enclosure:
$ sudo lsusb -v
Bus 002 Device 003: ID 152d:0567 JMicron Technology Corp. / JMicron
USA Technology Corp. JMS567 SATA 6Gb/s bridge
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x152d JMicron Technology Corp. / JMicron USA
Technology Corp.
idProduct 0x0567 JMS567 SATA 6Gb/s bridge
bcdDevice 7.01
iManufacturer 1 JMicron
iProduct 2 USB3.0 Device
iSerial 3 DB98765433E84
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 121
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 896mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 4
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 98
iInterface 10 MSC USB Attached SCSI
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Command pipe (0x01)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
MaxStreams 32
Status pipe (0x02)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
MaxStreams 32
Data-in pipe (0x03)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 7
MaxStreams 32
Data-out pipe (0x04)
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000f0e
BESL Link Power Management (LPM) Supported
BESL value 3840 us
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 32 micro seconds
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x000c
(Bus Powered)
U1 Enabled
U2 Enabled
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 4.14
iManufacturer 3 Linux 4.14.18-300.fc27.x86_64 xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:14.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 31
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
bMaxBurst 0
Hub Descriptor:
bLength 12
bDescriptorType 42
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
bHubDecLat 0.0 micro seconds
wHubDelay 0 nano seconds
DeviceRemovable 0x60
Hub Port Status:
Port 1: 0000.02a0 5Gbps power Rx.Detect
Port 2: 0000.0203 5Gbps power U0 enable connect
Port 3: 0000.02a0 5Gbps power Rx.Detect
Port 4: 0000.02a0 5Gbps power Rx.Detect
Port 5: 0000.02a0 5Gbps power Rx.Detect
Port 6: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 15
bNumDeviceCaps 1
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x02
Latency Tolerance Messages (LTM) Supported
wSpeedsSupported 0x0008
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 3
Lowest fully-functional device speed is SuperSpeed (5Gbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 512 micro seconds
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
Bus 001 Device 004: ID 8087:0a2a Intel Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 224 Wireless
bDeviceSubClass 1 Radio Frequency
bDeviceProtocol 1 Bluetooth
bMaxPacketSize0 64
idVendor 0x8087 Intel Corp.
idProduct 0x0a2a
bcdDevice 0.01
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 177
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0000 1x 0 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0000 1x 0 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 1
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0009 1x 9 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0009 1x 9 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 2
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0011 1x 17 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0011 1x 17 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 3
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0019 1x 25 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0019 1x 25 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 4
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0021 1x 33 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0021 1x 33 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 5
bNumEndpoints 2
bInterfaceClass 224 Wireless
bInterfaceSubClass 1 Radio Frequency
bInterfaceProtocol 1 Bluetooth
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0031 1x 49 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0031 1x 49 bytes
bInterval 1
can't get device qualifier: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
Bus 001 Device 003: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 2 TT per port
bMaxPacketSize0 64
idVendor 0x05e3 Genesys Logic, Inc.
idProduct 0x0610 4-port hub
bcdDevice 32.98
iManufacturer 0
iProduct 1 USB2.0 Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 41
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 1 Single TT
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 2 TT per port
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x00e9
Per-port power switching
Per-port overcurrent protection
TT think time 32 FS bits
Port indicators
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 100 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
bNumConfigurations 1
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.14
iManufacturer 3 Linux 4.14.18-300.fc27.x86_64 xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:14.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 7
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0xc0
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0503 highspeed power enable connect
Port 6: 0000.0100 power
Port 7: 0000.0100 power
can't get device qualifier: Resource temporarily unavailable
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
[chris@f27s ~]$
Annotated kernel messages:
Directly connect the enclosure to the 1.5A USB 3.0 port on the computer.
[61365.874627] usb 2-2: new SuperSpeed USB device number 2 using xhci_hcd
[61365.888928] usb 2-2: New USB device found, idVendor=152d, idProduct=0567
[61365.888966] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[61365.888994] usb 2-2: Product: USB3.0 Device
[61365.889010] usb 2-2: Manufacturer: JMicron
[61365.889023] usb 2-2: SerialNumber: DB98765433E84
[61366.214438] usbcore: registered new interface driver usb-storage
[61366.225134] scsi host2: uas
[61366.225490] usbcore: registered new interface driver uas
[61368.402082] scsi 2:0:0:0: Direct-Access TOSHIBA MQ01ABD100
0701 PQ: 0 ANSI: 6
[61369.176275] xhci_hcd 0000:00:14.0: Cannot set link state.
[61369.176296] usb usb2-port2: cannot disable (err = -32)
[61369.176306] usb 2-2: USB disconnect, device number 2
[61369.176538] scsi 2:0:0:0: tag#0 uas_zap_pending 0 uas-tag 1 inflight: CMD
[61369.176549] scsi 2:0:0:0: tag#0 CDB: Inquiry 12 01 00 00 ff 00
[61369.274383] sd 2:0:0:0: Attached scsi generic sg1 type 0
[61369.434695] sd 2:0:0:0: [sdb] Read Capacity(16) failed: Result:
hostbyte=DID_ERROR driverbyte=DRIVER_OK
[61369.434739] sd 2:0:0:0: [sdb] Sense not available.
[61369.554847] sd 2:0:0:0: [sdb] Read Capacity(10) failed: Result:
hostbyte=DID_ERROR driverbyte=DRIVER_OK
[61369.554891] sd 2:0:0:0: [sdb] Sense not available.
[61369.602836] sd 2:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[61369.602874] sd 2:0:0:0: [sdb] 0-byte physical blocks
[61369.642581] sd 2:0:0:0: [sdb] Write Protect is off
[61369.642619] sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
[61369.683573] sd 2:0:0:0: [sdb] Asking for cache data failed
[61369.683611] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[61369.869846] sd 2:0:0:0: [sdb] Read Capacity(16) failed: Result:
hostbyte=DID_ERROR driverbyte=DRIVER_OK
[61369.869892] sd 2:0:0:0: [sdb] Sense not available.
[61369.989567] sd 2:0:0:0: [sdb] Read Capacity(10) failed: Result:
hostbyte=DID_ERROR driverbyte=DRIVER_OK
[61369.989615] sd 2:0:0:0: [sdb] Sense not available.
[61370.141558] sd 2:0:0:0: [sdb] Attached SCSI disk
[61371.674597] usb 2-2: new SuperSpeed USB device number 3 using xhci_hcd
[61371.688759] usb 2-2: New USB device found, idVendor=152d, idProduct=0567
[61371.688801] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[61371.688829] usb 2-2: Product: USB3.0 Device
[61371.688852] usb 2-2: Manufacturer: JMicron
[61371.688872] usb 2-2: SerialNumber: DB98765433E84
[61371.696500] scsi host2: uas
[61371.697653] scsi 2:0:0:0: Direct-Access TOSHIBA MQ01ABD100
0701 PQ: 0 ANSI: 6
[61371.699076] sd 2:0:0:0: Attached scsi generic sg1 type 0
[61371.699501] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks:
(1.00 TB/932 GiB)
[61371.699516] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[61371.699705] sd 2:0:0:0: [sdb] Write Protect is off
[61371.699713] sd 2:0:0:0: [sdb] Mode Sense: 5f 00 00 08
[61371.700137] sd 2:0:0:0: [sdb] Disabling FUA
[61371.700147] sd 2:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[61371.783958] sdb: sdb1
[61371.786899] sd 2:0:0:0: [sdb] Attached SCSI disk
[chris@f27s ~]$
sudo cryptsetup open
[63077.497429] device-mapper: table: 253:9: adding target device sdb1
caused an alignment inconsistency: physical_block_size=4096,
logical_block_size=512, alignment_offset=0, start=2097152
[63077.497484] device-mapper: table: 253:9: adding target device sdb1
caused an alignment inconsistency: physical_block_size=4096,
logical_block_size=512, alignment_offset=0, start=2097152
[63079.671918] device-mapper: thin: Data device (dm-11) discard
unsupported: Disabling discard passdown.
sudo mount
[63126.445367] SGI XFS with ACLs, security attributes, no debug enabled
[63126.461972] XFS (dm-14): Mounting V5 Filesystem
[63127.084290] XFS (dm-14): Ending clean mount
Start a copy (cp) with this volume as the source for reading, works
for a short while at normal speeds, but then within a few seconds,
throughput stops entirely per iotop, and only one kernel message:
[63246.094062] xhci_hcd 0000:00:14.0: ERROR Unknown event condition 10
for slot 6 ep 6 , HC probably busted
During this gap the access LED on the enclosure is flashing but
there's no throughput for the copy, and no user space or kernel
errors. I cancel the copy and then the following is found in dmesg:
[63276.943798] sd 2:0:0:0: [sdb] tag#0 uas_eh_abort_handler 0 uas-tag
1 inflight: CMD IN
[63276.943826] sd 2:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 43 ae 7a 08
00 02 00 00
[63276.944040] xhci_hcd 0000:00:14.0: WARN Set TR Deq Ptr cmd failed
due to incorrect slot or ep state.
[63276.944163] sd 2:0:0:0: [sdb] tag#1 uas_eh_abort_handler 0 uas-tag
2 inflight: CMD IN
[63276.944198] sd 2:0:0:0: [sdb] tag#1 CDB: Read(10) 28 00 43 ae 78 08
00 02 00 00
[63276.944283] xhci_hcd 0000:00:14.0: WARN Set TR Deq Ptr cmd failed
due to incorrect slot or ep state.
[63308.687045] sd 2:0:0:0: [sdb] tag#2 uas_eh_abort_handler 0 uas-tag
3 inflight: CMD
[63308.687092] sd 2:0:0:0: [sdb] tag#2 CDB: Synchronize Cache(10) 35
00 00 00 00 00 00 00 00 00
[63308.687253] scsi host2: uas_eh_device_reset_handler start
[63308.803637] usb 2-2: reset SuperSpeed USB device number 3 using xhci_hcd
[63308.820480] scsi host2: uas_eh_device_reset_handler success
[chris@f27s ~]$
If I use a quirk to disable uas for this drive, the problem doesn't happen.
/etc/modprobe.d/ignore_uas.conf containing the line:
options usb-storage quirks=152d:0567:u
And without the quirk the problem also doesn't happen if the drive is
connected to a powered USB hub.
This enclosure works out of the box without problems on Windows 10 on
the same hardware, as well as on a Mac.
Thanks,
--
Chris Murphy
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
