On Wed, Jan 3, 2018 at 4:58 PM, Manu Gautam <mgautam@xxxxxxxxxxxxxx> wrote:
> Use register layout to add additional registers present
> on QUSB2 PHY V2 version for PHY initialization.
> Other than new registers on V2, following two register's
> offset and bit definitions are different: POWERDOWN control
> and PLL_STATUS.
>
> Signed-off-by: Manu Gautam <mgautam@xxxxxxxxxxxxxx>
> ---
> drivers/phy/qualcomm/phy-qcom-qusb2.c | 64 +++++++++++++++++++++++++++++++++++
> 1 file changed, 64 insertions(+)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
> index b65635f..8d0579e 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qusb2.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
> @@ -40,15 +40,34 @@
> /* QUSB2PHY_PLL_STATUS register bits */
> #define PLL_LOCKED BIT(5)
>
> +/* QUSB2PHY_PLL_COMMON_STATUS_ONE register bits */
> +#define CORE_READY_STATUS BIT(0)
> +
> /* QUSB2PHY_PORT_POWERDOWN register bits */
> #define CLAMP_N_EN BIT(5)
> #define FREEZIO_N BIT(1)
> #define POWER_DOWN BIT(0)
>
> +/* QUSB2PHY_PWR_CTRL1 register bits */
> +#define PWR_CTRL1_VREF_SUPPLY_TRIM BIT(5)
> +#define PWR_CTRL1_CLAMP_N_EN BIT(1)
> +
> #define QUSB2PHY_REFCLK_ENABLE BIT(0)
>
> #define PHY_CLK_SCHEME_SEL BIT(0)
>
> +#define QUSB2PHY_PLL_ANALOG_CONTROLS_TWO 0x04
> +#define QUSB2PHY_PLL_CLOCK_INVERTERS 0x18c
> +#define QUSB2PHY_PLL_CMODE 0x2c
> +#define QUSB2PHY_PLL_LOCK_DELAY 0x184
> +#define QUSB2PHY_PLL_DIGITAL_TIMERS_TWO 0xb4
> +#define QUSB2PHY_PLL_BIAS_CONTROL_1 0x194
> +#define QUSB2PHY_PLL_BIAS_CONTROL_2 0x198
> +#define QUSB2PHY_PWR_CTRL2 0x214
> +#define QUSB2PHY_IMP_CTRL1 0x220
> +#define QUSB2PHY_IMP_CTRL2 0x224
> +#define QUSB2PHY_CHG_CTRL2 0x23c
nit: Replace these tabs with simple spaces.
Rest all look good.
Reviewed-by: Vivek Gautam <vivek.gautam@xxxxxxxxxxxxxx>
Thanks
Vivek
> +
> struct qusb2_phy_init_tbl {
> unsigned int offset;
> unsigned int val;
> @@ -113,6 +132,38 @@ enum qusb2phy_reg_layout {
> QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00),
> };
>
> +static const unsigned int qusb2_v2_regs_layout[] = {
> + [QUSB2PHY_PLL_STATUS] = 0x1a0,
> + [QUSB2PHY_PORT_TUNE1] = 0x240,
> + [QUSB2PHY_PORT_TUNE2] = 0x244,
> + [QUSB2PHY_PORT_TUNE3] = 0x248,
> + [QUSB2PHY_PORT_TUNE4] = 0x24c,
> + [QUSB2PHY_PORT_TUNE5] = 0x250,
> + [QUSB2PHY_PORT_TEST2] = 0x258,
> + [QUSB2PHY_PORT_POWERDOWN] = 0x210,
> +};
> +
> +static const struct qusb2_phy_init_tbl qusb2_v2_init_tbl[] = {
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x03),
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c),
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80),
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a),
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19),
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_1, 0x40),
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_2, 0x20),
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PWR_CTRL2, 0x21),
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL1, 0x0),
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL2, 0x58),
> +
> + QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0x30),
> + QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x29),
> + QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0xca),
> + QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0x04),
> + QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE5, 0x03),
> +
> + QUSB2_PHY_INIT_CFG(QUSB2PHY_CHG_CTRL2, 0x0),
> +};
> +
> struct qusb2_phy_cfg {
> const struct qusb2_phy_init_tbl *tbl;
> /* number of entries in the table */
> @@ -142,6 +193,16 @@ struct qusb2_phy_cfg {
> .mask_core_ready = PLL_LOCKED,
> };
>
> +static const struct qusb2_phy_cfg qusb2_v2_phy_cfg = {
> + .tbl = qusb2_v2_init_tbl,
> + .tbl_num = ARRAY_SIZE(qusb2_v2_init_tbl),
> + .regs = qusb2_v2_regs_layout,
> +
> + .disable_ctrl = (PWR_CTRL1_VREF_SUPPLY_TRIM | PWR_CTRL1_CLAMP_N_EN |
> + POWER_DOWN),
> + .mask_core_ready = CORE_READY_STATUS,
> +};
> +
> static const char * const qusb2_phy_vreg_names[] = {
> "vdda-pll", "vdda-phy-dpdm",
> };
> @@ -429,6 +490,9 @@ static int qusb2_phy_exit(struct phy *phy)
> {
> .compatible = "qcom,msm8996-qusb2-phy",
> .data = &msm8996_phy_cfg,
> + }, {
> + .compatible = "qcom,qusb2-v2-phy",
> + .data = &qusb2_v2_phy_cfg,
> },
> { },
> };
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
