Hi Martin,
On Tue, 2017-10-31 at 00:10 +0100, Martin Blumenstingl wrote:
> Hi Manu,
>
> thank you for reviewing this!
>
> On Thu, Oct 26, 2017 at 7:42 AM, Manu Gautam <mgautam@xxxxxxxxxxxxxx> wrote:
> > Hi,
> >
> >
> > On 10/24/2017 3:27 AM, Martin Blumenstingl wrote:
> >> This integrates the PHY roothub wrapper into the core hcd
> >> infrastructure. Multiple PHYs which are part of the roothub devicetree
> >> node (which is a sub-node of the sysdev's node) are now managed
> >> (= powered on/off when needed), by the new usb_phy_roothub code.
> >>
> >> One example where this is required is the Amlogic GXL and GXM SoCs:
> >> They are using a dwc3 USB controller with up to three ports enabled on
> >> the internal roothub. Using only the top-level "phy" properties does not
> >> work here since one can only specify one "usb2-phy" and one "usb3-phy",
> >> while actually at least two "usb2-phy" have to be specified.
> >>
> >> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
> >> Tested-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
> >> Acked-by: Alan Stern <stern@xxxxxxxxxxxxxxxxxxx>
> >> ---
> >> drivers/usb/core/hcd.c | 26 ++++++++++++++++++++++++++
> >> include/linux/usb/hcd.h | 1 +
> >> 2 files changed, 27 insertions(+)
> >>
> >> diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
> >> index 67aa3d039b9b..6ee97222cdad 100644
> >> --- a/drivers/usb/core/hcd.c
> >> +++ b/drivers/usb/core/hcd.c
> >> @@ -50,6 +50,7 @@
> >> #include <linux/usb/otg.h>
> >>
> >> #include "usb.h"
> >> +#include "phy.h"
> >>
> >>
> >> /*-------------------------------------------------------------------------*/
> >> @@ -2271,6 +2272,8 @@ int hcd_bus_suspend(struct usb_device *rhdev, pm_message_t msg)
> >> usb_set_device_state(rhdev, USB_STATE_SUSPENDED);
> >> hcd->state = HC_STATE_SUSPENDED;
> >>
> >> + usb_phy_roothub_power_off(hcd->phy_roothub);
> >> +
> >
> > For system-suspend it should be ok.
> > But, in case of runtime/auto suspend, I think PHYs shouldn't be powered off.
> > Should we have check for that like-
> >
> > if (!PMSG_IS_AUTO(msg))
> > usb_phy_roothub_power_off()
> >
I test it after adding "if (!PMSG_IS_AUTO(msg)) ...", the PHYS are not
powered off in the case of runtime/auto suspend (hcd-bus automatically
suspend if no devices are attached), but powered off when system enter
suspend mode by "echo mem > /sys/power/state" etc.
So the behavior is the same as the earlier version that the PHYs are
directly controlled by the host driver, maybe this is a better way for
backward compatibility.
> > Similar check in hcd_bus_resume?
> disclaimer: I must admit that I am not very familiar with the PM code
> and even worse: the platform I'm developing with does not have suspend support
>
> can I take your suggestion and include it in the next version of this
> series or should we wait for feedback from another developer on this
> topic?
>
> >
> >> /* Did we race with a root-hub wakeup event? */
> >> if (rhdev->do_remote_wakeup) {
> >> char buffer[6];
> >> @@ -2307,6 +2310,11 @@ int hcd_bus_resume(struct usb_device *rhdev, pm_message_t msg)
> >> dev_dbg(&rhdev->dev, "skipped %s of dead bus\n", "resume");
> >> return 0;
> >> }
> >> +
> >> + status = usb_phy_roothub_power_on(hcd->phy_roothub);
> >> + if (status)
> >> + return status;
> >> +
> >
> > --
> > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> > a Linux Foundation Collaborative Project
> >
>
>
> Regards
> Martin
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
