On 21.05.2017 23:03, Xavier . wrote:
Hello.
I have one problem with chip Renesas uPD720202 (card Startech PCIUSB3S22).
In Windows XP run fine, very fine, but in GNU/Linux kernel does not
receive any USB3.0 plug/unplug events, why?
No usb device is recognized, it is as if the card had nothing connected.
I have tried the following kernels:
Linux version 4.12.0-041200rc1-generic (kernel@gomeisa) (gcc version
6.3.0 20170510 (Ubuntu 6.3.0-17ubuntu1) ) #201705131731 SMP Sat May 13
21:48:41 UTC 2017
Linux version 4.11.1-041101-generic (kernel@tangerine) (gcc version
6.3.0 20170510 (Ubuntu 6.3.0-17ubuntu1) ) #201705140931 SMP Sun May 14
13:50:33 UTC 2017
In no case kernel does not receive any USB plug/unplug events
The card firmware is the latest (2026) and is well installed.
My machine is very old: P3 1Ghz on ASUS P3B-F but run fine
Xavier.
Thanks
dmesg.4.12-rc1.with_pendrive_connected_at_boot:
[ 3.762590] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 3.762612] xhci_hcd 0000:02:00.0: new USB bus registered, assigned
bus number 2
[ 4.014404] xhci_hcd 0000:02:00.0: Host halt failed, -19
[ 4.014410] xhci_hcd 0000:02:00.0: can't setup: -19
[ 4.015145] ata1.00: ATAPI: HL-DT-ST RW/DVD GCC-4521B, 1.07, max UDMA/33
[ 4.015414] ata2: port disabled--ignoring
[ 4.015774] xhci_hcd 0000:02:00.0: USB bus 2 deregistered
[ 4.036586] xhci_hcd 0000:02:00.0: init 0000:02:00.0 fail, -19
host halt failed -19 (ENODEV), we are reading 0xffffffff from the status register
which is located at xhci MMIO base + CAPLENGTH + 0x04
lspci.4.12-rc1
02:00.0 USB controller: Renesas Technology Corp. uPD720202 USB 3.0
Host Controller (rev 02) (prog-if 30 [XHCI])
Subsystem: Renesas Technology Corp. uPD720202 USB 3.0 Host Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b5000000 (64-bit, non-prefetchable) [size=8K]
8k looks small
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [90] MSI-X: Enable+ Count=8 Masked-
Vector table: BAR=0 offset=00001000
PBA: BAR=0 offset=00001080
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
MSI not capable
MSIX ok
/proc/ionterrupts showed two xhci entries:
16: 0 PCI-MSI-edge xhci_hcd
17: 0 PCI-MSI-edge xhci_hcd
Does xhci dynamic debug show anything during boot?
add to kernel cmdline:
dyndbg='module xhci_hcd +p'
-Mathias
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
