Hello Grygorii,
On 03/24/2017 06:26 PM, Grygorii Strashko wrote:
On 03/24/2017 09:36 AM, Alexandre Bailon wrote:
> Currently, MUSB DA8xx glue driver doesn't have PM runtime support.
> Because the CPPI 4.1 is using the same clock as MUSB DA8xx and
> CPPI 4.1 is a child of MUSB DA8xx glue, add support of PM runtime
> to the DA8xx glue driver in order to let the CPPI 4.1 driver manage
> the clock by using PM runtime.
>
> Signed-off-by: Alexandre Bailon <abailon@xxxxxxxxxxxx>
> ---
> drivers/usb/musb/da8xx.c | 27 ++++++++-------------------
> 1 file changed, 8 insertions(+), 19 deletions(-)
>
> diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c
> index ed28afd..89e12f6 100644
> --- a/drivers/usb/musb/da8xx.c
> +++ b/drivers/usb/musb/da8xx.c
> @@ -30,7 +30,6 @@
> */
>
[...]
>
> @@ -527,12 +520,6 @@ static int da8xx_probe(struct platform_device *pdev)
> if (!glue)
> return -ENOMEM;
>
> - clk = devm_clk_get(&pdev->dev, "usb20");
> - if (IS_ERR(clk)) {
> - dev_err(&pdev->dev, "failed to get clock\n");
> - return PTR_ERR(clk);
> - }
> -
> glue->phy = devm_phy_get(&pdev->dev, "usb-phy");
> if (IS_ERR(glue->phy)) {
> if (PTR_ERR(glue->phy) != -EPROBE_DEFER)
> @@ -541,7 +528,6 @@ static int da8xx_probe(struct platform_device *pdev)
> }
>
> glue->dev = &pdev->dev;
> - glue->clk = clk;
>
> if (IS_ENABLED(CONFIG_OF) && np) {
> pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
> @@ -587,6 +573,8 @@ static int da8xx_probe(struct platform_device *pdev)
> pinfo.data = pdata;
> pinfo.size_data = sizeof(*pdata);
>
> + pm_runtime_enable(&pdev->dev);
> +
> glue->musb = platform_device_register_full(&pinfo);
> ret = PTR_ERR_OR_ZERO(glue->musb);
> if (ret) {
> @@ -603,6 +591,7 @@ static int da8xx_remove(struct platform_device *pdev)
>
> platform_device_unregister(glue->musb);
> usb_phy_generic_unregister(glue->usb_phy);
> + pm_runtime_disable(&pdev->dev);
>
> return 0;
> }
> @@ -616,7 +605,7 @@ static int da8xx_suspend(struct device *dev)
> ret = phy_power_off(glue->phy);
> if (ret)
> return ret;
> - clk_disable_unprepare(glue->clk);
> + pm_runtime_put_sync(dev);
This, most probably will do nothing as Suspend framework will increase ref counter.
Better way might be to use PM runtime force API. pm_runtime_force_suspend()
Good catch. Effectively, the device remain active.
But we can't use pm_runtime_force_suspend() because it expect that all child have been
runtime suspended which is usually not the case.
>
> return 0;
> }
> @@ -626,7 +615,7 @@ static int da8xx_resume(struct device *dev)
> int ret;
> struct da8xx_glue *glue = dev_get_drvdata(dev);
>
> - ret = clk_prepare_enable(glue->clk);
> + ret = pm_runtime_get_sync(dev);
> if (ret)
> return ret;
Better way might be to use PM runtime force API.
Again, it will not work. Because the forced runtime suspend will not complete
because child are not runtime suspended then the resume will not happen.
> return phy_power_on(glue->phy);
>
Do you have any other suggestions to fix it?
My original intent was to give a way to CPPI 4.1 DMA driver to enable or
disable the usb20 clock owned DA8xx USB glue driver.
Thanks,
Alexandre
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
