This patch introduces a new parameter to activate USB OTG HS/FS core embedded
phy transceiver. The STM32F4x9 SoC uses the GGPIO register to enable the transceiver.
Also add the dwc2_core_params structure for stm32f4 otg fs.
Signed-off-by: Bruno Herrera <bruherrera@xxxxxxxxx>
---
drivers/usb/dwc2/core.h | 4 ++++
drivers/usb/dwc2/hcd.c | 13 +++++++++++-
drivers/usb/dwc2/hw.h | 2 ++
drivers/usb/dwc2/params.c | 51 +++++++++++++++++++++++++++++++++++++++++++++++
4 files changed, 69 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/dwc2/core.h b/drivers/usb/dwc2/core.h
index 9548d3e..e3199c5 100644
--- a/drivers/usb/dwc2/core.h
+++ b/drivers/usb/dwc2/core.h
@@ -430,6 +430,9 @@ enum dwc2_ep0_state {
* needed.
* 0 - No (default)
* 1 - Yes
+ * @activate_transceiver: Activate internal transceiver using GGPIO register.
+ * 0 - Deactivate the transceiver (default)
+ * 1 - Activate the transceiver
* @g_dma: Enables gadget dma usage (default: autodetect).
* @g_dma_desc: Enables gadget descriptor DMA (default: autodetect).
* @g_rx_fifo_size: The periodic rx fifo size for the device, in
@@ -501,6 +504,7 @@ struct dwc2_core_params {
int uframe_sched;
int external_id_pin_ctl;
int hibernation;
+ int activate_transceiver;
/*
* The following parameters are *only* set via device
diff --git a/drivers/usb/dwc2/hcd.c b/drivers/usb/dwc2/hcd.c
index 911c3b3..6bee529 100644
--- a/drivers/usb/dwc2/hcd.c
+++ b/drivers/usb/dwc2/hcd.c
@@ -118,7 +118,7 @@ static void dwc2_init_fs_ls_pclk_sel(struct dwc2_hsotg *hsotg)
static int dwc2_fs_phy_init(struct dwc2_hsotg *hsotg, bool select_phy)
{
- u32 usbcfg, i2cctl;
+ u32 usbcfg, ggpio, i2cctl;
int retval = 0;
/*
@@ -142,6 +142,17 @@ static int dwc2_fs_phy_init(struct dwc2_hsotg *hsotg, bool select_phy)
return retval;
}
}
+
+ ggpio = dwc2_readl(hsotg->regs + GGPIO);
+ if (!(ggpio & GGPIO_STM32_OTG_GCCFG_PWRDWN) &&
+ (hsotg->params.activate_transceiver > 0)) {
+ dev_dbg(hsotg->dev, "Activating transceiver\n");
+ /* STM32F4xx uses the GGPIO register as general core
+ * configuration register.
+ */
+ ggpio |= GGPIO_STM32_OTG_GCCFG_PWRDWN;
+ dwc2_writel(ggpio, hsotg->regs + GGPIO);
+ }
}
/*
diff --git a/drivers/usb/dwc2/hw.h b/drivers/usb/dwc2/hw.h
index 5be056b..a84e93b 100644
--- a/drivers/usb/dwc2/hw.h
+++ b/drivers/usb/dwc2/hw.h
@@ -225,6 +225,8 @@
#define GPVNDCTL HSOTG_REG(0x0034)
#define GGPIO HSOTG_REG(0x0038)
+#define GGPIO_STM32_OTG_GCCFG_PWRDWN (1 << 16)
+
#define GUID HSOTG_REG(0x003c)
#define GSNPSID HSOTG_REG(0x0040)
#define GHWCFG1 HSOTG_REG(0x0044)
diff --git a/drivers/usb/dwc2/params.c b/drivers/usb/dwc2/params.c
index 11fe68a..dbb054d 100644
--- a/drivers/usb/dwc2/params.c
+++ b/drivers/usb/dwc2/params.c
@@ -192,6 +192,37 @@ static const struct dwc2_core_params params_amlogic = {
.hibernation = -1,
};
+static const struct dwc2_core_params params_stm32f4_otgfs = {
+ .otg_cap = DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE,
+ .otg_ver = -1,
+ .dma_desc_enable = 0,
+ .dma_desc_fs_enable = 0,
+ .speed = DWC2_SPEED_PARAM_FULL,
+ .enable_dynamic_fifo = -1,
+ .en_multiple_tx_fifo = -1,
+ .host_rx_fifo_size = 128, /* 128 DWORDs */
+ .host_nperio_tx_fifo_size = 96, /* 96 DWORDs */
+ .host_perio_tx_fifo_size = 96, /* 96 DWORDs */
+ .max_transfer_size = -1,
+ .max_packet_count = 256,
+ .host_channels = -1,
+ .phy_type = DWC2_PHY_TYPE_PARAM_FS,
+ .phy_utmi_width = -1,
+ .phy_ulpi_ddr = -1,
+ .phy_ulpi_ext_vbus = -1,
+ .i2c_enable = 0,
+ .ulpi_fs_ls = -1,
+ .host_support_fs_ls_low_power = -1,
+ .host_ls_low_power_phy_clk = -1,
+ .ts_dline = -1,
+ .reload_ctl = -1,
+ .ahbcfg = -1,
+ .uframe_sched = 0,
+ .external_id_pin_ctl = -1,
+ .hibernation = -1,
+ .activate_transceiver = 1,
+};
+
static const struct dwc2_core_params params_default = {
.otg_cap = -1,
.otg_ver = -1,
@@ -240,6 +271,8 @@ const struct of_device_id dwc2_of_match_table[] = {
{ .compatible = "amlogic,meson8b-usb", .data = ¶ms_amlogic },
{ .compatible = "amlogic,meson-gxbb-usb", .data = ¶ms_amlogic },
{ .compatible = "amcc,dwc-otg", .data = NULL },
+ { .compatible = "st,stm32f4xx-fsotg", .data = ¶ms_stm32f4_otgfs },
+ { .compatible = "st,stm32f4xx-hsotg", .data = NULL },
{},
};
MODULE_DEVICE_TABLE(of, dwc2_of_match_table);
@@ -1044,6 +1077,23 @@ static void dwc2_set_param_hibernation(struct dwc2_hsotg *hsotg,
hsotg->params.hibernation = val;
}
+static void dwc2_set_param_activate_transceiver(struct dwc2_hsotg *hsotg,
+ int val)
+{
+ if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) {
+ if (val >= 0) {
+ dev_err(hsotg->dev,
+ "'%d' invalid for parameter activate transceiver\n",
+ val);
+ dev_err(hsotg->dev, "activate transceiver must be 0 or 1\n");
+ }
+ val = 0;
+ dev_dbg(hsotg->dev, "Setting activate transceiver to %d\n", val);
+ }
+
+ hsotg->params.activate_transceiver = val;
+}
+
static void dwc2_set_param_tx_fifo_sizes(struct dwc2_hsotg *hsotg)
{
int i;
@@ -1158,6 +1208,7 @@ static void dwc2_set_parameters(struct dwc2_hsotg *hsotg,
dwc2_set_param_uframe_sched(hsotg, params->uframe_sched);
dwc2_set_param_external_id_pin_ctl(hsotg, params->external_id_pin_ctl);
dwc2_set_param_hibernation(hsotg, params->hibernation);
+ dwc2_set_param_activate_transceiver(hsotg, params->activate_transceiver);
/*
* Set devicetree-only parameters. These parameters do not
--
2.10.1 (Apple Git-78)
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
