Re: VL805 USB 3.0 does not see connected devices (only on x86_64) (x86 is ok)

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



>Obviously you're not reading my email messages.  I told you quite
>clearly:
>
>        After unloading the xhci-pci and xhci-hcd modules:
>
>        sudo modprobe xhci_hcd quirks=0x00800090
>        sudo modprobe xhci_pci
===============================================
this part of commands from your message were done right as you`ve sent
i thought you`ve seen the result in DMESG (i`ve sent it twice)
i even tried rmmod previously
USB does not work either

2016-09-15 0:45 GMT+03:00 c400 <c400c400@xxxxxxxxx>:
> XHCI_NO_64BIT_SUPPORT
> can't find such flag in my kernel config. May be you can help me to
> find it in menuconfig tree?
>
> 2016-09-14 23:25 GMT+03:00 c400 <c400c400@xxxxxxxxx>:
>> yep! enabling You need to enable CONFIG_DYNAMIC_DEBUG. did the trick!
>> here is my new dmesg output:
>>
>>
>> 2016-09-14 22:39 GMT+03:00 c400 <c400c400@xxxxxxxxx>:
>>> 2016-09-14 15:43 GMT+03:00 Oliver Neukum <oneukum@xxxxxxxx>:
>>>> On Wed, 2016-09-14 at 15:22 +0300, c400 wrote:
>>>>> may be i can help to test something else? I am ready and have enough free time
>>>>
>>>> You may need to mount debugfs at /sys/kernel/debug
>>>>
>>>>         HTH
>>>>                 Oliver
>>>>
>>>>
>>> mount -t debugfs none /sys/kernel/debug/
>>> mount: none is already mounted or /sys/kernel/debug busy
>>>
>>> ls /sys/kernel/debug/
>>>
>>> acpi         extfrag             mce         sleep_time
>>> bcache       fault_around_bytes  nfsd        suspend_stats
>>> bdi          hid                 pm_qos      tracing
>>> boot_params  hwpoison            pstate_snb  usb
>>> dma_buf      intel_powerclamp    ras         wakeup_sources
>>> dri          kprobes             regmap      x86
>>>
>>> 2016-09-14 15:22 GMT+03:00 c400 <c400c400@xxxxxxxxx>:
>>>> may be i can help to test something else? I am ready and have enough free time
>>>>
>>>> 2016-09-12 20:44 GMT+03:00 c400 <c400c400@xxxxxxxxx>:
>>>>> [182047.000570] xhci_hcd 0000:02:00.0: remove, state 4
>>>>> [182047.000577] usb usb4: USB disconnect, device number 1
>>>>> [182047.023980] xhci_hcd 0000:02:00.0: Host not halted after 16000 microseconds.
>>>>> [182047.023982] xhci_hcd 0000:02:00.0: Host controller not halted,
>>>>> aborting reset.
>>>>> [182047.023996] xhci_hcd 0000:02:00.0: USB bus 4 deregistered
>>>>> [182047.024103] xhci_hcd 0000:02:00.0: remove, state 1
>>>>> [182047.024108] usb usb3: USB disconnect, device number 1
>>>>> [182047.024320] xhci_hcd 0000:02:00.0: USB bus 3 deregistered
>>>>> [182058.617466] xhci_hcd 0000:02:00.0: xHCI Host Controller
>>>>> [182058.617556] xhci_hcd 0000:02:00.0: new USB bus registered,
>>>>> assigned bus number 3
>>>>> [182058.640820] xhci_hcd 0000:02:00.0: Host not halted after 16000 microseconds.
>>>>> [182058.640822] xhci_hcd 0000:02:00.0: can't setup: -110
>>>>> [182058.640824] xhci_hcd 0000:02:00.0: USB bus 3 deregistered
>>>>> [182058.640944] xhci_hcd 0000:02:00.0: init 0000:02:00.0 fail, -110
>>>>> [182058.640947] xhci_hcd: probe of 0000:02:00.0 failed with error -110
>>>>>
>>>>> can not see my flash inserted into the USB
>>>>>
>>>>> echo -n 'module xhci_hcd =p' > /sys/kernel/debug/dynamic_debug/control
>>>>> Do not have such folder
>>>>> (i`ve recompiled my kernel (make defconfig) with some small changes.
>>>>> may be i need to enable something in kernelt?
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux