Hi John, > John Youn <John.Youn@xxxxxxxxxxxx> hat am 17. August 2016 um 23:21 > geschrieben: > > > ... > Ok, yeah, that seems better. > > Can you check if applying just patch 2 and 3 solves the issue? If so I > think we can send those upstream. unfortunately not: [ 2.280719] dwc2_lowlevel_hw_init() [ 2.288028] dwc2_set_all_params() [ 2.295162] dwc2_lowlevel_hw_enable() [ 2.302439] dwc2_get_dr_mode() [ 2.309043] dwc2_core_reset_and_force_dr_mode() [ 2.489040] dwc2_get_hwparams() [ 2.495629] dwc2 20980000.usb: Core Release: 2.80a (snpsid=4f54280a) [ 2.495645] dwc2 20980000.usb: hwcfg1=00000000 [ 2.495657] dwc2 20980000.usb: hwcfg2=228ddd50 [ 2.495668] dwc2 20980000.usb: hwcfg3=0ff000e8 [ 2.495680] dwc2 20980000.usb: hwcfg4=1ff00020 [ 2.495691] dwc2 20980000.usb: grxfsiz=00001000 [ 2.495701] dwc2 20980000.usb: Forcing mode to host [ 2.539076] dwc2 20980000.usb: gnptxfsiz=00201000 [ 2.539090] dwc2 20980000.usb: hptxfsiz=00000000 [ 2.589054] dwc2 20980000.usb: gnptxfsiz=00201000 [ 2.589071] dwc2 20980000.usb: Detected values from hardware: [ 2.589082] dwc2 20980000.usb: op_mode=0 [ 2.589093] dwc2 20980000.usb: arch=2 [ 2.589104] dwc2 20980000.usb: dma_desc_enable=0 [ 2.589115] dwc2 20980000.usb: power_optimized=0 [ 2.589125] dwc2 20980000.usb: i2c_enable=0 [ 2.589134] dwc2 20980000.usb: hs_phy_type=1 [ 2.589144] dwc2 20980000.usb: fs_phy_type=1 [ 2.589154] dwc2 20980000.usb: utmi_phy_data_width=0 [ 2.589164] dwc2 20980000.usb: num_dev_ep=7 [ 2.589174] dwc2 20980000.usb: num_dev_perio_in_ep=0 [ 2.589183] dwc2 20980000.usb: host_channels=8 [ 2.589195] dwc2 20980000.usb: max_transfer_size=524287 [ 2.589206] dwc2 20980000.usb: max_packet_count=1023 [ 2.589216] dwc2 20980000.usb: nperio_tx_q_depth=0x4 [ 2.589226] dwc2 20980000.usb: host_perio_tx_q_depth=0x4 [ 2.589236] dwc2 20980000.usb: dev_token_q_depth=0x8 [ 2.589247] dwc2 20980000.usb: enable_dynamic_fifo=1 [ 2.589257] dwc2 20980000.usb: en_multiple_tx_fifo=1 [ 2.589267] dwc2 20980000.usb: total_fifo_size=4080 [ 2.589277] dwc2 20980000.usb: host_rx_fifo_size=4096 [ 2.589287] dwc2 20980000.usb: host_nperio_tx_fifo_size=32 [ 2.589299] dwc2 20980000.usb: host_perio_tx_fifo_size=0 [ 2.589307] dwc2 20980000.usb: [ 2.589312] dwc2_set_parameters() [ 2.595921] dwc2 20980000.usb: dwc2_set_parameters() [ 2.595940] dwc2 20980000.usb: Setting dma_desc_fs_enable to 0 [ 2.595968] dwc2 20980000.usb: Setting external_id_pin_ctl to 0 [ 2.595980] dwc2 20980000.usb: Setting hibernation to 0 [ 2.596003] dwc2 20980000.usb: 256 invalid for host_nperio_tx_fifo_size. Check HW configuration. [ 2.611528] dwc2 20980000.usb: Setting host_nperio_tx_fifo_size to 32 [ 2.611552] dwc2 20980000.usb: 512 invalid for host_perio_tx_fifo_size. Check HW configuration. [ 2.627250] dwc2 20980000.usb: Setting host_perio_tx_fifo_size to 0 [ 2.627256] dwc2_force_dr_mode() [ 2.749035] dwc2_gadget_init() [ 2.755610] dwc2 20980000.usb: Specified GNPTXFDEP=1024 > 32 [ 2.764876] dwc2 20980000.usb: EPs: 8, dedicated fifos, 4080 entries in SPRAM [ 2.792911] dwc2 20980000.usb: bound driver zero [ 2.801042] dwc2_hcd_init() [ 2.807485] dwc2 20980000.usb: DWC OTG Controller [ 2.815716] dwc2 20980000.usb: new USB bus registered, assigned bus number 1 [ 2.826265] dwc2 20980000.usb: irq 33, io mem 0x00000000 Regards Stefan > > Regards, > John -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
