Use C_X tty.h macros to avoid direct manipulation of termios c_cflag variable. Signed-off-by: Mathieu OTHACEHE <m.othacehe@xxxxxxxxx> --- drivers/usb/serial/ti_usb_3410_5052.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c index c8ed3f9..29bb62c 100644 --- a/drivers/usb/serial/ti_usb_3410_5052.c +++ b/drivers/usb/serial/ti_usb_3410_5052.c @@ -955,7 +955,7 @@ static void ti_set_termios(struct tty_struct *tty, wflags |= TI_UART_ENABLE_AUTO_START_DMA; config->bUartMode = tport->tp_uart_mode; - switch (cflag & CSIZE) { + switch (C_CSIZE(tty)) { case CS5: config->bDataBits = TI_UART_5_DATA_BITS; break; @@ -974,8 +974,8 @@ static void ti_set_termios(struct tty_struct *tty, /* CMSPAR isn't supported by this driver */ tty->termios.c_cflag &= ~CMSPAR; - if (cflag & PARENB) { - if (cflag & PARODD) { + if (C_PARENB(tty)) { + if (C_PARODD(tty)) { wflags |= TI_UART_ENABLE_PARITY_CHECKING; config->bParity = TI_UART_ODD_PARITY; } else { @@ -987,14 +987,14 @@ static void ti_set_termios(struct tty_struct *tty, config->bParity = TI_UART_NO_PARITY; } - if (cflag & CSTOPB) + if (C_CSTOPB(tty)) config->bStopBits = TI_UART_2_STOP_BITS; else config->bStopBits = TI_UART_1_STOP_BITS; - if (cflag & CRTSCTS) { + if (C_CRTSCTS(tty)) { /* RTS flow control must be off to drop RTS for baud rate B0 */ - if ((cflag & CBAUD) != B0) + if ((C_BAUD(tty)) != B0) wflags |= TI_UART_ENABLE_RTS_IN; wflags |= TI_UART_ENABLE_CTS_OUT; } else { @@ -1023,7 +1023,7 @@ static void ti_set_termios(struct tty_struct *tty, wbaudrate = (461538 + baud/2) / baud; /* FIXME: Should calculate resulting baud here and report it back */ - if ((cflag & CBAUD) != B0) + if ((C_BAUD(tty)) != B0) tty_encode_baud_rate(tty, baud, baud); dev_dbg(&port->dev, @@ -1045,7 +1045,7 @@ static void ti_set_termios(struct tty_struct *tty, /* SET_CONFIG asserts RTS and DTR, reset them correctly */ mcr = tport->tp_shadow_mcr; /* if baud rate is B0, clear RTS and DTR */ - if ((cflag & CBAUD) == B0) + if (C_BAUD(tty) == B0) mcr &= ~(TI_MCR_DTR | TI_MCR_RTS); status = ti_set_mcr(tport, mcr); if (status) -- 2.9.0 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html