Hi Doug,
On 2016/7/21 5:33, Doug Anderson wrote:
Hi,
On Tue, Jul 19, 2016 at 12:28 AM, Frank Wang <frank.wang@xxxxxxxxxxxxxx> wrote:
You need a patch description here, even for simple patches. All you
have now is a subject.
OK, I will describe it next version.
Signed-off-by: Frank Wang <frank.wang@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/rockchip/rk3399-evb.dts | 19 +++++++++++
arch/arm64/boot/dts/rockchip/rk3399.dtsi | 47 ++++++++++++++++++++++++++-
Personally I'd prefer to see EVB in a separate patch.
Yep, I would like to separate them :-) .
2 files changed, 65 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
index 1a3eb14..31d4828 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
@@ -69,6 +69,15 @@
regulator-max-microvolt = <3300000>;
};
+ vbus_host: vbus-host-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vbus_host";
+ };
+
To match my schematics, this would probably be "vcc5v0_host".
Technically there are two regulators but since they are the same
voltage and enabled by the same GPIO it seems like modeling it as one
regulator is fine.
Yep, you are right, I will rename it.
If you really wanted to model things you could also include the input
supply (VCC5V0_SYS). Not sure how much you care to model in EVB.
Actually, from
"Documentation/devicetree/bindings/regulator/fixed-regulator.txt" show,
input supply name is just optional property, and it seems that only do
assign "vin" value for input_supply (the second member of struct
fixed_voltage_config) if "vin-supply" is specified.
So is input supply name (VCC5V0_SYS) required here? Would you like to
give more comments please?
vcc_phy: vcc-phy-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_phy";
@@ -93,6 +102,16 @@
status = "okay";
};
+&u2phy0_host {
+ phy-supply = <&vbus_host>;
+ status = "okay";
+};
+
+&u2phy1_host {
+ phy-supply = <&vbus_host>;
+ status = "okay";
+};
+
Technically "u2" sorts alphabetically before "uart".
Well, It will be sorted next version.
&usb_host0_ehci {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index d7f8e06..0383785 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -221,6 +221,8 @@
interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>;
clock-names = "hclk_host0", "hclk_host0_arb";
+ phys = <&u2phy0_host>;
+ phy-names = "u2phy0";
This is wrong. From
"Documentation/devicetree/bindings/usb/usb-ehci.txt" phy-names should
be "usb".
done.
status = "disabled";
};
@@ -239,6 +241,8 @@
interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>;
clock-names = "hclk_host1", "hclk_host1_arb";
+ phys = <&u2phy1_host>;
+ phy-names = "u2phy1";
This is wrong. From
"Documentation/devicetree/bindings/usb/usb-ehci.txt" phy-names should
be "usb".
done
status = "disabled";
};
@@ -481,8 +485,42 @@
};
grf: syscon@ff770000 {
- compatible = "rockchip,rk3399-grf", "syscon";
+ compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd";
reg = <0x0 0xff770000 0x0 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ u2phy0: usb2-phy@e450 {
+ compatible = "rockchip,rk3399-usb2phy";
+ reg = <0xe450 0x10>;
+ clocks = <&cru SCLK_USB2PHY0_REF>;
+ clock-names = "phyclk";
+ #clock-cells = <0>;
+ clock-output-names = "clk_usbphy0_480m";
Any reason why there isn't a 'status = "disabled";' here?
Refer to some explains from Heiko in another mail which sent at 6:07 AM
on 21th July, anyway, I will add ' status = "disabled" ' property next
version.
+ u2phy0_host: host-port {
+ #phy-cells = <0>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "linestate";
+ status = "disabled";
+ };
+ };
+
+ u2phy1: usb2-phy@e460 {
+ compatible = "rockchip,rk3399-usb2phy";
+ reg = <0xe460 0x10>;
+ clocks = <&cru SCLK_USB2PHY1_REF>;
+ clock-names = "phyclk";
+ #clock-cells = <0>;
+ clock-output-names = "clk_usbphy1_480m";
+
+ u2phy1_host: host-port {
+ #phy-cells = <0>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "linestate";
+ status = "disabled";
+ };
+ };
};
watchdog@ff840000 {
@@ -1009,5 +1047,12 @@
<1 14 RK_FUNC_1 &pcfg_pull_none>;
};
};
+
+ usb2 {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins =
+ <4 25 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
Are you certain this belongs in rk3399.dtsi? It seems like it should
be in the EVB file.
All right, It will be moved to EVB file next version.
BR.
Frank
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
