Thanks for the reply. Just this device and a mouse. Even with the mouse disconnected I have the same problem. I don't have an externally powered USB hub. The system should work without (external) power :( I'll try to borrow one somewhere, just to test it. regards, W im Tony Olech wrote: > Hi, > > you seem to have a few USB devices connected, have you > tried using an externally powered USB HUB? > > Tony Olech > Elan Digital Systems > > On Tue, 2009-01-20 at 17:25 +0100, Wim de Vries wrote: > >> Hi, >> I am trying to connect an USB device to my asus eee pc. >> The device connects OK on my HP compaq 6910p with Suse 10.3: >> dmesg: >> usb 7-1: new full speed USB device using uhci_hcd and address 4 >> usb 7-1: new device found, idVendor=04d8, idProduct=000a >> usb 7-1: new device strings: Mfr=1, Product=2, SerialNumber=3 >> usb 7-1: Product: PIC18 USB CDC >> usb 7-1: Manufacturer: Microchip >> usb 7-1: SerialNumber: V1.1FS >> usb 7-1: configuration #1 chosen from 1 choice >> drivers/usb/class/cdc-acm.c: This device cannot do calls on its own. It >> is no; modem. >> cdc_acm 7-1:1.0: ttyACM0: USB ACM device >> >> So it should ánd can use cdc-acm. >> >> Nevertheless, on the asus (kernel version: 2.6.26-1-686, Debian,KDE): >> >> dmesg: >> [ 0.000000] Initializing cgroup subsys cpuset >> [ 0.000000] Initializing cgroup subsys cpu >> [ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-11) >> (waldi@xxxxxxxxxx) (gcc version 4.1.3 20080623 (prerelease) (Debian >> 4.1.2-23)) #1 SMP Wed Nov 26 19:14:11 UTC 2008 >> [ 0.000000] BIOS-provided physical RAM map: >> [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) >> [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) >> [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) >> [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f780000 (usable) >> [ 0.000000] BIOS-e820: 000000003f780000 - 000000003f790000 (ACPI data) >> [ 0.000000] BIOS-e820: 000000003f790000 - 000000003f7d0000 (ACPI NVS) >> [ 0.000000] BIOS-e820: 000000003f7d0000 - 000000003f7de000 (reserved) >> [ 0.000000] BIOS-e820: 000000003f7e0000 - 000000003f800000 (reserved) >> [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) >> [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) >> [ 0.000000] 119MB HIGHMEM available. >> [ 0.000000] 896MB LOWMEM available. >> [ 0.000000] found SMP MP-table at [c00ff780] 000ff780 >> [ 0.000000] Entering add_active_range(0, 0, 259968) 0 entries of 256 used >> [ 0.000000] Zone PFN ranges: >> [ 0.000000] DMA 0 -> 4096 >> [ 0.000000] Normal 4096 -> 229376 >> [ 0.000000] HighMem 229376 -> 259968 >> [ 0.000000] Movable zone start PFN for each node >> [ 0.000000] early_node_map[1] active PFN ranges >> [ 0.000000] 0: 0 -> 259968 >> [ 0.000000] On node 0 totalpages: 259968 >> [ 0.000000] DMA zone: 32 pages used for memmap >> [ 0.000000] DMA zone: 0 pages reserved >> [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 >> [ 0.000000] Normal zone: 1760 pages used for memmap >> [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 >> [ 0.000000] HighMem zone: 239 pages used for memmap >> [ 0.000000] HighMem zone: 30353 pages, LIFO batch:7 >> [ 0.000000] Movable zone: 0 pages used for memmap >> [ 0.000000] DMI present. >> [ 0.000000] ACPI: RSDP 000FBE60, 0014 (r0 ACPIAM) >> [ 0.000000] ACPI: RSDT 3F780000, 0034 (r1 A M I OEMRSDT 9000811 MSFT >> 97) >> [ 0.000000] ACPI: FACP 3F780200, 0081 (r1 A M I OEMFACP 9000811 MSFT >> 97) >> [ 0.000000] ACPI: DSDT 3F780400, 6109 (r1 A0979 A0979034 34 INTL >> 20060113) >> [ 0.000000] ACPI: FACS 3F790000, 0040 >> [ 0.000000] ACPI: APIC 3F780390, 0068 (r1 A M I OEMAPIC 9000811 MSFT >> 97) >> [ 0.000000] ACPI: OEMB 3F790040, 0046 (r1 A M I AMI_OEM 9000811 MSFT >> 97) >> [ 0.000000] ACPI: MCFG 3F786510, 003C (r1 A M I OEMMCFG 9000811 MSFT >> 97) >> [ 0.000000] ACPI: PM-Timer IO Port: 0x808 >> [ 0.000000] ACPI: Local APIC address 0xfee00000 >> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) >> [ 0.000000] ACPI: Skipping IOAPIC probe due to 'noapic' option. >> [ 0.000000] Using ACPI for processor (LAPIC) configuration information >> [ 0.000000] Intel MultiProcessor Specification v1.4 >> [ 0.000000] Virtual Wire compatibility mode. >> [ 0.000000] MPTABLE: OEM ID: INTEL Product ID: <6>MPTABLE: Product >> ID: <6>MPTABLE: APIC at: 0xFEE00000 >> [ 0.000000] I/O APIC #1 Version 32 at 0xFEC00000. >> [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs >> [ 0.000000] Processors: 1 >> [ 0.000000] Allocating PCI resources starting at 40000000 (gap: >> 3f800000:bf600000) >> [ 0.000000] PM: Registered nosave memory: 000000000009f000 - >> 00000000000a0000 >> [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - >> 00000000000e4000 >> [ 0.000000] PM: Registered nosave memory: 00000000000e4000 - >> 0000000000100000 >> [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs >> [ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data >> [ 0.000000] NR_CPUS: 8, nr_cpu_ids: 1 >> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. >> Total pages: 257937 >> [ 0.000000] Kernel command line: root=/dev/sdb1 ro quiet noapic >> [ 0.000000] mapped APIC to ffffb000 (fee00000) >> [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) >> [ 0.000000] Enabling fast FPU save and restore... done. >> [ 0.000000] Enabling unmasked SIMD FPU exception support... done. >> [ 0.000000] Initializing CPU#0 >> [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) >> [ 0.000000] Detected 900.130 MHz processor. >> [ 0.004000] Console: colour VGA+ 80x25 >> [ 0.004000] console [tty0] enabled >> [ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 >> bytes) >> [ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) >> [ 0.004000] Memory: 1021104k/1039872k available (1768k kernel code, >> 18032k reserved, 752k data, 244k init, 122368k highmem) >> [ 0.004000] virtual kernel memory layout: >> [ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB) >> [ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) >> [ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) >> [ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) >> [ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB) >> [ 0.004000] .data : 0xc02ba293 - 0xc0376620 ( 752 kB) >> [ 0.004000] .text : 0xc0100000 - 0xc02ba293 (1768 kB) >> [ 0.004000] Checking if this processor honours the WP bit even in >> supervisor mode...Ok. >> [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated >> [ 0.084214] Calibrating delay using timer specific routine.. 1802.45 >> BogoMIPS (lpj=3604919) >> [ 0.084287] Security Framework initialized >> [ 0.084298] SELinux: Disabled at boot. >> [ 0.084308] Capability LSM initialized >> [ 0.084334] Mount-cache hash table entries: 512 >> [ 0.084609] Initializing cgroup subsys ns >> [ 0.084617] Initializing cgroup subsys cpuacct >> [ 0.084622] Initializing cgroup subsys devices >> [ 0.084660] CPU: L1 I cache: 32K, L1 D cache: 32K >> [ 0.084666] CPU: L2 cache: 512K >> [ 0.084674] Intel machine check architecture supported. >> [ 0.084682] Intel machine check reporting enabled on CPU#0. >> [ 0.084705] Checking 'hlt' instruction... OK. >> [ 0.100731] SMP alternatives: switching to UP code >> [ 0.110392] Freeing SMP alternatives: 16k freed >> [ 0.110398] ACPI: Core revision 20080321 >> [ 0.124464] ACPI: setting ELCR to 0200 (from 0ca8) >> [ 0.132008] CPU0: Intel(R) Celeron(R) M processor 900MHz >> stepping 08 >> [ 0.132008] APIC calibration not consistent with PM Timer: 136ms >> instead of 100ms >> [ 0.132008] APIC delta adjusted to PM-Timer: 625063 (850136) >> [ 0.132008] Brought up 1 CPUs >> [ 0.132008] Total of 1 processors activated (1802.45 BogoMIPS). >> [ 0.132008] CPU0 attaching sched-domain: >> [ 0.132008] domain 0: span 0 >> [ 0.132008] groups: 0 >> [ 0.132008] net_namespace: 660 bytes >> [ 0.132008] Booting paravirtualized kernel on bare hardware >> [ 0.132008] NET: Registered protocol family 16 >> [ 0.132008] ACPI: bus type pci registered >> [ 0.132008] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 >> - 255 >> [ 0.132008] PCI: Not using MMCONFIG. >> [ 0.132008] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5 >> [ 0.132008] PCI: Using configuration type 1 for base access >> [ 0.132008] Setting up standard PCI resources >> [ 0.144009] ACPI: EC: Look up EC in DSDT >> [ 0.159346] ACPI: Interpreter enabled >> [ 0.159352] ACPI: (supports S0 S1 S3 S4 S5) >> [ 0.159388] ACPI: Using PIC for interrupt routing >> [ 0.159511] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 >> - 255 >> [ 0.162710] PCI: MCFG area at e0000000 reserved in ACPI motherboard >> resources >> [ 0.162716] PCI: Using MMCONFIG for extended config space >> [ 0.173511] ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62 >> [ 0.173518] ACPI: EC: driver started in poll mode >> [ 0.173755] ACPI: PCI Root Bridge [PCI0] (0000:00) >> [ 0.174621] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 >> [ 0.174633] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 >> ACPI/GPIO/TCO >> [ 0.174640] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO >> [ 0.175178] PCI: Transparent bridge - 0000:00:1e.0 >> [ 0.175222] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] >> [ 0.175798] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT] >> [ 0.175995] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT] >> [ 0.176243] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT] >> [ 0.184710] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 >> 14 15) >> [ 0.184978] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 >> 14 15) >> [ 0.185241] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 >> 14 15) >> [ 0.185500] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 >> 14 15) >> [ 0.185763] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 >> 15) *0, disabled. >> [ 0.186025] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 >> 15) *0, disabled. >> [ 0.186287] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 >> 15) *0, disabled. >> [ 0.186548] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 >> 14 15) >> [ 0.186882] Linux Plug and Play Support v0.97 (c) Adam Belay >> [ 0.186950] pnp: PnP ACPI init >> [ 0.186965] ACPI: bus type pnp registered >> [ 0.191275] pnp: PnP ACPI: found 13 devices >> [ 0.191282] ACPI: ACPI bus type pnp unregistered >> [ 0.191292] PnPBIOS: Disabled by ACPI PNP >> [ 0.191792] PCI: Using ACPI for IRQ routing >> [ 0.192357] hpet clockevent registered >> [ 0.192369] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 >> [ 0.192377] hpet0: 3 64-bit timers, 14318180 Hz >> [ 0.193456] ACPI: RTC can wake from S4 >> [ 0.193513] system 00:01: iomem range 0xfed13000-0xfed19fff has been >> reserved >> [ 0.193534] system 00:08: ioport range 0x380-0x383 has been reserved >> [ 0.193540] system 00:08: ioport range 0x4d0-0x4d1 has been reserved >> [ 0.193546] system 00:08: ioport range 0x800-0x87f has been reserved >> [ 0.193552] system 00:08: ioport range 0x480-0x4bf has been reserved >> [ 0.193559] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been >> reserved >> [ 0.193565] system 00:08: iomem range 0xfed20000-0xfed8ffff has been >> reserved >> [ 0.193572] system 00:08: iomem range 0xfff00000-0xffffffff could not >> be reserved >> [ 0.193584] system 00:09: iomem range 0xfec00000-0xfec00fff has been >> reserved >> [ 0.193590] system 00:09: iomem range 0xfee00000-0xfee00fff could not >> be reserved >> [ 0.193602] system 00:0a: iomem range 0xe0000000-0xefffffff has been >> reserved >> [ 0.193614] system 00:0b: iomem range 0xe0000000-0xefffffff has been >> reserved >> [ 0.193631] system 00:0c: iomem range 0x0-0x9ffff could not be reserved >> [ 0.193638] system 00:0c: iomem range 0xe0000-0xfffff could not be >> reserved >> [ 0.193644] system 00:0c: iomem range 0x100000-0x3f7fffff could not be >> reserved >> [ 0.224415] PCI: Bridge: 0000:00:1c.0 >> [ 0.224420] IO window: disabled. >> [ 0.224427] MEM window: disabled. >> [ 0.224433] PREFETCH window: disabled. >> [ 0.224441] PCI: Bridge: 0000:00:1c.1 >> [ 0.224444] IO window: disabled. >> [ 0.224451] MEM window: 0xfbf00000-0xfbffffff >> [ 0.224457] PREFETCH window: disabled. >> [ 0.224465] PCI: Bridge: 0000:00:1c.2 >> [ 0.224468] IO window: disabled. >> [ 0.224475] MEM window: 0xf8000000-0xfbefffff >> [ 0.224482] PREFETCH window: 0x00000000f0000000-0x00000000f6ffffff >> [ 0.224491] PCI: Bridge: 0000:00:1e.0 >> [ 0.224494] IO window: disabled. >> [ 0.224500] MEM window: disabled. >> [ 0.224505] PREFETCH window: disabled. >> [ 0.224872] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5 >> [ 0.224878] PCI: setting IRQ 5 as level-triggered >> [ 0.224884] ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 5 >> (level, low) -> IRQ 5 >> [ 0.224896] PCI: Setting latency timer of device 0000:00:1c.0 to 64 >> [ 0.225204] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 >> [ 0.225209] PCI: setting IRQ 11 as level-triggered >> [ 0.225215] ACPI: PCI Interrupt 0000:00:1c.1[B] -> Link [LNKB] -> GSI >> 11 (level, low) -> IRQ 11 >> [ 0.225226] PCI: Setting latency timer of device 0000:00:1c.1 to 64 >> [ 0.225528] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 >> [ 0.225533] PCI: setting IRQ 10 as level-triggered >> [ 0.225539] ACPI: PCI Interrupt 0000:00:1c.2[C] -> Link [LNKC] -> GSI >> 10 (level, low) -> IRQ 10 >> [ 0.225549] PCI: Setting latency timer of device 0000:00:1c.2 to 64 >> [ 0.225564] PCI: Setting latency timer of device 0000:00:1e.0 to 64 >> [ 0.225608] NET: Registered protocol family 2 >> [ 0.225794] IP route cache hash table entries: 32768 (order: 5, 131072 >> bytes) >> [ 0.226219] TCP established hash table entries: 131072 (order: 8, >> 1048576 bytes) >> [ 0.227867] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) >> [ 0.228708] TCP: Hash tables configured (established 131072 bind 65536) >> [ 0.228716] TCP reno registered >> [ 0.228952] NET: Registered protocol family 1 >> [ 0.229175] checking if image is initramfs...<7>Switched to high >> resolution mode on CPU 0 >> [ 0.718795] it is >> [ 1.253276] Freeing initrd memory: 5802k freed >> [ 1.254324] audit: initializing netlink socket (disabled) >> [ 1.254352] type=2000 audit(1232394730.252:1): initialized >> [ 1.254614] highmem bounce pool size: 64 pages >> [ 1.254625] Total HugeTLB memory allocated, 0 >> [ 1.254763] VFS: Disk quotas dquot_6.5.1 >> [ 1.254815] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >> [ 1.254881] msgmni has been set to 1767 >> [ 1.255090] Block layer SCSI generic (bsg) driver version 0.4 loaded >> (major 253) >> [ 1.255096] io scheduler noop registered >> [ 1.255101] io scheduler anticipatory registered >> [ 1.255105] io scheduler deadline registered >> [ 1.255130] io scheduler cfq registered (default) >> [ 1.255155] pci 0000:00:02.0: Boot video device >> [ 1.255428] PCI: Setting latency timer of device 0000:00:1c.0 to 64 >> [ 1.255470] assign_interrupt_mode Found MSI capability >> [ 1.255513] Allocate Port Service[0000:00:1c.0:pcie00] >> [ 1.255593] Allocate Port Service[0000:00:1c.0:pcie02] >> [ 1.255663] Allocate Port Service[0000:00:1c.0:pcie03] >> [ 1.255788] PCI: Setting latency timer of device 0000:00:1c.1 to 64 >> [ 1.255827] assign_interrupt_mode Found MSI capability >> [ 1.255867] Allocate Port Service[0000:00:1c.1:pcie00] >> [ 1.255942] Allocate Port Service[0000:00:1c.1:pcie02] >> [ 1.256010] Allocate Port Service[0000:00:1c.1:pcie03] >> [ 1.256157] PCI: Setting latency timer of device 0000:00:1c.2 to 64 >> [ 1.256198] assign_interrupt_mode Found MSI capability >> [ 1.256237] Allocate Port Service[0000:00:1c.2:pcie00] >> [ 1.256310] Allocate Port Service[0000:00:1c.2:pcie02] >> [ 1.256379] Allocate Port Service[0000:00:1c.2:pcie03] >> [ 1.256929] isapnp: Scanning for PnP cards... >> [ 1.610708] isapnp: No Plug & Play device found >> [ 1.615603] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ >> sharing enabled >> [ 1.619389] brd: module loaded >> [ 1.619573] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at >> 0x60,0x64 irq 1,12 >> [ 1.654990] serio: i8042 KBD port at 0x60,0x64 irq 1 >> [ 1.655000] serio: i8042 AUX port at 0x60,0x64 irq 12 >> [ 1.655304] mice: PS/2 mouse device common for all mice >> [ 1.656447] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 >> [ 1.656447] rtc0: alarms up to one month >> [ 1.656447] cpuidle: using governor ladder >> [ 1.656447] cpuidle: using governor menu >> [ 1.656447] No iBFT detected. >> [ 1.656447] TCP cubic registered >> [ 1.656447] NET: Registered protocol family 17 >> [ 1.656447] Using IPI No-Shortcut mode >> [ 1.656447] registered taskstats version 1 >> [ 1.656447] rtc_cmos 00:03: setting system clock to 2009-01-19 19:52:11 >> UTC (1232394731) >> [ 1.656447] Freeing unused kernel memory: 244k freed >> [ 1.679754] input: AT Translated Set 2 keyboard as /class/input/input0 >> [ 1.830264] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) >> [ 1.830360] ACPI: ACPI0007:00 is registered as cooling_device0 >> [ 1.830368] ACPI: Processor [CPU1] (supports 8 throttling states) >> [ 1.834937] ACPI: EC: non-query interrupt received, switching to >> interrupt mode >> [ 1.835020] Marking TSC unstable due to: TSC halts in idle. >> [ 2.023282] ACPI: LNXTHERM:01 is registered as thermal_zone0 >> [ 2.030790] ACPI: Thermal Zone [TZ00] (62 C) >> [ 2.192033] Clocksource tsc unstable (delta = -195791138 ns) >> [ 3.165517] usbcore: registered new interface driver usbfs >> [ 3.165566] usbcore: registered new interface driver hub >> [ 3.165634] usbcore: registered new device driver usb >> [ 3.178277] USB Universal Host Controller Interface driver v3.0 >> [ 3.178707] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3 >> [ 3.178713] PCI: setting IRQ 3 as level-triggered >> [ 3.178720] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 3 >> (level, low) -> IRQ 3 >> [ 3.178736] PCI: Setting latency timer of device 0000:00:1d.0 to 64 >> [ 3.178745] uhci_hcd 0000:00:1d.0: UHCI Host Controller >> [ 3.178937] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus >> number 1 >> [ 3.178974] uhci_hcd 0000:00:1d.0: irq 3, io base 0x0000e400 >> [ 3.179123] usb usb1: configuration #1 chosen from 1 choice >> [ 3.179176] hub 1-0:1.0: USB hub found >> [ 3.179188] hub 1-0:1.0: 2 ports detected >> [ 3.280222] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 >> [ 3.280231] usb usb1: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [ 3.280236] usb usb1: Product: UHCI Host Controller >> [ 3.280241] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd >> [ 3.280245] usb usb1: SerialNumber: 0000:00:1d.0 >> [ 3.280668] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7 >> [ 3.280674] PCI: setting IRQ 7 as level-triggered >> [ 3.280680] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 7 >> (level, low) -> IRQ 7 >> [ 3.280699] PCI: Setting latency timer of device 0000:00:1d.1 to 64 >> [ 3.280705] uhci_hcd 0000:00:1d.1: UHCI Host Controller >> [ 3.280755] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus >> number 2 >> [ 3.280789] uhci_hcd 0000:00:1d.1: irq 7, io base 0x0000e480 >> [ 3.280928] usb usb2: configuration #1 chosen from 1 choice >> [ 3.280983] hub 2-0:1.0: USB hub found >> [ 3.280997] hub 2-0:1.0: 2 ports detected >> [ 3.281906] No dock devices found. >> [ 3.352371] SCSI subsystem initialized >> [ 3.384238] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 >> [ 3.384246] usb usb2: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [ 3.384252] usb usb2: Product: UHCI Host Controller >> [ 3.384256] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd >> [ 3.384261] usb usb2: SerialNumber: 0000:00:1d.1 >> [ 3.384330] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI >> 10 (level, low) -> IRQ 10 >> [ 3.384347] PCI: Setting latency timer of device 0000:00:1d.2 to 64 >> [ 3.384354] uhci_hcd 0000:00:1d.2: UHCI Host Controller >> [ 3.384399] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus >> number 3 >> [ 3.384433] uhci_hcd 0000:00:1d.2: irq 10, io base 0x0000e800 >> [ 3.384577] usb usb3: configuration #1 chosen from 1 choice >> [ 3.384629] hub 3-0:1.0: USB hub found >> [ 3.384640] hub 3-0:1.0: 2 ports detected >> [ 3.416319] libata version 3.00 loaded. >> [ 3.488204] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 >> [ 3.488212] usb usb3: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [ 3.488218] usb usb3: Product: UHCI Host Controller >> [ 3.488223] usb usb3: Manufacturer: Linux 2.6.26-1-686 uhci_hcd >> [ 3.488227] usb usb3: SerialNumber: 0000:00:1d.2 >> [ 3.488303] ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 5 >> (level, low) -> IRQ 5 >> [ 3.488320] PCI: Setting latency timer of device 0000:00:1d.3 to 64 >> [ 3.488327] uhci_hcd 0000:00:1d.3: UHCI Host Controller >> [ 3.488378] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus >> number 4 >> [ 3.488413] uhci_hcd 0000:00:1d.3: irq 5, io base 0x0000e880 >> [ 3.488560] usb usb4: configuration #1 chosen from 1 choice >> [ 3.488612] hub 4-0:1.0: USB hub found >> [ 3.488625] hub 4-0:1.0: 2 ports detected >> [ 3.592215] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 >> [ 3.592223] usb usb4: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [ 3.592229] usb usb4: Product: UHCI Host Controller >> [ 3.592234] usb usb4: Manufacturer: Linux 2.6.26-1-686 uhci_hcd >> [ 3.592238] usb usb4: SerialNumber: 0000:00:1d.3 >> [ 3.593865] ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 3 >> (level, low) -> IRQ 3 >> [ 3.593890] PCI: Setting latency timer of device 0000:00:1d.7 to 64 >> [ 3.593897] ehci_hcd 0000:00:1d.7: EHCI Host Controller >> [ 3.593962] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus >> number 5 >> [ 3.597887] ehci_hcd 0000:00:1d.7: debug port 1 >> [ 3.597896] PCI: cache line size of 32 is not supported by device >> 0000:00:1d.7 >> [ 3.597911] ehci_hcd 0000:00:1d.7: irq 3, io mem 0xf7eb7c00 >> [ 3.624100] usb 2-1: new low speed USB device using uhci_hcd and address 2 >> [ 3.636034] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver >> 10 Dec 2004 >> [ 3.636195] usb usb5: configuration #1 chosen from 1 choice >> [ 3.636252] hub 5-0:1.0: USB hub found >> [ 3.636267] hub 5-0:1.0: 8 ports detected >> [ 3.692091] hub 2-0:1.0: unable to enumerate USB device on port 1 >> [ 3.740226] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 >> [ 3.740234] usb usb5: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [ 3.740240] usb usb5: Product: EHCI Host Controller >> [ 3.740244] usb usb5: Manufacturer: Linux 2.6.26-1-686 ehci_hcd >> [ 3.740249] usb usb5: SerialNumber: 0000:00:1d.7 >> [ 3.740783] ahci 0000:00:1f.2: version 3.0 >> [ 3.740819] ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 7 >> (level, low) -> IRQ 7 >> [ 3.740844] ACPI: PCI interrupt for device 0000:00:1f.2 disabled >> [ 3.740856] ahci: probe of 0000:00:1f.2 failed with error -22 >> [ 3.745573] ata_piix 0000:00:1f.2: version 2.12 >> [ 3.745593] ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 7 >> (level, low) -> IRQ 7 >> [ 3.745603] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] >> [ 3.745666] PCI: Setting latency timer of device 0000:00:1f.2 to 64 >> [ 3.745758] scsi0 : ata_piix >> [ 3.745903] scsi1 : ata_piix >> [ 3.749073] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 >> irq 14 >> [ 3.749080] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 >> irq 15 >> [ 4.092738] ata2.00: ATA-5: ASUS-PHISON OB SSD, TST2.04U, max UDMA/66 >> [ 4.092746] ata2.00: 7880544 sectors, multi 0: LBA >> [ 4.092784] ata2.01: ATA-5: ASUS-PHISON SSD, TST2.04P, max UDMA/66 >> [ 4.092789] ata2.01: 31522176 sectors, multi 0: LBA >> [ 4.100659] ata2.00: configured for UDMA/66 >> [ 4.108633] ata2.01: configured for UDMA/66 >> [ 4.108817] scsi 1:0:0:0: Direct-Access ATA ASUS-PHISON OB S >> TST2 PQ: 0 ANSI: 5 >> [ 4.109109] scsi 1:0:1:0: Direct-Access ATA ASUS-PHISON SSD >> TST2 PQ: 0 ANSI: 5 >> [ 4.126696] Uniform Multi-Platform E-IDE driver >> [ 4.126708] ide: Assuming 33MHz system bus speed for PIO modes; >> override with idebus=xx >> [ 4.196148] Driver 'sd' needs updating - please use bus_type methods >> [ 4.196314] sd 1:0:0:0: [sda] 7880544 512-byte hardware sectors (4035 MB) >> [ 4.196348] sd 1:0:0:0: [sda] Write Protect is off >> [ 4.196353] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 >> [ 4.196409] sd 1:0:0:0: [sda] Write cache: disabled, read cache: >> enabled, doesn't support DPO or FUA >> [ 4.196525] sd 1:0:0:0: [sda] 7880544 512-byte hardware sectors (4035 MB) >> [ 4.196556] sd 1:0:0:0: [sda] Write Protect is off >> [ 4.196563] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 >> [ 4.196618] sd 1:0:0:0: [sda] Write cache: disabled, read cache: >> enabled, doesn't support DPO or FUA >> [ 4.196625] sda: sda1 >> [ 4.198512] sd 1:0:0:0: [sda] Attached SCSI disk >> [ 4.198653] sd 1:0:1:0: [sdb] 31522176 512-byte hardware sectors (16139 >> MB) >> [ 4.198687] sd 1:0:1:0: [sdb] Write Protect is off >> [ 4.198693] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00 >> [ 4.198747] sd 1:0:1:0: [sdb] Write cache: disabled, read cache: >> enabled, doesn't support DPO or FUA >> [ 4.198847] sd 1:0:1:0: [sdb] 31522176 512-byte hardware sectors (16139 >> MB) >> [ 4.198878] sd 1:0:1:0: [sdb] Write Protect is off >> [ 4.198884] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00 >> [ 4.198937] sd 1:0:1:0: [sdb] Write cache: disabled, read cache: >> enabled, doesn't support DPO or FUA >> [ 4.198945] sdb: sdb1 sdb2 < sdb5 > >> [ 4.201758] sd 1:0:1:0: [sdb] Attached SCSI disk >> [ 4.392601] PM: Starting manual resume from disk >> [ 4.425481] kjournald starting. Commit interval 5 seconds >> [ 4.425500] EXT3-fs: mounted filesystem with ordered data mode. >> [ 4.744055] usb 5-5: new high speed USB device using ehci_hcd and >> address 4 >> [ 4.877440] usb 5-5: configuration #1 chosen from 1 choice >> [ 4.877868] usb 5-5: New USB device found, idVendor=0951, idProduct=1606 >> [ 4.877875] usb 5-5: New USB device strings: Mfr=1, Product=2, >> SerialNumber=4 >> [ 4.877880] usb 5-5: Product: UB6225 >> [ 4.877884] usb 5-5: Manufacturer: ENE >> [ 4.877888] usb 5-5: SerialNumber: 146030377350 >> [ 5.116092] usb 5-8: new high speed USB device using ehci_hcd and >> address 5 >> [ 5.128576] udevd version 125 started >> [ 5.663525] usb 5-8: configuration #1 chosen from 1 choice >> [ 5.665432] usb 5-8: New USB device found, idVendor=05e3, idProduct=0505 >> [ 5.665440] usb 5-8: New USB device strings: Mfr=0, Product=1, >> SerialNumber=0 >> [ 5.665445] usb 5-8: Product: USB 2.0 Camera >> [ 5.904061] usb 2-1: new low speed USB device using uhci_hcd and address 3 >> [ 6.078974] usb 2-1: configuration #1 chosen from 1 choice >> [ 6.092113] usb 2-1: New USB device found, idVendor=093a, idProduct=2510 >> [ 6.092121] usb 2-1: New USB device strings: Mfr=1, Product=2, >> SerialNumber=0 >> [ 6.092127] usb 2-1: Product: USB OPTICAL MOUSE >> [ 6.092131] usb 2-1: Manufacturer: PIXART >> [ 6.332049] usb 2-2: new full speed USB device using uhci_hcd and >> address 4 >> [ 6.452049] usb 2-2: device descriptor read/64, error -71 >> [ 6.676048] usb 2-2: device descriptor read/64, error -71 >> [ 6.892049] usb 2-2: new full speed USB device using uhci_hcd and >> address 5 >> [ 7.012056] usb 2-2: device descriptor read/64, error -71 >> [ 7.184041] Linux agpgart interface v0.103 >> [ 7.217692] agpgart: Detected an Intel 915GM Chipset. >> [ 7.217903] agpgart: Detected 7932K stolen memory. >> [ 7.238885] agpgart: AGP aperture is 256M @ 0xd0000000 >> [ 7.238965] usb 2-2: device descriptor read/64, error -71 >> [ 7.452044] usb 2-2: new full speed USB device using uhci_hcd and >> address 6 >> [ 7.860027] usb 2-2: device not accepting address 6, error -71 >> [ 7.864253] Atheros(R) L2 Ethernet Driver - version 2.0.5 >> [ 7.864259] Copyright (c) 2007 Atheros Corporation. >> [ 7.864320] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKB] -> GSI >> 11 (level, low) -> IRQ 11 >> [ 7.864339] PCI: Setting latency timer of device 0000:03:00.0 to 64 >> [ 7.972048] usb 2-2: new full speed USB device using uhci_hcd and >> address 7 >> [ 8.153587] ath_hal: module license 'Proprietary' taints kernel. >> [ 8.176070] AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, >> RF5413, RF2133, RF2425, RF2417) >> [ 8.179523] eeepc: Eee PC Hotkey Driver >> [ 8.179764] eeepc: Hotkey init flags 0x41 >> [ 8.181034] eeepc: Get control methods supported: 0x101711 >> [ 8.189538] input: Power Button (FF) as /class/input/input1 >> [ 8.216368] ACPI: Power Button (FF) [PWRF] >> [ 8.216521] input: Lid Switch as /class/input/input2 >> [ 8.245309] ACPI: Lid Switch [LID] >> [ 8.245427] input: Sleep Button (CM) as /class/input/input3 >> [ 8.275834] ACPI: Sleep Button (CM) [SLPB] >> [ 8.275940] input: Power Button (CM) as /class/input/input4 >> [ 8.303486] ACPI: Power Button (CM) [PWRB] >> [ 8.384026] usb 2-2: device not accepting address 7, error -71 >> [ 8.384135] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 8.550914] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKC] -> GSI >> 10 (level, low) -> IRQ 10 >> [ 8.550934] PCI: Setting latency timer of device 0000:01:00.0 to 64 >> [ 9.042244] MadWifi: ath_attach: Switching rfkill capability off. >> [ 9.735124] ACPI: AC Adapter [AC0] (on-line) >> [ 10.756737] ACPI: EC: missing confirmations, switch off interrupt mode. >> [ 11.208450] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) >> [ 11.208577] iTCO_wdt: Found a ICH6-M TCO device (Version=2, >> TCOBASE=0x0860) >> [ 11.208620] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) >> [ 11.477769] ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> GSI 5 >> (level, low) -> IRQ 5 >> [ 11.477805] PCI: Setting latency timer of device 0000:00:1b.0 to 64 >> [ 11.483562] input: PC Speaker as /class/input/input5 >> [ 11.501902] hda_codec: Unknown model for ALC662, trying auto-probe from >> BIOS... >> [ 11.540394] ACPI: Battery Slot [BAT0] (battery present) >> [ 11.541343] input: Video Bus as /class/input/input6 >> [ 11.548119] intel_rng: FWH not detected >> [ 11.568109] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) >> [ 12.410100] Initializing USB Mass Storage driver... >> [ 12.410257] scsi2 : SCSI emulation for USB Mass Storage devices >> [ 12.410408] usbcore: registered new interface driver usb-storage >> [ 12.410415] USB Mass Storage support registered. >> [ 12.419980] usb-storage: device found at 4 >> [ 12.419987] usb-storage: waiting for device to settle before scanning >> [ 12.467956] Linux video capture interface: v2.00 >> [ 12.501378] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (05e3:0505) >> [ 12.675603] usbcore: registered new interface driver uvcvideo >> [ 12.675612] USB Video Class driver (v0.1.0) >> [ 12.690664] usbcore: registered new interface driver hiddev >> [ 12.706770] input: PIXART USB OPTICAL MOUSE as /class/input/input7 >> [ 12.732114] input,hidraw0: USB HID v1.10 Mouse [PIXART USB OPTICAL >> MOUSE] on usb-0000:00:1d.1-1 >> [ 12.732155] usbcore: registered new interface driver usbhid >> [ 12.732161] usbhid: v2.6:USB HID core driver >> [ 13.367766] wifi0: Atheros AR2425 chip found (MAC 14.2, PHY SChip 7.0, >> Radio 10.2) >> [ 13.491684] ath_pci: wifi0: Atheros 5424/2424: mem=0xfbef0000, irq=10 >> [ 13.493167] ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKD] -> GSI 7 >> (level, low) -> IRQ 7 >> [ 14.103195] input: ImPS/2 Logitech Wheel Mouse as /class/input/input8 >> [ 14.612235] Adding 706820k swap on /dev/sdb5. Priority:-1 extents:1 >> across:706820k >> [ 14.741005] EXT3 FS on sdb1, internal journal >> [ 15.148504] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 >> [ 15.156599] pciehp: HPC vendor_id 8086 device_id 2660 ss_vid 0 ss_did 0 >> [ 15.156711] Load service driver hpdriver on pcie device >> 0000:00:1c.0:pcie02 >> [ 15.156733] pciehp: HPC vendor_id 8086 device_id 2662 ss_vid 0 ss_did 0 >> [ 16.160089] pciehp: Device 0000:03:00.0 already exists at 3:0, cannot >> hot-add >> [ 16.160202] pciehp: Cannot add device 0x3:0 >> [ 17.164098] Load service driver hpdriver on pcie device >> 0000:00:1c.1:pcie02 >> [ 17.164136] pciehp: HPC vendor_id 8086 device_id 2664 ss_vid 0 ss_did 0 >> [ 17.416293] usb-storage: device scan complete >> [ 17.416756] scsi 2:0:0:0: Direct-Access USB2.0 CardReader SD0 >> 0100 PQ: 0 ANSI: 0 >> [ 17.418374] sd 2:0:0:0: [sdc] Attached SCSI removable disk >> [ 18.168064] pciehp: Device 0000:01:00.0 already exists at 1:0, cannot >> hot-add >> [ 18.168156] pciehp: Cannot add device 0x1:0 >> [ 19.172058] Load service driver hpdriver on pcie device >> 0000:00:1c.2:pcie02 >> [ 19.172108] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 >> [ 32.817916] lp: driver loaded but no devices found >> [ 32.878596] ppdev: user-space parallel port driver >> [ 33.353445] NET: Registered protocol family 10 >> [ 33.354326] lo: Disabled Privacy Extensions >> [ 33.355270] ADDRCONF(NETDEV_UP): eth0: link is not ready >> [ 34.573246] warning: `avahi-daemon' uses 32-bit capabilities (legacy >> support in use) >> [ 43.156412] Bluetooth: Core ver 2.11 >> [ 43.158622] NET: Registered protocol family 31 >> [ 43.158632] Bluetooth: HCI device and connection manager initialized >> [ 43.158638] Bluetooth: HCI socket layer initialized >> [ 43.235432] Bluetooth: L2CAP ver 2.9 >> [ 43.235441] Bluetooth: L2CAP socket layer initialized >> [ 43.311284] Bluetooth: RFCOMM socket layer initialized >> [ 43.311306] Bluetooth: RFCOMM TTY layer initialized >> [ 43.311310] Bluetooth: RFCOMM ver 1.8 >> [ 49.437113] [drm] Initialized drm 1.1.0 20060810 >> [ 50.574435] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 5 >> (level, low) -> IRQ 5 >> [ 50.574454] PCI: Setting latency timer of device 0000:00:02.0 to 64 >> [ 50.574592] [drm] Initialized i915 1.6.0 20060119 on minor 0 >> [ 95.536152] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready >> [ 111.140013] ath0: no IPv6 routers present >> [ 321.816064] usb 2-2: new full speed USB device using uhci_hcd and >> address 8 >> [ 321.872078] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 323.056069] usb 2-2: new full speed USB device using uhci_hcd and >> address 9 >> [ 323.198730] usb 2-2: device descriptor read/all, error -71 >> [ 323.256090] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 324.296074] usb 2-2: new full speed USB device using uhci_hcd and >> address 11 >> [ 324.352091] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 325.536036] usb 2-2: new full speed USB device using uhci_hcd and >> address 12 >> [ 325.686747] usb 2-2: unable to read config index 0 descriptor/all >> [ 325.686747] usb 2-2: can't read configurations, error -71 >> [ 325.744091] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 326.776039] usb 2-2: new full speed USB device using uhci_hcd and >> address 14 >> [ 326.832092] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 328.016070] usb 2-2: new full speed USB device using uhci_hcd and >> address 15 >> [ 328.072161] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 329.256077] usb 2-2: new full speed USB device using uhci_hcd and >> address 16 >> [ 329.312097] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 330.496075] usb 2-2: new full speed USB device using uhci_hcd and >> address 17 >> [ 330.552108] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 331.736069] usb 2-2: new full speed USB device using uhci_hcd and >> address 18 >> [ 331.878747] usb 2-2: device descriptor read/all, error -71 >> [ 331.936095] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 332.976078] usb 2-2: new full speed USB device using uhci_hcd and >> address 20 >> [ 333.118668] usb 2-2: device descriptor read/all, error -71 >> [ 333.176108] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 334.216075] usb 2-2: new full speed USB device using uhci_hcd and >> address 22 >> [ 334.272108] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 335.456137] usb 2-2: new full speed USB device using uhci_hcd and >> address 23 >> [ 335.512118] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 336.696071] usb 2-2: new full speed USB device using uhci_hcd and >> address 24 >> [ 336.838739] usb 2-2: device descriptor read/all, error -71 >> [ 336.896067] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 337.936069] usb 2-2: new full speed USB device using uhci_hcd and >> address 26 >> [ 337.992105] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 339.176075] usb 2-2: new full speed USB device using uhci_hcd and >> address 27 >> [ 339.236097] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 340.416067] usb 2-2: new full speed USB device using uhci_hcd and >> address 28 >> [ 340.476107] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 341.656078] usb 2-2: new full speed USB device using uhci_hcd and >> address 29 >> [ 341.827652] usb 2-2: configuration #1 chosen from 1 choice >> [ 341.833292] usb 2-2: can't set config #1, error -71 >> [ 341.833436] usb 2-2: New USB device found, idVendor=04d8, idProduct=000a >> [ 341.833443] usb 2-2: New USB device strings: Mfr=1, Product=2, >> SerialNumber=3 >> [ 341.833468] usb 2-2: USB disconnect, address 29 >> [ 342.896078] usb 2-2: new full speed USB device using uhci_hcd and >> address 30 >> [ 342.952095] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 344.136074] usb 2-2: new full speed USB device using uhci_hcd and >> address 31 >> [ 344.192112] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 345.376075] usb 2-2: new full speed USB device using uhci_hcd and >> address 32 >> [ 345.436065] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 346.616073] usb 2-2: new full speed USB device using uhci_hcd and >> address 33 >> [ 346.758870] usb 2-2: device descriptor read/all, error -71 >> [ 346.816090] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 347.856079] usb 2-2: new full speed USB device using uhci_hcd and >> address 35 >> [ 347.998741] usb 2-2: device descriptor read/all, error -71 >> [ 348.056093] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 349.096073] usb 2-2: new full speed USB device using uhci_hcd and >> address 37 >> [ 349.246504] usb 2-2: unable to read config index 0 descriptor/all >> [ 349.246504] usb 2-2: can't read configurations, error -71 >> [ 349.304144] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 350.336071] usb 2-2: new full speed USB device using uhci_hcd and >> address 39 >> [ 350.486581] usb 2-2: unable to read config index 0 descriptor/all >> [ 350.486581] usb 2-2: can't read configurations, error -71 >> [ 350.544097] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 351.576075] usb 2-2: new full speed USB device using uhci_hcd and >> address 41 >> [ 351.729542] usb 2-2: unable to read config index 0 descriptor/all >> [ 351.729542] usb 2-2: can't read configurations, error -71 >> [ 351.784099] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 352.816067] usb 2-2: new full speed USB device using uhci_hcd and >> address 43 >> [ 352.872105] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 354.056173] usb 2-2: new full speed USB device using uhci_hcd and >> address 44 >> [ 354.198756] usb 2-2: device descriptor read/all, error -71 >> [ 354.256102] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 355.296075] usb 2-2: new full speed USB device using uhci_hcd and >> address 46 >> [ 355.446516] usb 2-2: unable to read config index 0 descriptor/all >> [ 355.446516] usb 2-2: can't read configurations, error -71 >> [ 355.504102] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 356.536041] usb 2-2: new full speed USB device using uhci_hcd and >> address 48 >> [ 356.686702] usb 2-2: unable to read config index 0 descriptor/all >> [ 356.686702] usb 2-2: can't read configurations, error -71 >> [ 356.744059] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 357.776045] usb 2-2: new full speed USB device using uhci_hcd and >> address 50 >> [ 357.926582] usb 2-2: unable to read config index 0 descriptor/all >> [ 357.926582] usb 2-2: can't read configurations, error -71 >> [ 357.984071] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 359.016069] usb 2-2: new full speed USB device using uhci_hcd and >> address 52 >> [ 359.072171] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 360.256077] usb 2-2: new full speed USB device using uhci_hcd and >> address 53 >> [ 360.316100] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 361.496046] usb 2-2: new full speed USB device using uhci_hcd and >> address 54 >> [ 361.646872] usb 2-2: unable to read config index 0 descriptor/all >> [ 361.646883] usb 2-2: can't read configurations, error -71 >> [ 361.704071] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 362.736071] usb 2-2: new full speed USB device using uhci_hcd and >> address 56 >> [ 362.878746] usb 2-2: device descriptor read/all, error -71 >> [ 362.936069] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 363.976081] usb 2-2: new full speed USB device using uhci_hcd and >> address 58 >> [ 364.032099] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 365.216069] usb 2-2: new full speed USB device using uhci_hcd and >> address 59 >> [ 365.361850] usb 2-2: device descriptor read/all, error -71 >> [ 365.416095] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 366.456076] usb 2-2: new full speed USB device using uhci_hcd and >> address 61 >> [ 366.512099] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 367.696078] usb 2-2: new full speed USB device using uhci_hcd and >> address 62 >> [ 367.838690] usb 2-2: device descriptor read/all, error -71 >> [ 367.896101] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 368.936044] usb 2-2: new full speed USB device using uhci_hcd and >> address 64 >> [ 368.992106] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 370.176080] usb 2-2: new full speed USB device using uhci_hcd and >> address 65 >> [ 370.232103] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 371.416073] usb 2-2: new full speed USB device using uhci_hcd and >> address 66 >> [ 371.472106] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 372.656082] usb 2-2: new full speed USB device using uhci_hcd and >> address 67 >> [ 372.712103] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 373.896080] usb 2-2: new full speed USB device using uhci_hcd and >> address 68 >> [ 374.045624] usb 2-2: unable to read config index 0 descriptor/start: -71 >> [ 374.045624] usb 2-2: chopping to 0 config(s) >> [ 374.053868] usb 2-2: string descriptor 0 read error: -71 >> [ 374.061828] usb 2-2: string descriptor 0 read error: -71 >> [ 374.069525] usb 2-2: string descriptor 0 read error: -71 >> [ 374.069525] usb 2-2: no configuration chosen from 0 choices >> [ 374.069525] usb 2-2: New USB device found, idVendor=04d8, idProduct=000a >> [ 374.069525] usb 2-2: New USB device strings: Mfr=1, Product=2, >> SerialNumber=3 >> [ 374.069525] usb 2-2: USB disconnect, address 68 >> [ 375.136075] usb 2-2: new full speed USB device using uhci_hcd and >> address 69 >> [ 375.192110] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 376.376083] usb 2-2: new full speed USB device using uhci_hcd and >> address 70 >> [ 376.432100] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 377.616075] usb 2-2: new full speed USB device using uhci_hcd and >> address 71 >> [ 377.767653] usb 2-2: unable to read config index 0 descriptor/all >> [ 377.767653] usb 2-2: can't read configurations, error -71 >> [ 377.824096] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 378.856084] usb 2-2: new full speed USB device using uhci_hcd and >> address 73 >> [ 378.912074] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 380.096078] usb 2-2: new full speed USB device using uhci_hcd and >> address 74 >> [ 380.246755] usb 2-2: unable to read config index 0 descriptor/all >> [ 380.246755] usb 2-2: can't read configurations, error -71 >> [ 380.304106] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 381.336075] usb 2-2: new full speed USB device using uhci_hcd and >> address 76 >> [ 381.392112] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 382.576042] usb 2-2: new full speed USB device using uhci_hcd and >> address 77 >> [ 382.718749] usb 2-2: device descriptor read/all, error -71 >> [ 382.776103] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 383.816074] usb 2-2: new full speed USB device using uhci_hcd and >> address 79 >> [ 383.966777] usb 2-2: unable to read config index 0 descriptor/all >> [ 383.966777] usb 2-2: can't read configurations, error -71 >> [ 384.024099] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 385.056078] usb 2-2: new full speed USB device using uhci_hcd and >> address 81 >> [ 385.112104] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 386.296083] usb 2-2: new full speed USB device using uhci_hcd and >> address 82 >> [ 386.352162] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 387.536079] usb 2-2: new full speed USB device using uhci_hcd and >> address 83 >> [ 387.592105] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 388.776083] usb 2-2: new full speed USB device using uhci_hcd and >> address 84 >> [ 388.926509] usb 2-2: unable to read config index 0 descriptor/all >> [ 388.926509] usb 2-2: can't read configurations, error -71 >> [ 388.984109] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 390.016074] usb 2-2: new full speed USB device using uhci_hcd and >> address 86 >> [ 390.158884] usb 2-2: device descriptor read/all, error -71 >> [ 390.216060] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 391.256077] usb 2-2: new full speed USB device using uhci_hcd and >> address 88 >> [ 391.406576] usb 2-2: unable to read config index 0 descriptor/all >> [ 391.406576] usb 2-2: can't read configurations, error -71 >> [ 391.464106] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 392.496156] usb 2-2: new full speed USB device using uhci_hcd and >> address 90 >> [ 392.552101] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 393.736084] usb 2-2: new full speed USB device using uhci_hcd and >> address 91 >> [ 393.792110] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 394.976043] usb 2-2: new full speed USB device using uhci_hcd and >> address 92 >> [ 395.121683] usb 2-2: device descriptor read/all, error -71 >> [ 395.176103] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 396.216038] usb 2-2: new full speed USB device using uhci_hcd and >> address 94 >> [ 396.366761] usb 2-2: unable to read config index 0 descriptor/all >> [ 396.366762] usb 2-2: can't read configurations, error -71 >> [ 396.424065] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 397.456073] usb 2-2: new full speed USB device using uhci_hcd and >> address 96 >> [ 397.606587] usb 2-2: unable to read config index 0 descriptor/all >> [ 397.606587] usb 2-2: can't read configurations, error -71 >> [ 397.664109] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 398.696080] usb 2-2: new full speed USB device using uhci_hcd and >> address 98 >> [ 398.838747] usb 2-2: device descriptor read/all, error -71 >> [ 398.896068] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 399.936072] usb 2-2: new full speed USB device using uhci_hcd and >> address 100 >> [ 400.085736] usb 2-2: unable to read config index 0 descriptor/start: -71 >> [ 400.085736] usb 2-2: chopping to 0 config(s) >> [ 400.093874] usb 2-2: string descriptor 0 read error: -71 >> [ 400.101757] usb 2-2: string descriptor 0 read error: -71 >> [ 400.109490] usb 2-2: string descriptor 0 read error: -71 >> [ 400.109490] usb 2-2: no configuration chosen from 0 choices >> [ 400.109490] usb 2-2: New USB device found, idVendor=04d8, idProduct=000a >> [ 400.109490] usb 2-2: New USB device strings: Mfr=1, Product=2, >> SerialNumber=3 >> [ 400.109490] usb 2-2: USB disconnect, address 100 >> [ 401.176045] usb 2-2: new full speed USB device using uhci_hcd and >> address 101 >> [ 401.232064] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 402.416082] usb 2-2: new full speed USB device using uhci_hcd and >> address 102 >> [ 402.472111] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 403.656082] usb 2-2: new full speed USB device using uhci_hcd and >> address 103 >> [ 403.712103] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 404.896044] usb 2-2: new full speed USB device using uhci_hcd and >> address 104 >> [ 404.952098] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 406.136072] usb 2-2: new full speed USB device using uhci_hcd and >> address 105 >> [ 406.192107] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 407.376078] usb 2-2: new full speed USB device using uhci_hcd and >> address 106 >> [ 407.432115] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 408.616099] usb 2-2: new full speed USB device using uhci_hcd and >> address 107 >> [ 408.766762] usb 2-2: unable to read config index 0 descriptor/all >> [ 408.766762] usb 2-2: can't read configurations, error -71 >> [ 408.824118] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 409.856084] usb 2-2: new full speed USB device using uhci_hcd and >> address 109 >> [ 409.912132] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 411.096048] usb 2-2: new full speed USB device using uhci_hcd and >> address 110 >> [ 411.245982] usb 2-2: unable to read config index 0 descriptor/all >> [ 411.245982] usb 2-2: can't read configurations, error -71 >> [ 411.304077] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 412.336053] usb 2-2: new full speed USB device using uhci_hcd and >> address 112 >> [ 412.392081] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 413.576055] usb 2-2: new full speed USB device using uhci_hcd and >> address 113 >> [ 413.632078] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 414.816046] usb 2-2: new full speed USB device using uhci_hcd and >> address 114 >> [ 414.872082] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 416.056052] usb 2-2: new full speed USB device using uhci_hcd and >> address 115 >> [ 416.207055] usb 2-2: unable to read config index 0 descriptor/all >> [ 416.207055] usb 2-2: can't read configurations, error -71 >> [ 416.264080] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 417.296046] usb 2-2: new full speed USB device using uhci_hcd and >> address 117 >> [ 417.446150] usb 2-2: unable to read config index 0 descriptor/all >> [ 417.446150] usb 2-2: can't read configurations, error -71 >> [ 417.504136] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 418.536048] usb 2-2: new full speed USB device using uhci_hcd and >> address 119 >> [ 418.686768] usb 2-2: unable to read config index 0 descriptor/all >> [ 418.686768] usb 2-2: can't read configurations, error -71 >> [ 418.744077] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 419.776055] usb 2-2: new full speed USB device using uhci_hcd and >> address 121 >> [ 419.832073] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 421.016049] usb 2-2: new full speed USB device using uhci_hcd and >> address 122 >> [ 421.072088] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 422.256049] usb 2-2: new full speed USB device using uhci_hcd and >> address 123 >> [ 422.398770] usb 2-2: device descriptor read/all, error -71 >> [ 422.456076] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 423.496051] usb 2-2: new full speed USB device using uhci_hcd and >> address 125 >> [ 423.646900] usb 2-2: unable to read config index 0 descriptor/all >> [ 423.646914] usb 2-2: can't read configurations, error -71 >> [ 423.704075] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 424.736046] usb 2-2: new full speed USB device using uhci_hcd and >> address 127 >> [ 424.886764] usb 2-2: unable to read config index 0 descriptor/all >> [ 424.886778] usb 2-2: can't read configurations, error -71 >> [ 424.944071] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 425.976048] usb 2-2: new full speed USB device using uhci_hcd and >> address 4 >> [ 426.121685] usb 2-2: device descriptor read/all, error -71 >> [ 426.176082] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 427.216049] usb 2-2: new full speed USB device using uhci_hcd and >> address 6 >> [ 427.272083] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 428.456049] usb 2-2: new full speed USB device using uhci_hcd and >> address 7 >> [ 428.512072] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 429.696049] usb 2-2: new full speed USB device using uhci_hcd and >> address 8 >> [ 429.752079] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 430.936052] usb 2-2: new full speed USB device using uhci_hcd and >> address 9 >> [ 431.086733] usb 2-2: unable to read config index 0 descriptor/all >> [ 431.086733] usb 2-2: can't read configurations, error -71 >> [ 431.144075] hub 2-0:1.0: unable to enumerate USB device on port 2 >> [ 432.176055] usb 2-2: new full speed USB device using uhci_hcd and >> address 11 >> [ 432.318826] usb 2-2: device descriptor read/all, error -71 >> [ 432.376080] hub 2-0:1.0: unable to enumerate USB device on port 2 >> >> lsmod -v: >> Module Size Used by >> wlan_ccmp 6496 2 >> i915 25280 2 >> drm 65256 3 i915 >> rfcomm 28272 0 >> l2cap 17248 5 rfcomm >> bluetooth 44900 4 rfcomm,l2cap >> ipv6 235300 14 >> ppdev 6468 0 >> parport_pc 22500 0 >> lp 8164 0 >> parport 30988 3 ppdev,parport_pc,lp >> cpufreq_powersave 1856 0 >> cpufreq_stats 3776 0 >> cpufreq_userspace 3172 0 >> cpufreq_ondemand 6476 0 >> cpufreq_conservative 5960 0 >> freq_table 4224 2 cpufreq_stats,cpufreq_ondemand >> cdc_acm 12224 0 >> pciehp 28540 0 >> pci_hotplug 23460 1 pciehp >> wlan_scan_sta 11296 1 >> usbhid 35904 0 >> hid 33184 1 usbhid >> ff_memless 4392 1 usbhid >> uvcvideo 45704 0 >> compat_ioctl32 1312 1 uvcvideo >> videodev 27520 1 uvcvideo >> v4l1_compat 12260 2 uvcvideo,videodev >> usb_storage 75936 0 >> serio_raw 4740 0 >> psmouse 32336 0 >> rng_core 3940 0 >> pcspkr 2432 0 >> i2c_i801 7920 0 >> snd_hda_intel 324248 1 >> i2c_core 19828 1 i2c_i801 >> snd_pcm_oss 32800 0 >> snd_pcm 62596 2 snd_hda_intel,snd_pcm_oss >> iTCO_wdt 9508 0 >> snd_mixer_oss 12320 1 snd_pcm_oss >> video 16432 0 >> output 2912 1 video >> battery 10180 0 >> snd_seq_dummy 2660 0 >> ac 4196 0 >> ath_rate_sample 11104 1 >> ath_pci 202712 0 >> eeepc_laptop 7440 0 >> button 6096 0 >> wlan 194000 5 >> wlan_ccmp,wlan_scan_sta,ath_rate_sample,ath_pci >> ath_hal 300768 3 ath_rate_sample,ath_pci >> atl2 22744 0 >> snd_seq_oss 24992 0 >> snd_seq_midi_event 6432 1 snd_seq_oss >> snd_seq 41456 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event >> snd_timer 17800 2 snd_pcm,snd_seq >> snd_seq_device 6380 3 snd_seq_dummy,snd_seq_oss,snd_seq >> snd 45604 10 >> snd_hda_intel,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_seq_oss,snd_seq,snd_timer,snd_seq_device >> intel_agp 22332 1 >> agpgart 28776 3 drm,intel_agp >> soundcore 6368 1 snd >> snd_page_alloc 7816 2 snd_hda_intel,snd_pcm >> evdev 8000 6 >> ext3 105512 1 >> jbd 39444 1 ext3 >> mbcache 7108 1 ext3 >> sd_mod 22200 3 >> ide_pci_generic 3908 0 [permanent] >> ide_core 96168 1 ide_pci_generic >> ata_generic 4676 0 >> ata_piix 14180 2 >> ahci 23176 0 >> libata 140384 3 ata_generic,ata_piix,ahci >> scsi_mod 129356 3 usb_storage,sd_mod,libata >> dock 8304 1 libata >> ehci_hcd 28428 0 >> uhci_hcd 18672 0 >> usbcore 118160 7 >> cdc_acm,usbhid,uvcvideo,usb_storage,ehci_hcd,uhci_hcd >> thermal 15228 0 >> processor 32576 2 thermal >> fan 4164 0 >> thermal_sys 10856 4 video,thermal,processor,fan >> >> lspci: >> 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express >> Processor to DRAM Controller (rev 04) >> Subsystem: ASUSTeK Computer Inc. Device 82d9 >> Flags: bus master, fast devsel, latency 0 >> Capabilities: [e0] Vendor Specific Information <?> >> Kernel driver in use: agpgart-intel >> Kernel modules: intel-agp >> >> 00:02.0 VGA compatible controller: Intel Corporation Mobile >> 915GM/GMS/910GML Express Graphics Controller (rev 04) (prog-if 00 [VGA >> controller]) >> Subsystem: ASUSTeK Computer Inc. Device 82d9 >> Flags: bus master, fast devsel, latency 0, IRQ 16 >> Memory at f7f00000 (32-bit, non-prefetchable) [size=512K] >> I/O ports at ec00 [size=8] >> Memory at d0000000 (32-bit, prefetchable) [size=256M] >> Memory at f7ec0000 (32-bit, non-prefetchable) [size=256K] >> Capabilities: [d0] Power Management version 2 >> Kernel modules: intelfb >> >> 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML >> Express Graphics Controller (rev 04) >> Subsystem: ASUSTeK Computer Inc. Device 82d9 >> Flags: bus master, fast devsel, latency 0 >> Memory at f7f80000 (32-bit, non-prefetchable) [size=512K] >> Capabilities: [d0] Power Management version 2 >> >> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 >> Family) High Definition Audio Controller (rev 04) >> Subsystem: ASUSTeK Computer Inc. Device 8337 >> Flags: bus master, fast devsel, latency 0, IRQ 16 >> Memory at f7eb8000 (64-bit, non-prefetchable) [size=16K] >> Capabilities: [50] Power Management version 2 >> Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 >> Enable- >> Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 >> Capabilities: [100] Virtual Channel <?> >> Capabilities: [130] Root Complex Link <?> >> Kernel driver in use: HDA Intel >> Kernel modules: snd-hda-intel >> >> 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) >> PCI Express Port 1 (rev 04) (prog-if 00 [Normal decode]) >> Flags: bus master, fast devsel, latency 0 >> Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 >> Capabilities: [40] Express Root Port (Slot+), MSI 00 >> Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 >> Enable+ >> Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Capabilities: [a0] Power Management version 2 >> Capabilities: [100] Virtual Channel <?> >> Capabilities: [180] Root Complex Link <?> >> Kernel driver in use: pcieport-driver >> Kernel modules: shpchp >> >> 00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) >> PCI Express Port 2 (rev 04) (prog-if 00 [Normal decode]) >> Flags: bus master, fast devsel, latency 0 >> Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 >> Memory behind bridge: fbf00000-fbffffff >> Capabilities: [40] Express Root Port (Slot+), MSI 00 >> Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 >> Enable+ >> Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Capabilities: [a0] Power Management version 2 >> Capabilities: [100] Virtual Channel <?> >> Capabilities: [180] Root Complex Link <?> >> Kernel driver in use: pcieport-driver >> Kernel modules: shpchp >> >> 00:1c.2 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) >> PCI Express Port 3 (rev 04) (prog-if 00 [Normal decode]) >> Flags: bus master, fast devsel, latency 0 >> Bus: primary=00, secondary=01, subordinate=02, sec-latency=0 >> Memory behind bridge: f8000000-fbefffff >> Prefetchable memory behind bridge: 00000000f0000000-00000000f6ffffff >> Capabilities: [40] Express Root Port (Slot+), MSI 00 >> Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 >> Enable+ >> Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Capabilities: [a0] Power Management version 2 >> Capabilities: [100] Virtual Channel <?> >> Capabilities: [180] Root Complex Link <?> >> Kernel driver in use: pcieport-driver >> Kernel modules: shpchp >> >> 00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 >> Family) USB UHCI #1 (rev 04) (prog-if 00 [UHCI]) >> Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Flags: bus master, medium devsel, latency 0, IRQ 23 >> I/O ports at e400 [size=32] >> Kernel driver in use: uhci_hcd >> Kernel modules: uhci-hcd >> >> 00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 >> Family) USB UHCI #2 (rev 04) (prog-if 00 [UHCI]) >> Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Flags: bus master, medium devsel, latency 0, IRQ 19 >> I/O ports at e480 [size=32] >> Kernel driver in use: uhci_hcd >> Kernel modules: uhci-hcd >> >> 00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 >> Family) USB UHCI #3 (rev 04) (prog-if 00 [UHCI]) >> Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Flags: bus master, medium devsel, latency 0, IRQ 18 >> I/O ports at e800 [size=32] >> Kernel driver in use: uhci_hcd >> Kernel modules: uhci-hcd >> >> 00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 >> Family) USB UHCI #4 (rev 04) (prog-if 00 [UHCI]) >> Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Flags: bus master, medium devsel, latency 0, IRQ 16 >> I/O ports at e880 [size=32] >> Kernel driver in use: uhci_hcd >> Kernel modules: uhci-hcd >> >> 00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 >> Family) USB2 EHCI Controller (rev 04) (prog-if 20 [EHCI]) >> Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Flags: bus master, medium devsel, latency 0, IRQ 23 >> Memory at f7eb7c00 (32-bit, non-prefetchable) [size=1K] >> Capabilities: [50] Power Management version 2 >> Capabilities: [58] Debug port: BAR=1 offset=00a0 >> Kernel driver in use: ehci_hcd >> Kernel modules: ehci-hcd >> >> 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4) >> (prog-if 01 [Subtractive decode]) >> Flags: bus master, fast devsel, latency 0 >> Bus: primary=00, secondary=05, subordinate=05, sec-latency=32 >> Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device 82d8 >> >> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface >> Bridge (rev 04) >> Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Flags: bus master, medium devsel, latency 0 >> Kernel modules: intel-rng, iTCO_wdt >> >> 00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller >> (rev 04) (prog-if 80 [Master]) >> Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19 >> I/O ports at 01f0 [size=8] >> I/O ports at 03f4 [size=1] >> I/O ports at 0170 [size=8] >> I/O ports at 0374 [size=1] >> I/O ports at ffa0 [size=16] >> Capabilities: [70] Power Management version 2 >> Kernel driver in use: ata_piix >> Kernel modules: ahci, ata_piix >> >> 00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus >> Controller (rev 04) >> Subsystem: ASUSTeK Computer Inc. Device 82d8 >> Flags: medium devsel, IRQ 19 >> I/O ports at 0400 [size=32] >> Kernel driver in use: i801_smbus >> Kernel modules: i2c-i801 >> >> 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg >> Wireless PCI Express Adapter (rev 01) >> Subsystem: Device 1a3b:1026 >> Flags: bus master, fast devsel, latency 0, IRQ 18 >> Memory at fbef0000 (64-bit, non-prefetchable) [size=64K] >> Capabilities: [40] Power Management version 2 >> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 >> Enable- >> Capabilities: [60] Express Legacy Endpoint, MSI 00 >> Capabilities: [90] MSI-X: Enable- Mask- TabSize=1 >> Capabilities: [100] Advanced Error Reporting <?> >> Capabilities: [140] Virtual Channel <?> >> Kernel driver in use: ath_pci >> Kernel modules: ath_pci, ath5k >> >> 03:00.0 Ethernet controller: Attansic Technology Corp. L2 100 Mbit >> Ethernet Adapter (rev a0) >> Subsystem: ASUSTeK Computer Inc. Device 8233 >> Flags: bus master, fast devsel, latency 0, IRQ 220 >> Memory at fbfc0000 (64-bit, non-prefetchable) [size=256K] >> Expansion ROM at fbfa0000 [disabled] [size=128K] >> Capabilities: [40] Power Management version 2 >> Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 >> Enable+ >> Capabilities: [58] Express Endpoint, MSI 00 >> Capabilities: [6c] Vital Product Data <?> >> Capabilities: [100] Advanced Error Reporting <?> >> Kernel driver in use: atl2 >> Kernel modules: atl2 >> >> >> Any suggestion is very welcome. >> Thanks. >> Wim >> >> >> >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-usb" in >> the body of a message to majordomo@xxxxxxxxxxxxxxx >> More majordomo info at http://vger.kernel.org/majordomo-info.html >> > > > > > -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
