Hi, you seem to have a few USB devices connected, have you tried using an externally powered USB HUB? Tony Olech Elan Digital Systems On Tue, 2009-01-20 at 17:25 +0100, Wim de Vries wrote: > Hi, > I am trying to connect an USB device to my asus eee pc. > The device connects OK on my HP compaq 6910p with Suse 10.3: > dmesg: > usb 7-1: new full speed USB device using uhci_hcd and address 4 > usb 7-1: new device found, idVendor=04d8, idProduct=000a > usb 7-1: new device strings: Mfr=1, Product=2, SerialNumber=3 > usb 7-1: Product: PIC18 USB CDC > usb 7-1: Manufacturer: Microchip > usb 7-1: SerialNumber: V1.1FS > usb 7-1: configuration #1 chosen from 1 choice > drivers/usb/class/cdc-acm.c: This device cannot do calls on its own. It > is no; modem. > cdc_acm 7-1:1.0: ttyACM0: USB ACM device > > So it should ánd can use cdc-acm. > > Nevertheless, on the asus (kernel version: 2.6.26-1-686, Debian,KDE): > > dmesg: > [ 0.000000] Initializing cgroup subsys cpuset > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-11) > (waldi@xxxxxxxxxx) (gcc version 4.1.3 20080623 (prerelease) (Debian > 4.1.2-23)) #1 SMP Wed Nov 26 19:14:11 UTC 2008 > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) > [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f780000 (usable) > [ 0.000000] BIOS-e820: 000000003f780000 - 000000003f790000 (ACPI data) > [ 0.000000] BIOS-e820: 000000003f790000 - 000000003f7d0000 (ACPI NVS) > [ 0.000000] BIOS-e820: 000000003f7d0000 - 000000003f7de000 (reserved) > [ 0.000000] BIOS-e820: 000000003f7e0000 - 000000003f800000 (reserved) > [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) > [ 0.000000] 119MB HIGHMEM available. > [ 0.000000] 896MB LOWMEM available. > [ 0.000000] found SMP MP-table at [c00ff780] 000ff780 > [ 0.000000] Entering add_active_range(0, 0, 259968) 0 entries of 256 used > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0 -> 4096 > [ 0.000000] Normal 4096 -> 229376 > [ 0.000000] HighMem 229376 -> 259968 > [ 0.000000] Movable zone start PFN for each node > [ 0.000000] early_node_map[1] active PFN ranges > [ 0.000000] 0: 0 -> 259968 > [ 0.000000] On node 0 totalpages: 259968 > [ 0.000000] DMA zone: 32 pages used for memmap > [ 0.000000] DMA zone: 0 pages reserved > [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 > [ 0.000000] Normal zone: 1760 pages used for memmap > [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 > [ 0.000000] HighMem zone: 239 pages used for memmap > [ 0.000000] HighMem zone: 30353 pages, LIFO batch:7 > [ 0.000000] Movable zone: 0 pages used for memmap > [ 0.000000] DMI present. > [ 0.000000] ACPI: RSDP 000FBE60, 0014 (r0 ACPIAM) > [ 0.000000] ACPI: RSDT 3F780000, 0034 (r1 A M I OEMRSDT 9000811 MSFT > 97) > [ 0.000000] ACPI: FACP 3F780200, 0081 (r1 A M I OEMFACP 9000811 MSFT > 97) > [ 0.000000] ACPI: DSDT 3F780400, 6109 (r1 A0979 A0979034 34 INTL > 20060113) > [ 0.000000] ACPI: FACS 3F790000, 0040 > [ 0.000000] ACPI: APIC 3F780390, 0068 (r1 A M I OEMAPIC 9000811 MSFT > 97) > [ 0.000000] ACPI: OEMB 3F790040, 0046 (r1 A M I AMI_OEM 9000811 MSFT > 97) > [ 0.000000] ACPI: MCFG 3F786510, 003C (r1 A M I OEMMCFG 9000811 MSFT > 97) > [ 0.000000] ACPI: PM-Timer IO Port: 0x808 > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > [ 0.000000] ACPI: Skipping IOAPIC probe due to 'noapic' option. > [ 0.000000] Using ACPI for processor (LAPIC) configuration information > [ 0.000000] Intel MultiProcessor Specification v1.4 > [ 0.000000] Virtual Wire compatibility mode. > [ 0.000000] MPTABLE: OEM ID: INTEL Product ID: <6>MPTABLE: Product > ID: <6>MPTABLE: APIC at: 0xFEE00000 > [ 0.000000] I/O APIC #1 Version 32 at 0xFEC00000. > [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs > [ 0.000000] Processors: 1 > [ 0.000000] Allocating PCI resources starting at 40000000 (gap: > 3f800000:bf600000) > [ 0.000000] PM: Registered nosave memory: 000000000009f000 - > 00000000000a0000 > [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - > 00000000000e4000 > [ 0.000000] PM: Registered nosave memory: 00000000000e4000 - > 0000000000100000 > [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs > [ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data > [ 0.000000] NR_CPUS: 8, nr_cpu_ids: 1 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. > Total pages: 257937 > [ 0.000000] Kernel command line: root=/dev/sdb1 ro quiet noapic > [ 0.000000] mapped APIC to ffffb000 (fee00000) > [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) > [ 0.000000] Enabling fast FPU save and restore... done. > [ 0.000000] Enabling unmasked SIMD FPU exception support... done. > [ 0.000000] Initializing CPU#0 > [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) > [ 0.000000] Detected 900.130 MHz processor. > [ 0.004000] Console: colour VGA+ 80x25 > [ 0.004000] console [tty0] enabled > [ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 > bytes) > [ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) > [ 0.004000] Memory: 1021104k/1039872k available (1768k kernel code, > 18032k reserved, 752k data, 244k init, 122368k highmem) > [ 0.004000] virtual kernel memory layout: > [ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB) > [ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) > [ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) > [ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) > [ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB) > [ 0.004000] .data : 0xc02ba293 - 0xc0376620 ( 752 kB) > [ 0.004000] .text : 0xc0100000 - 0xc02ba293 (1768 kB) > [ 0.004000] Checking if this processor honours the WP bit even in > supervisor mode...Ok. > [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated > [ 0.084214] Calibrating delay using timer specific routine.. 1802.45 > BogoMIPS (lpj=3604919) > [ 0.084287] Security Framework initialized > [ 0.084298] SELinux: Disabled at boot. > [ 0.084308] Capability LSM initialized > [ 0.084334] Mount-cache hash table entries: 512 > [ 0.084609] Initializing cgroup subsys ns > [ 0.084617] Initializing cgroup subsys cpuacct > [ 0.084622] Initializing cgroup subsys devices > [ 0.084660] CPU: L1 I cache: 32K, L1 D cache: 32K > [ 0.084666] CPU: L2 cache: 512K > [ 0.084674] Intel machine check architecture supported. > [ 0.084682] Intel machine check reporting enabled on CPU#0. > [ 0.084705] Checking 'hlt' instruction... OK. > [ 0.100731] SMP alternatives: switching to UP code > [ 0.110392] Freeing SMP alternatives: 16k freed > [ 0.110398] ACPI: Core revision 20080321 > [ 0.124464] ACPI: setting ELCR to 0200 (from 0ca8) > [ 0.132008] CPU0: Intel(R) Celeron(R) M processor 900MHz > stepping 08 > [ 0.132008] APIC calibration not consistent with PM Timer: 136ms > instead of 100ms > [ 0.132008] APIC delta adjusted to PM-Timer: 625063 (850136) > [ 0.132008] Brought up 1 CPUs > [ 0.132008] Total of 1 processors activated (1802.45 BogoMIPS). > [ 0.132008] CPU0 attaching sched-domain: > [ 0.132008] domain 0: span 0 > [ 0.132008] groups: 0 > [ 0.132008] net_namespace: 660 bytes > [ 0.132008] Booting paravirtualized kernel on bare hardware > [ 0.132008] NET: Registered protocol family 16 > [ 0.132008] ACPI: bus type pci registered > [ 0.132008] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 > - 255 > [ 0.132008] PCI: Not using MMCONFIG. > [ 0.132008] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5 > [ 0.132008] PCI: Using configuration type 1 for base access > [ 0.132008] Setting up standard PCI resources > [ 0.144009] ACPI: EC: Look up EC in DSDT > [ 0.159346] ACPI: Interpreter enabled > [ 0.159352] ACPI: (supports S0 S1 S3 S4 S5) > [ 0.159388] ACPI: Using PIC for interrupt routing > [ 0.159511] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 > - 255 > [ 0.162710] PCI: MCFG area at e0000000 reserved in ACPI motherboard > resources > [ 0.162716] PCI: Using MMCONFIG for extended config space > [ 0.173511] ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62 > [ 0.173518] ACPI: EC: driver started in poll mode > [ 0.173755] ACPI: PCI Root Bridge [PCI0] (0000:00) > [ 0.174621] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 > [ 0.174633] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 > ACPI/GPIO/TCO > [ 0.174640] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO > [ 0.175178] PCI: Transparent bridge - 0000:00:1e.0 > [ 0.175222] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > [ 0.175798] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT] > [ 0.175995] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT] > [ 0.176243] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT] > [ 0.184710] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 > 14 15) > [ 0.184978] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 > 14 15) > [ 0.185241] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 > 14 15) > [ 0.185500] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 > 14 15) > [ 0.185763] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 > 15) *0, disabled. > [ 0.186025] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 > 15) *0, disabled. > [ 0.186287] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 > 15) *0, disabled. > [ 0.186548] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 > 14 15) > [ 0.186882] Linux Plug and Play Support v0.97 (c) Adam Belay > [ 0.186950] pnp: PnP ACPI init > [ 0.186965] ACPI: bus type pnp registered > [ 0.191275] pnp: PnP ACPI: found 13 devices > [ 0.191282] ACPI: ACPI bus type pnp unregistered > [ 0.191292] PnPBIOS: Disabled by ACPI PNP > [ 0.191792] PCI: Using ACPI for IRQ routing > [ 0.192357] hpet clockevent registered > [ 0.192369] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 > [ 0.192377] hpet0: 3 64-bit timers, 14318180 Hz > [ 0.193456] ACPI: RTC can wake from S4 > [ 0.193513] system 00:01: iomem range 0xfed13000-0xfed19fff has been > reserved > [ 0.193534] system 00:08: ioport range 0x380-0x383 has been reserved > [ 0.193540] system 00:08: ioport range 0x4d0-0x4d1 has been reserved > [ 0.193546] system 00:08: ioport range 0x800-0x87f has been reserved > [ 0.193552] system 00:08: ioport range 0x480-0x4bf has been reserved > [ 0.193559] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been > reserved > [ 0.193565] system 00:08: iomem range 0xfed20000-0xfed8ffff has been > reserved > [ 0.193572] system 00:08: iomem range 0xfff00000-0xffffffff could not > be reserved > [ 0.193584] system 00:09: iomem range 0xfec00000-0xfec00fff has been > reserved > [ 0.193590] system 00:09: iomem range 0xfee00000-0xfee00fff could not > be reserved > [ 0.193602] system 00:0a: iomem range 0xe0000000-0xefffffff has been > reserved > [ 0.193614] system 00:0b: iomem range 0xe0000000-0xefffffff has been > reserved > [ 0.193631] system 00:0c: iomem range 0x0-0x9ffff could not be reserved > [ 0.193638] system 00:0c: iomem range 0xe0000-0xfffff could not be > reserved > [ 0.193644] system 00:0c: iomem range 0x100000-0x3f7fffff could not be > reserved > [ 0.224415] PCI: Bridge: 0000:00:1c.0 > [ 0.224420] IO window: disabled. > [ 0.224427] MEM window: disabled. > [ 0.224433] PREFETCH window: disabled. > [ 0.224441] PCI: Bridge: 0000:00:1c.1 > [ 0.224444] IO window: disabled. > [ 0.224451] MEM window: 0xfbf00000-0xfbffffff > [ 0.224457] PREFETCH window: disabled. > [ 0.224465] PCI: Bridge: 0000:00:1c.2 > [ 0.224468] IO window: disabled. > [ 0.224475] MEM window: 0xf8000000-0xfbefffff > [ 0.224482] PREFETCH window: 0x00000000f0000000-0x00000000f6ffffff > [ 0.224491] PCI: Bridge: 0000:00:1e.0 > [ 0.224494] IO window: disabled. > [ 0.224500] MEM window: disabled. > [ 0.224505] PREFETCH window: disabled. > [ 0.224872] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5 > [ 0.224878] PCI: setting IRQ 5 as level-triggered > [ 0.224884] ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 5 > (level, low) -> IRQ 5 > [ 0.224896] PCI: Setting latency timer of device 0000:00:1c.0 to 64 > [ 0.225204] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 > [ 0.225209] PCI: setting IRQ 11 as level-triggered > [ 0.225215] ACPI: PCI Interrupt 0000:00:1c.1[B] -> Link [LNKB] -> GSI > 11 (level, low) -> IRQ 11 > [ 0.225226] PCI: Setting latency timer of device 0000:00:1c.1 to 64 > [ 0.225528] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 > [ 0.225533] PCI: setting IRQ 10 as level-triggered > [ 0.225539] ACPI: PCI Interrupt 0000:00:1c.2[C] -> Link [LNKC] -> GSI > 10 (level, low) -> IRQ 10 > [ 0.225549] PCI: Setting latency timer of device 0000:00:1c.2 to 64 > [ 0.225564] PCI: Setting latency timer of device 0000:00:1e.0 to 64 > [ 0.225608] NET: Registered protocol family 2 > [ 0.225794] IP route cache hash table entries: 32768 (order: 5, 131072 > bytes) > [ 0.226219] TCP established hash table entries: 131072 (order: 8, > 1048576 bytes) > [ 0.227867] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) > [ 0.228708] TCP: Hash tables configured (established 131072 bind 65536) > [ 0.228716] TCP reno registered > [ 0.228952] NET: Registered protocol family 1 > [ 0.229175] checking if image is initramfs...<7>Switched to high > resolution mode on CPU 0 > [ 0.718795] it is > [ 1.253276] Freeing initrd memory: 5802k freed > [ 1.254324] audit: initializing netlink socket (disabled) > [ 1.254352] type=2000 audit(1232394730.252:1): initialized > [ 1.254614] highmem bounce pool size: 64 pages > [ 1.254625] Total HugeTLB memory allocated, 0 > [ 1.254763] VFS: Disk quotas dquot_6.5.1 > [ 1.254815] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 1.254881] msgmni has been set to 1767 > [ 1.255090] Block layer SCSI generic (bsg) driver version 0.4 loaded > (major 253) > [ 1.255096] io scheduler noop registered > [ 1.255101] io scheduler anticipatory registered > [ 1.255105] io scheduler deadline registered > [ 1.255130] io scheduler cfq registered (default) > [ 1.255155] pci 0000:00:02.0: Boot video device > [ 1.255428] PCI: Setting latency timer of device 0000:00:1c.0 to 64 > [ 1.255470] assign_interrupt_mode Found MSI capability > [ 1.255513] Allocate Port Service[0000:00:1c.0:pcie00] > [ 1.255593] Allocate Port Service[0000:00:1c.0:pcie02] > [ 1.255663] Allocate Port Service[0000:00:1c.0:pcie03] > [ 1.255788] PCI: Setting latency timer of device 0000:00:1c.1 to 64 > [ 1.255827] assign_interrupt_mode Found MSI capability > [ 1.255867] Allocate Port Service[0000:00:1c.1:pcie00] > [ 1.255942] Allocate Port Service[0000:00:1c.1:pcie02] > [ 1.256010] Allocate Port Service[0000:00:1c.1:pcie03] > [ 1.256157] PCI: Setting latency timer of device 0000:00:1c.2 to 64 > [ 1.256198] assign_interrupt_mode Found MSI capability > [ 1.256237] Allocate Port Service[0000:00:1c.2:pcie00] > [ 1.256310] Allocate Port Service[0000:00:1c.2:pcie02] > [ 1.256379] Allocate Port Service[0000:00:1c.2:pcie03] > [ 1.256929] isapnp: Scanning for PnP cards... > [ 1.610708] isapnp: No Plug & Play device found > [ 1.615603] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ > sharing enabled > [ 1.619389] brd: module loaded > [ 1.619573] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at > 0x60,0x64 irq 1,12 > [ 1.654990] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 1.655000] serio: i8042 AUX port at 0x60,0x64 irq 12 > [ 1.655304] mice: PS/2 mouse device common for all mice > [ 1.656447] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 > [ 1.656447] rtc0: alarms up to one month > [ 1.656447] cpuidle: using governor ladder > [ 1.656447] cpuidle: using governor menu > [ 1.656447] No iBFT detected. > [ 1.656447] TCP cubic registered > [ 1.656447] NET: Registered protocol family 17 > [ 1.656447] Using IPI No-Shortcut mode > [ 1.656447] registered taskstats version 1 > [ 1.656447] rtc_cmos 00:03: setting system clock to 2009-01-19 19:52:11 > UTC (1232394731) > [ 1.656447] Freeing unused kernel memory: 244k freed > [ 1.679754] input: AT Translated Set 2 keyboard as /class/input/input0 > [ 1.830264] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > [ 1.830360] ACPI: ACPI0007:00 is registered as cooling_device0 > [ 1.830368] ACPI: Processor [CPU1] (supports 8 throttling states) > [ 1.834937] ACPI: EC: non-query interrupt received, switching to > interrupt mode > [ 1.835020] Marking TSC unstable due to: TSC halts in idle. > [ 2.023282] ACPI: LNXTHERM:01 is registered as thermal_zone0 > [ 2.030790] ACPI: Thermal Zone [TZ00] (62 C) > [ 2.192033] Clocksource tsc unstable (delta = -195791138 ns) > [ 3.165517] usbcore: registered new interface driver usbfs > [ 3.165566] usbcore: registered new interface driver hub > [ 3.165634] usbcore: registered new device driver usb > [ 3.178277] USB Universal Host Controller Interface driver v3.0 > [ 3.178707] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3 > [ 3.178713] PCI: setting IRQ 3 as level-triggered > [ 3.178720] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 3 > (level, low) -> IRQ 3 > [ 3.178736] PCI: Setting latency timer of device 0000:00:1d.0 to 64 > [ 3.178745] uhci_hcd 0000:00:1d.0: UHCI Host Controller > [ 3.178937] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus > number 1 > [ 3.178974] uhci_hcd 0000:00:1d.0: irq 3, io base 0x0000e400 > [ 3.179123] usb usb1: configuration #1 chosen from 1 choice > [ 3.179176] hub 1-0:1.0: USB hub found > [ 3.179188] hub 1-0:1.0: 2 ports detected > [ 3.280222] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 > [ 3.280231] usb usb1: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 3.280236] usb usb1: Product: UHCI Host Controller > [ 3.280241] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd > [ 3.280245] usb usb1: SerialNumber: 0000:00:1d.0 > [ 3.280668] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7 > [ 3.280674] PCI: setting IRQ 7 as level-triggered > [ 3.280680] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 7 > (level, low) -> IRQ 7 > [ 3.280699] PCI: Setting latency timer of device 0000:00:1d.1 to 64 > [ 3.280705] uhci_hcd 0000:00:1d.1: UHCI Host Controller > [ 3.280755] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus > number 2 > [ 3.280789] uhci_hcd 0000:00:1d.1: irq 7, io base 0x0000e480 > [ 3.280928] usb usb2: configuration #1 chosen from 1 choice > [ 3.280983] hub 2-0:1.0: USB hub found > [ 3.280997] hub 2-0:1.0: 2 ports detected > [ 3.281906] No dock devices found. > [ 3.352371] SCSI subsystem initialized > [ 3.384238] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 > [ 3.384246] usb usb2: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 3.384252] usb usb2: Product: UHCI Host Controller > [ 3.384256] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd > [ 3.384261] usb usb2: SerialNumber: 0000:00:1d.1 > [ 3.384330] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI > 10 (level, low) -> IRQ 10 > [ 3.384347] PCI: Setting latency timer of device 0000:00:1d.2 to 64 > [ 3.384354] uhci_hcd 0000:00:1d.2: UHCI Host Controller > [ 3.384399] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus > number 3 > [ 3.384433] uhci_hcd 0000:00:1d.2: irq 10, io base 0x0000e800 > [ 3.384577] usb usb3: configuration #1 chosen from 1 choice > [ 3.384629] hub 3-0:1.0: USB hub found > [ 3.384640] hub 3-0:1.0: 2 ports detected > [ 3.416319] libata version 3.00 loaded. > [ 3.488204] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 > [ 3.488212] usb usb3: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 3.488218] usb usb3: Product: UHCI Host Controller > [ 3.488223] usb usb3: Manufacturer: Linux 2.6.26-1-686 uhci_hcd > [ 3.488227] usb usb3: SerialNumber: 0000:00:1d.2 > [ 3.488303] ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 5 > (level, low) -> IRQ 5 > [ 3.488320] PCI: Setting latency timer of device 0000:00:1d.3 to 64 > [ 3.488327] uhci_hcd 0000:00:1d.3: UHCI Host Controller > [ 3.488378] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus > number 4 > [ 3.488413] uhci_hcd 0000:00:1d.3: irq 5, io base 0x0000e880 > [ 3.488560] usb usb4: configuration #1 chosen from 1 choice > [ 3.488612] hub 4-0:1.0: USB hub found > [ 3.488625] hub 4-0:1.0: 2 ports detected > [ 3.592215] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 > [ 3.592223] usb usb4: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 3.592229] usb usb4: Product: UHCI Host Controller > [ 3.592234] usb usb4: Manufacturer: Linux 2.6.26-1-686 uhci_hcd > [ 3.592238] usb usb4: SerialNumber: 0000:00:1d.3 > [ 3.593865] ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 3 > (level, low) -> IRQ 3 > [ 3.593890] PCI: Setting latency timer of device 0000:00:1d.7 to 64 > [ 3.593897] ehci_hcd 0000:00:1d.7: EHCI Host Controller > [ 3.593962] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus > number 5 > [ 3.597887] ehci_hcd 0000:00:1d.7: debug port 1 > [ 3.597896] PCI: cache line size of 32 is not supported by device > 0000:00:1d.7 > [ 3.597911] ehci_hcd 0000:00:1d.7: irq 3, io mem 0xf7eb7c00 > [ 3.624100] usb 2-1: new low speed USB device using uhci_hcd and address 2 > [ 3.636034] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver > 10 Dec 2004 > [ 3.636195] usb usb5: configuration #1 chosen from 1 choice > [ 3.636252] hub 5-0:1.0: USB hub found > [ 3.636267] hub 5-0:1.0: 8 ports detected > [ 3.692091] hub 2-0:1.0: unable to enumerate USB device on port 1 > [ 3.740226] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 > [ 3.740234] usb usb5: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 3.740240] usb usb5: Product: EHCI Host Controller > [ 3.740244] usb usb5: Manufacturer: Linux 2.6.26-1-686 ehci_hcd > [ 3.740249] usb usb5: SerialNumber: 0000:00:1d.7 > [ 3.740783] ahci 0000:00:1f.2: version 3.0 > [ 3.740819] ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 7 > (level, low) -> IRQ 7 > [ 3.740844] ACPI: PCI interrupt for device 0000:00:1f.2 disabled > [ 3.740856] ahci: probe of 0000:00:1f.2 failed with error -22 > [ 3.745573] ata_piix 0000:00:1f.2: version 2.12 > [ 3.745593] ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 7 > (level, low) -> IRQ 7 > [ 3.745603] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] > [ 3.745666] PCI: Setting latency timer of device 0000:00:1f.2 to 64 > [ 3.745758] scsi0 : ata_piix > [ 3.745903] scsi1 : ata_piix > [ 3.749073] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 > irq 14 > [ 3.749080] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 > irq 15 > [ 4.092738] ata2.00: ATA-5: ASUS-PHISON OB SSD, TST2.04U, max UDMA/66 > [ 4.092746] ata2.00: 7880544 sectors, multi 0: LBA > [ 4.092784] ata2.01: ATA-5: ASUS-PHISON SSD, TST2.04P, max UDMA/66 > [ 4.092789] ata2.01: 31522176 sectors, multi 0: LBA > [ 4.100659] ata2.00: configured for UDMA/66 > [ 4.108633] ata2.01: configured for UDMA/66 > [ 4.108817] scsi 1:0:0:0: Direct-Access ATA ASUS-PHISON OB S > TST2 PQ: 0 ANSI: 5 > [ 4.109109] scsi 1:0:1:0: Direct-Access ATA ASUS-PHISON SSD > TST2 PQ: 0 ANSI: 5 > [ 4.126696] Uniform Multi-Platform E-IDE driver > [ 4.126708] ide: Assuming 33MHz system bus speed for PIO modes; > override with idebus=xx > [ 4.196148] Driver 'sd' needs updating - please use bus_type methods > [ 4.196314] sd 1:0:0:0: [sda] 7880544 512-byte hardware sectors (4035 MB) > [ 4.196348] sd 1:0:0:0: [sda] Write Protect is off > [ 4.196353] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 4.196409] sd 1:0:0:0: [sda] Write cache: disabled, read cache: > enabled, doesn't support DPO or FUA > [ 4.196525] sd 1:0:0:0: [sda] 7880544 512-byte hardware sectors (4035 MB) > [ 4.196556] sd 1:0:0:0: [sda] Write Protect is off > [ 4.196563] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 4.196618] sd 1:0:0:0: [sda] Write cache: disabled, read cache: > enabled, doesn't support DPO or FUA > [ 4.196625] sda: sda1 > [ 4.198512] sd 1:0:0:0: [sda] Attached SCSI disk > [ 4.198653] sd 1:0:1:0: [sdb] 31522176 512-byte hardware sectors (16139 > MB) > [ 4.198687] sd 1:0:1:0: [sdb] Write Protect is off > [ 4.198693] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > [ 4.198747] sd 1:0:1:0: [sdb] Write cache: disabled, read cache: > enabled, doesn't support DPO or FUA > [ 4.198847] sd 1:0:1:0: [sdb] 31522176 512-byte hardware sectors (16139 > MB) > [ 4.198878] sd 1:0:1:0: [sdb] Write Protect is off > [ 4.198884] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > [ 4.198937] sd 1:0:1:0: [sdb] Write cache: disabled, read cache: > enabled, doesn't support DPO or FUA > [ 4.198945] sdb: sdb1 sdb2 < sdb5 > > [ 4.201758] sd 1:0:1:0: [sdb] Attached SCSI disk > [ 4.392601] PM: Starting manual resume from disk > [ 4.425481] kjournald starting. Commit interval 5 seconds > [ 4.425500] EXT3-fs: mounted filesystem with ordered data mode. > [ 4.744055] usb 5-5: new high speed USB device using ehci_hcd and > address 4 > [ 4.877440] usb 5-5: configuration #1 chosen from 1 choice > [ 4.877868] usb 5-5: New USB device found, idVendor=0951, idProduct=1606 > [ 4.877875] usb 5-5: New USB device strings: Mfr=1, Product=2, > SerialNumber=4 > [ 4.877880] usb 5-5: Product: UB6225 > [ 4.877884] usb 5-5: Manufacturer: ENE > [ 4.877888] usb 5-5: SerialNumber: 146030377350 > [ 5.116092] usb 5-8: new high speed USB device using ehci_hcd and > address 5 > [ 5.128576] udevd version 125 started > [ 5.663525] usb 5-8: configuration #1 chosen from 1 choice > [ 5.665432] usb 5-8: New USB device found, idVendor=05e3, idProduct=0505 > [ 5.665440] usb 5-8: New USB device strings: Mfr=0, Product=1, > SerialNumber=0 > [ 5.665445] usb 5-8: Product: USB 2.0 Camera > [ 5.904061] usb 2-1: new low speed USB device using uhci_hcd and address 3 > [ 6.078974] usb 2-1: configuration #1 chosen from 1 choice > [ 6.092113] usb 2-1: New USB device found, idVendor=093a, idProduct=2510 > [ 6.092121] usb 2-1: New USB device strings: Mfr=1, Product=2, > SerialNumber=0 > [ 6.092127] usb 2-1: Product: USB OPTICAL MOUSE > [ 6.092131] usb 2-1: Manufacturer: PIXART > [ 6.332049] usb 2-2: new full speed USB device using uhci_hcd and > address 4 > [ 6.452049] usb 2-2: device descriptor read/64, error -71 > [ 6.676048] usb 2-2: device descriptor read/64, error -71 > [ 6.892049] usb 2-2: new full speed USB device using uhci_hcd and > address 5 > [ 7.012056] usb 2-2: device descriptor read/64, error -71 > [ 7.184041] Linux agpgart interface v0.103 > [ 7.217692] agpgart: Detected an Intel 915GM Chipset. > [ 7.217903] agpgart: Detected 7932K stolen memory. > [ 7.238885] agpgart: AGP aperture is 256M @ 0xd0000000 > [ 7.238965] usb 2-2: device descriptor read/64, error -71 > [ 7.452044] usb 2-2: new full speed USB device using uhci_hcd and > address 6 > [ 7.860027] usb 2-2: device not accepting address 6, error -71 > [ 7.864253] Atheros(R) L2 Ethernet Driver - version 2.0.5 > [ 7.864259] Copyright (c) 2007 Atheros Corporation. > [ 7.864320] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKB] -> GSI > 11 (level, low) -> IRQ 11 > [ 7.864339] PCI: Setting latency timer of device 0000:03:00.0 to 64 > [ 7.972048] usb 2-2: new full speed USB device using uhci_hcd and > address 7 > [ 8.153587] ath_hal: module license 'Proprietary' taints kernel. > [ 8.176070] AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, > RF5413, RF2133, RF2425, RF2417) > [ 8.179523] eeepc: Eee PC Hotkey Driver > [ 8.179764] eeepc: Hotkey init flags 0x41 > [ 8.181034] eeepc: Get control methods supported: 0x101711 > [ 8.189538] input: Power Button (FF) as /class/input/input1 > [ 8.216368] ACPI: Power Button (FF) [PWRF] > [ 8.216521] input: Lid Switch as /class/input/input2 > [ 8.245309] ACPI: Lid Switch [LID] > [ 8.245427] input: Sleep Button (CM) as /class/input/input3 > [ 8.275834] ACPI: Sleep Button (CM) [SLPB] > [ 8.275940] input: Power Button (CM) as /class/input/input4 > [ 8.303486] ACPI: Power Button (CM) [PWRB] > [ 8.384026] usb 2-2: device not accepting address 7, error -71 > [ 8.384135] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 8.550914] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKC] -> GSI > 10 (level, low) -> IRQ 10 > [ 8.550934] PCI: Setting latency timer of device 0000:01:00.0 to 64 > [ 9.042244] MadWifi: ath_attach: Switching rfkill capability off. > [ 9.735124] ACPI: AC Adapter [AC0] (on-line) > [ 10.756737] ACPI: EC: missing confirmations, switch off interrupt mode. > [ 11.208450] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) > [ 11.208577] iTCO_wdt: Found a ICH6-M TCO device (Version=2, > TCOBASE=0x0860) > [ 11.208620] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) > [ 11.477769] ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> GSI 5 > (level, low) -> IRQ 5 > [ 11.477805] PCI: Setting latency timer of device 0000:00:1b.0 to 64 > [ 11.483562] input: PC Speaker as /class/input/input5 > [ 11.501902] hda_codec: Unknown model for ALC662, trying auto-probe from > BIOS... > [ 11.540394] ACPI: Battery Slot [BAT0] (battery present) > [ 11.541343] input: Video Bus as /class/input/input6 > [ 11.548119] intel_rng: FWH not detected > [ 11.568109] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) > [ 12.410100] Initializing USB Mass Storage driver... > [ 12.410257] scsi2 : SCSI emulation for USB Mass Storage devices > [ 12.410408] usbcore: registered new interface driver usb-storage > [ 12.410415] USB Mass Storage support registered. > [ 12.419980] usb-storage: device found at 4 > [ 12.419987] usb-storage: waiting for device to settle before scanning > [ 12.467956] Linux video capture interface: v2.00 > [ 12.501378] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (05e3:0505) > [ 12.675603] usbcore: registered new interface driver uvcvideo > [ 12.675612] USB Video Class driver (v0.1.0) > [ 12.690664] usbcore: registered new interface driver hiddev > [ 12.706770] input: PIXART USB OPTICAL MOUSE as /class/input/input7 > [ 12.732114] input,hidraw0: USB HID v1.10 Mouse [PIXART USB OPTICAL > MOUSE] on usb-0000:00:1d.1-1 > [ 12.732155] usbcore: registered new interface driver usbhid > [ 12.732161] usbhid: v2.6:USB HID core driver > [ 13.367766] wifi0: Atheros AR2425 chip found (MAC 14.2, PHY SChip 7.0, > Radio 10.2) > [ 13.491684] ath_pci: wifi0: Atheros 5424/2424: mem=0xfbef0000, irq=10 > [ 13.493167] ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKD] -> GSI 7 > (level, low) -> IRQ 7 > [ 14.103195] input: ImPS/2 Logitech Wheel Mouse as /class/input/input8 > [ 14.612235] Adding 706820k swap on /dev/sdb5. Priority:-1 extents:1 > across:706820k > [ 14.741005] EXT3 FS on sdb1, internal journal > [ 15.148504] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > [ 15.156599] pciehp: HPC vendor_id 8086 device_id 2660 ss_vid 0 ss_did 0 > [ 15.156711] Load service driver hpdriver on pcie device > 0000:00:1c.0:pcie02 > [ 15.156733] pciehp: HPC vendor_id 8086 device_id 2662 ss_vid 0 ss_did 0 > [ 16.160089] pciehp: Device 0000:03:00.0 already exists at 3:0, cannot > hot-add > [ 16.160202] pciehp: Cannot add device 0x3:0 > [ 17.164098] Load service driver hpdriver on pcie device > 0000:00:1c.1:pcie02 > [ 17.164136] pciehp: HPC vendor_id 8086 device_id 2664 ss_vid 0 ss_did 0 > [ 17.416293] usb-storage: device scan complete > [ 17.416756] scsi 2:0:0:0: Direct-Access USB2.0 CardReader SD0 > 0100 PQ: 0 ANSI: 0 > [ 17.418374] sd 2:0:0:0: [sdc] Attached SCSI removable disk > [ 18.168064] pciehp: Device 0000:01:00.0 already exists at 1:0, cannot > hot-add > [ 18.168156] pciehp: Cannot add device 0x1:0 > [ 19.172058] Load service driver hpdriver on pcie device > 0000:00:1c.2:pcie02 > [ 19.172108] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 > [ 32.817916] lp: driver loaded but no devices found > [ 32.878596] ppdev: user-space parallel port driver > [ 33.353445] NET: Registered protocol family 10 > [ 33.354326] lo: Disabled Privacy Extensions > [ 33.355270] ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 34.573246] warning: `avahi-daemon' uses 32-bit capabilities (legacy > support in use) > [ 43.156412] Bluetooth: Core ver 2.11 > [ 43.158622] NET: Registered protocol family 31 > [ 43.158632] Bluetooth: HCI device and connection manager initialized > [ 43.158638] Bluetooth: HCI socket layer initialized > [ 43.235432] Bluetooth: L2CAP ver 2.9 > [ 43.235441] Bluetooth: L2CAP socket layer initialized > [ 43.311284] Bluetooth: RFCOMM socket layer initialized > [ 43.311306] Bluetooth: RFCOMM TTY layer initialized > [ 43.311310] Bluetooth: RFCOMM ver 1.8 > [ 49.437113] [drm] Initialized drm 1.1.0 20060810 > [ 50.574435] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 5 > (level, low) -> IRQ 5 > [ 50.574454] PCI: Setting latency timer of device 0000:00:02.0 to 64 > [ 50.574592] [drm] Initialized i915 1.6.0 20060119 on minor 0 > [ 95.536152] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready > [ 111.140013] ath0: no IPv6 routers present > [ 321.816064] usb 2-2: new full speed USB device using uhci_hcd and > address 8 > [ 321.872078] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 323.056069] usb 2-2: new full speed USB device using uhci_hcd and > address 9 > [ 323.198730] usb 2-2: device descriptor read/all, error -71 > [ 323.256090] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 324.296074] usb 2-2: new full speed USB device using uhci_hcd and > address 11 > [ 324.352091] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 325.536036] usb 2-2: new full speed USB device using uhci_hcd and > address 12 > [ 325.686747] usb 2-2: unable to read config index 0 descriptor/all > [ 325.686747] usb 2-2: can't read configurations, error -71 > [ 325.744091] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 326.776039] usb 2-2: new full speed USB device using uhci_hcd and > address 14 > [ 326.832092] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 328.016070] usb 2-2: new full speed USB device using uhci_hcd and > address 15 > [ 328.072161] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 329.256077] usb 2-2: new full speed USB device using uhci_hcd and > address 16 > [ 329.312097] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 330.496075] usb 2-2: new full speed USB device using uhci_hcd and > address 17 > [ 330.552108] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 331.736069] usb 2-2: new full speed USB device using uhci_hcd and > address 18 > [ 331.878747] usb 2-2: device descriptor read/all, error -71 > [ 331.936095] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 332.976078] usb 2-2: new full speed USB device using uhci_hcd and > address 20 > [ 333.118668] usb 2-2: device descriptor read/all, error -71 > [ 333.176108] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 334.216075] usb 2-2: new full speed USB device using uhci_hcd and > address 22 > [ 334.272108] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 335.456137] usb 2-2: new full speed USB device using uhci_hcd and > address 23 > [ 335.512118] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 336.696071] usb 2-2: new full speed USB device using uhci_hcd and > address 24 > [ 336.838739] usb 2-2: device descriptor read/all, error -71 > [ 336.896067] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 337.936069] usb 2-2: new full speed USB device using uhci_hcd and > address 26 > [ 337.992105] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 339.176075] usb 2-2: new full speed USB device using uhci_hcd and > address 27 > [ 339.236097] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 340.416067] usb 2-2: new full speed USB device using uhci_hcd and > address 28 > [ 340.476107] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 341.656078] usb 2-2: new full speed USB device using uhci_hcd and > address 29 > [ 341.827652] usb 2-2: configuration #1 chosen from 1 choice > [ 341.833292] usb 2-2: can't set config #1, error -71 > [ 341.833436] usb 2-2: New USB device found, idVendor=04d8, idProduct=000a > [ 341.833443] usb 2-2: New USB device strings: Mfr=1, Product=2, > SerialNumber=3 > [ 341.833468] usb 2-2: USB disconnect, address 29 > [ 342.896078] usb 2-2: new full speed USB device using uhci_hcd and > address 30 > [ 342.952095] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 344.136074] usb 2-2: new full speed USB device using uhci_hcd and > address 31 > [ 344.192112] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 345.376075] usb 2-2: new full speed USB device using uhci_hcd and > address 32 > [ 345.436065] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 346.616073] usb 2-2: new full speed USB device using uhci_hcd and > address 33 > [ 346.758870] usb 2-2: device descriptor read/all, error -71 > [ 346.816090] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 347.856079] usb 2-2: new full speed USB device using uhci_hcd and > address 35 > [ 347.998741] usb 2-2: device descriptor read/all, error -71 > [ 348.056093] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 349.096073] usb 2-2: new full speed USB device using uhci_hcd and > address 37 > [ 349.246504] usb 2-2: unable to read config index 0 descriptor/all > [ 349.246504] usb 2-2: can't read configurations, error -71 > [ 349.304144] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 350.336071] usb 2-2: new full speed USB device using uhci_hcd and > address 39 > [ 350.486581] usb 2-2: unable to read config index 0 descriptor/all > [ 350.486581] usb 2-2: can't read configurations, error -71 > [ 350.544097] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 351.576075] usb 2-2: new full speed USB device using uhci_hcd and > address 41 > [ 351.729542] usb 2-2: unable to read config index 0 descriptor/all > [ 351.729542] usb 2-2: can't read configurations, error -71 > [ 351.784099] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 352.816067] usb 2-2: new full speed USB device using uhci_hcd and > address 43 > [ 352.872105] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 354.056173] usb 2-2: new full speed USB device using uhci_hcd and > address 44 > [ 354.198756] usb 2-2: device descriptor read/all, error -71 > [ 354.256102] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 355.296075] usb 2-2: new full speed USB device using uhci_hcd and > address 46 > [ 355.446516] usb 2-2: unable to read config index 0 descriptor/all > [ 355.446516] usb 2-2: can't read configurations, error -71 > [ 355.504102] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 356.536041] usb 2-2: new full speed USB device using uhci_hcd and > address 48 > [ 356.686702] usb 2-2: unable to read config index 0 descriptor/all > [ 356.686702] usb 2-2: can't read configurations, error -71 > [ 356.744059] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 357.776045] usb 2-2: new full speed USB device using uhci_hcd and > address 50 > [ 357.926582] usb 2-2: unable to read config index 0 descriptor/all > [ 357.926582] usb 2-2: can't read configurations, error -71 > [ 357.984071] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 359.016069] usb 2-2: new full speed USB device using uhci_hcd and > address 52 > [ 359.072171] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 360.256077] usb 2-2: new full speed USB device using uhci_hcd and > address 53 > [ 360.316100] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 361.496046] usb 2-2: new full speed USB device using uhci_hcd and > address 54 > [ 361.646872] usb 2-2: unable to read config index 0 descriptor/all > [ 361.646883] usb 2-2: can't read configurations, error -71 > [ 361.704071] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 362.736071] usb 2-2: new full speed USB device using uhci_hcd and > address 56 > [ 362.878746] usb 2-2: device descriptor read/all, error -71 > [ 362.936069] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 363.976081] usb 2-2: new full speed USB device using uhci_hcd and > address 58 > [ 364.032099] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 365.216069] usb 2-2: new full speed USB device using uhci_hcd and > address 59 > [ 365.361850] usb 2-2: device descriptor read/all, error -71 > [ 365.416095] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 366.456076] usb 2-2: new full speed USB device using uhci_hcd and > address 61 > [ 366.512099] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 367.696078] usb 2-2: new full speed USB device using uhci_hcd and > address 62 > [ 367.838690] usb 2-2: device descriptor read/all, error -71 > [ 367.896101] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 368.936044] usb 2-2: new full speed USB device using uhci_hcd and > address 64 > [ 368.992106] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 370.176080] usb 2-2: new full speed USB device using uhci_hcd and > address 65 > [ 370.232103] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 371.416073] usb 2-2: new full speed USB device using uhci_hcd and > address 66 > [ 371.472106] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 372.656082] usb 2-2: new full speed USB device using uhci_hcd and > address 67 > [ 372.712103] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 373.896080] usb 2-2: new full speed USB device using uhci_hcd and > address 68 > [ 374.045624] usb 2-2: unable to read config index 0 descriptor/start: -71 > [ 374.045624] usb 2-2: chopping to 0 config(s) > [ 374.053868] usb 2-2: string descriptor 0 read error: -71 > [ 374.061828] usb 2-2: string descriptor 0 read error: -71 > [ 374.069525] usb 2-2: string descriptor 0 read error: -71 > [ 374.069525] usb 2-2: no configuration chosen from 0 choices > [ 374.069525] usb 2-2: New USB device found, idVendor=04d8, idProduct=000a > [ 374.069525] usb 2-2: New USB device strings: Mfr=1, Product=2, > SerialNumber=3 > [ 374.069525] usb 2-2: USB disconnect, address 68 > [ 375.136075] usb 2-2: new full speed USB device using uhci_hcd and > address 69 > [ 375.192110] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 376.376083] usb 2-2: new full speed USB device using uhci_hcd and > address 70 > [ 376.432100] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 377.616075] usb 2-2: new full speed USB device using uhci_hcd and > address 71 > [ 377.767653] usb 2-2: unable to read config index 0 descriptor/all > [ 377.767653] usb 2-2: can't read configurations, error -71 > [ 377.824096] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 378.856084] usb 2-2: new full speed USB device using uhci_hcd and > address 73 > [ 378.912074] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 380.096078] usb 2-2: new full speed USB device using uhci_hcd and > address 74 > [ 380.246755] usb 2-2: unable to read config index 0 descriptor/all > [ 380.246755] usb 2-2: can't read configurations, error -71 > [ 380.304106] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 381.336075] usb 2-2: new full speed USB device using uhci_hcd and > address 76 > [ 381.392112] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 382.576042] usb 2-2: new full speed USB device using uhci_hcd and > address 77 > [ 382.718749] usb 2-2: device descriptor read/all, error -71 > [ 382.776103] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 383.816074] usb 2-2: new full speed USB device using uhci_hcd and > address 79 > [ 383.966777] usb 2-2: unable to read config index 0 descriptor/all > [ 383.966777] usb 2-2: can't read configurations, error -71 > [ 384.024099] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 385.056078] usb 2-2: new full speed USB device using uhci_hcd and > address 81 > [ 385.112104] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 386.296083] usb 2-2: new full speed USB device using uhci_hcd and > address 82 > [ 386.352162] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 387.536079] usb 2-2: new full speed USB device using uhci_hcd and > address 83 > [ 387.592105] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 388.776083] usb 2-2: new full speed USB device using uhci_hcd and > address 84 > [ 388.926509] usb 2-2: unable to read config index 0 descriptor/all > [ 388.926509] usb 2-2: can't read configurations, error -71 > [ 388.984109] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 390.016074] usb 2-2: new full speed USB device using uhci_hcd and > address 86 > [ 390.158884] usb 2-2: device descriptor read/all, error -71 > [ 390.216060] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 391.256077] usb 2-2: new full speed USB device using uhci_hcd and > address 88 > [ 391.406576] usb 2-2: unable to read config index 0 descriptor/all > [ 391.406576] usb 2-2: can't read configurations, error -71 > [ 391.464106] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 392.496156] usb 2-2: new full speed USB device using uhci_hcd and > address 90 > [ 392.552101] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 393.736084] usb 2-2: new full speed USB device using uhci_hcd and > address 91 > [ 393.792110] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 394.976043] usb 2-2: new full speed USB device using uhci_hcd and > address 92 > [ 395.121683] usb 2-2: device descriptor read/all, error -71 > [ 395.176103] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 396.216038] usb 2-2: new full speed USB device using uhci_hcd and > address 94 > [ 396.366761] usb 2-2: unable to read config index 0 descriptor/all > [ 396.366762] usb 2-2: can't read configurations, error -71 > [ 396.424065] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 397.456073] usb 2-2: new full speed USB device using uhci_hcd and > address 96 > [ 397.606587] usb 2-2: unable to read config index 0 descriptor/all > [ 397.606587] usb 2-2: can't read configurations, error -71 > [ 397.664109] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 398.696080] usb 2-2: new full speed USB device using uhci_hcd and > address 98 > [ 398.838747] usb 2-2: device descriptor read/all, error -71 > [ 398.896068] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 399.936072] usb 2-2: new full speed USB device using uhci_hcd and > address 100 > [ 400.085736] usb 2-2: unable to read config index 0 descriptor/start: -71 > [ 400.085736] usb 2-2: chopping to 0 config(s) > [ 400.093874] usb 2-2: string descriptor 0 read error: -71 > [ 400.101757] usb 2-2: string descriptor 0 read error: -71 > [ 400.109490] usb 2-2: string descriptor 0 read error: -71 > [ 400.109490] usb 2-2: no configuration chosen from 0 choices > [ 400.109490] usb 2-2: New USB device found, idVendor=04d8, idProduct=000a > [ 400.109490] usb 2-2: New USB device strings: Mfr=1, Product=2, > SerialNumber=3 > [ 400.109490] usb 2-2: USB disconnect, address 100 > [ 401.176045] usb 2-2: new full speed USB device using uhci_hcd and > address 101 > [ 401.232064] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 402.416082] usb 2-2: new full speed USB device using uhci_hcd and > address 102 > [ 402.472111] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 403.656082] usb 2-2: new full speed USB device using uhci_hcd and > address 103 > [ 403.712103] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 404.896044] usb 2-2: new full speed USB device using uhci_hcd and > address 104 > [ 404.952098] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 406.136072] usb 2-2: new full speed USB device using uhci_hcd and > address 105 > [ 406.192107] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 407.376078] usb 2-2: new full speed USB device using uhci_hcd and > address 106 > [ 407.432115] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 408.616099] usb 2-2: new full speed USB device using uhci_hcd and > address 107 > [ 408.766762] usb 2-2: unable to read config index 0 descriptor/all > [ 408.766762] usb 2-2: can't read configurations, error -71 > [ 408.824118] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 409.856084] usb 2-2: new full speed USB device using uhci_hcd and > address 109 > [ 409.912132] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 411.096048] usb 2-2: new full speed USB device using uhci_hcd and > address 110 > [ 411.245982] usb 2-2: unable to read config index 0 descriptor/all > [ 411.245982] usb 2-2: can't read configurations, error -71 > [ 411.304077] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 412.336053] usb 2-2: new full speed USB device using uhci_hcd and > address 112 > [ 412.392081] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 413.576055] usb 2-2: new full speed USB device using uhci_hcd and > address 113 > [ 413.632078] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 414.816046] usb 2-2: new full speed USB device using uhci_hcd and > address 114 > [ 414.872082] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 416.056052] usb 2-2: new full speed USB device using uhci_hcd and > address 115 > [ 416.207055] usb 2-2: unable to read config index 0 descriptor/all > [ 416.207055] usb 2-2: can't read configurations, error -71 > [ 416.264080] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 417.296046] usb 2-2: new full speed USB device using uhci_hcd and > address 117 > [ 417.446150] usb 2-2: unable to read config index 0 descriptor/all > [ 417.446150] usb 2-2: can't read configurations, error -71 > [ 417.504136] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 418.536048] usb 2-2: new full speed USB device using uhci_hcd and > address 119 > [ 418.686768] usb 2-2: unable to read config index 0 descriptor/all > [ 418.686768] usb 2-2: can't read configurations, error -71 > [ 418.744077] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 419.776055] usb 2-2: new full speed USB device using uhci_hcd and > address 121 > [ 419.832073] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 421.016049] usb 2-2: new full speed USB device using uhci_hcd and > address 122 > [ 421.072088] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 422.256049] usb 2-2: new full speed USB device using uhci_hcd and > address 123 > [ 422.398770] usb 2-2: device descriptor read/all, error -71 > [ 422.456076] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 423.496051] usb 2-2: new full speed USB device using uhci_hcd and > address 125 > [ 423.646900] usb 2-2: unable to read config index 0 descriptor/all > [ 423.646914] usb 2-2: can't read configurations, error -71 > [ 423.704075] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 424.736046] usb 2-2: new full speed USB device using uhci_hcd and > address 127 > [ 424.886764] usb 2-2: unable to read config index 0 descriptor/all > [ 424.886778] usb 2-2: can't read configurations, error -71 > [ 424.944071] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 425.976048] usb 2-2: new full speed USB device using uhci_hcd and > address 4 > [ 426.121685] usb 2-2: device descriptor read/all, error -71 > [ 426.176082] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 427.216049] usb 2-2: new full speed USB device using uhci_hcd and > address 6 > [ 427.272083] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 428.456049] usb 2-2: new full speed USB device using uhci_hcd and > address 7 > [ 428.512072] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 429.696049] usb 2-2: new full speed USB device using uhci_hcd and > address 8 > [ 429.752079] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 430.936052] usb 2-2: new full speed USB device using uhci_hcd and > address 9 > [ 431.086733] usb 2-2: unable to read config index 0 descriptor/all > [ 431.086733] usb 2-2: can't read configurations, error -71 > [ 431.144075] hub 2-0:1.0: unable to enumerate USB device on port 2 > [ 432.176055] usb 2-2: new full speed USB device using uhci_hcd and > address 11 > [ 432.318826] usb 2-2: device descriptor read/all, error -71 > [ 432.376080] hub 2-0:1.0: unable to enumerate USB device on port 2 > > lsmod -v: > Module Size Used by > wlan_ccmp 6496 2 > i915 25280 2 > drm 65256 3 i915 > rfcomm 28272 0 > l2cap 17248 5 rfcomm > bluetooth 44900 4 rfcomm,l2cap > ipv6 235300 14 > ppdev 6468 0 > parport_pc 22500 0 > lp 8164 0 > parport 30988 3 ppdev,parport_pc,lp > cpufreq_powersave 1856 0 > cpufreq_stats 3776 0 > cpufreq_userspace 3172 0 > cpufreq_ondemand 6476 0 > cpufreq_conservative 5960 0 > freq_table 4224 2 cpufreq_stats,cpufreq_ondemand > cdc_acm 12224 0 > pciehp 28540 0 > pci_hotplug 23460 1 pciehp > wlan_scan_sta 11296 1 > usbhid 35904 0 > hid 33184 1 usbhid > ff_memless 4392 1 usbhid > uvcvideo 45704 0 > compat_ioctl32 1312 1 uvcvideo > videodev 27520 1 uvcvideo > v4l1_compat 12260 2 uvcvideo,videodev > usb_storage 75936 0 > serio_raw 4740 0 > psmouse 32336 0 > rng_core 3940 0 > pcspkr 2432 0 > i2c_i801 7920 0 > snd_hda_intel 324248 1 > i2c_core 19828 1 i2c_i801 > snd_pcm_oss 32800 0 > snd_pcm 62596 2 snd_hda_intel,snd_pcm_oss > iTCO_wdt 9508 0 > snd_mixer_oss 12320 1 snd_pcm_oss > video 16432 0 > output 2912 1 video > battery 10180 0 > snd_seq_dummy 2660 0 > ac 4196 0 > ath_rate_sample 11104 1 > ath_pci 202712 0 > eeepc_laptop 7440 0 > button 6096 0 > wlan 194000 5 > wlan_ccmp,wlan_scan_sta,ath_rate_sample,ath_pci > ath_hal 300768 3 ath_rate_sample,ath_pci > atl2 22744 0 > snd_seq_oss 24992 0 > snd_seq_midi_event 6432 1 snd_seq_oss > snd_seq 41456 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event > snd_timer 17800 2 snd_pcm,snd_seq > snd_seq_device 6380 3 snd_seq_dummy,snd_seq_oss,snd_seq > snd 45604 10 > snd_hda_intel,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_seq_oss,snd_seq,snd_timer,snd_seq_device > intel_agp 22332 1 > agpgart 28776 3 drm,intel_agp > soundcore 6368 1 snd > snd_page_alloc 7816 2 snd_hda_intel,snd_pcm > evdev 8000 6 > ext3 105512 1 > jbd 39444 1 ext3 > mbcache 7108 1 ext3 > sd_mod 22200 3 > ide_pci_generic 3908 0 [permanent] > ide_core 96168 1 ide_pci_generic > ata_generic 4676 0 > ata_piix 14180 2 > ahci 23176 0 > libata 140384 3 ata_generic,ata_piix,ahci > scsi_mod 129356 3 usb_storage,sd_mod,libata > dock 8304 1 libata > ehci_hcd 28428 0 > uhci_hcd 18672 0 > usbcore 118160 7 > cdc_acm,usbhid,uvcvideo,usb_storage,ehci_hcd,uhci_hcd > thermal 15228 0 > processor 32576 2 thermal > fan 4164 0 > thermal_sys 10856 4 video,thermal,processor,fan > > lspci: > 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express > Processor to DRAM Controller (rev 04) > Subsystem: ASUSTeK Computer Inc. Device 82d9 > Flags: bus master, fast devsel, latency 0 > Capabilities: [e0] Vendor Specific Information <?> > Kernel driver in use: agpgart-intel > Kernel modules: intel-agp > > 00:02.0 VGA compatible controller: Intel Corporation Mobile > 915GM/GMS/910GML Express Graphics Controller (rev 04) (prog-if 00 [VGA > controller]) > Subsystem: ASUSTeK Computer Inc. Device 82d9 > Flags: bus master, fast devsel, latency 0, IRQ 16 > Memory at f7f00000 (32-bit, non-prefetchable) [size=512K] > I/O ports at ec00 [size=8] > Memory at d0000000 (32-bit, prefetchable) [size=256M] > Memory at f7ec0000 (32-bit, non-prefetchable) [size=256K] > Capabilities: [d0] Power Management version 2 > Kernel modules: intelfb > > 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML > Express Graphics Controller (rev 04) > Subsystem: ASUSTeK Computer Inc. Device 82d9 > Flags: bus master, fast devsel, latency 0 > Memory at f7f80000 (32-bit, non-prefetchable) [size=512K] > Capabilities: [d0] Power Management version 2 > > 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) High Definition Audio Controller (rev 04) > Subsystem: ASUSTeK Computer Inc. Device 8337 > Flags: bus master, fast devsel, latency 0, IRQ 16 > Memory at f7eb8000 (64-bit, non-prefetchable) [size=16K] > Capabilities: [50] Power Management version 2 > Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 > Enable- > Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 > Capabilities: [100] Virtual Channel <?> > Capabilities: [130] Root Complex Link <?> > Kernel driver in use: HDA Intel > Kernel modules: snd-hda-intel > > 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) > PCI Express Port 1 (rev 04) (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > Capabilities: [40] Express Root Port (Slot+), MSI 00 > Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 > Enable+ > Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8 > Capabilities: [a0] Power Management version 2 > Capabilities: [100] Virtual Channel <?> > Capabilities: [180] Root Complex Link <?> > Kernel driver in use: pcieport-driver > Kernel modules: shpchp > > 00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) > PCI Express Port 2 (rev 04) (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > Memory behind bridge: fbf00000-fbffffff > Capabilities: [40] Express Root Port (Slot+), MSI 00 > Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 > Enable+ > Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8 > Capabilities: [a0] Power Management version 2 > Capabilities: [100] Virtual Channel <?> > Capabilities: [180] Root Complex Link <?> > Kernel driver in use: pcieport-driver > Kernel modules: shpchp > > 00:1c.2 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) > PCI Express Port 3 (rev 04) (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=01, subordinate=02, sec-latency=0 > Memory behind bridge: f8000000-fbefffff > Prefetchable memory behind bridge: 00000000f0000000-00000000f6ffffff > Capabilities: [40] Express Root Port (Slot+), MSI 00 > Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 > Enable+ > Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8 > Capabilities: [a0] Power Management version 2 > Capabilities: [100] Virtual Channel <?> > Capabilities: [180] Root Complex Link <?> > Kernel driver in use: pcieport-driver > Kernel modules: shpchp > > 00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) USB UHCI #1 (rev 04) (prog-if 00 [UHCI]) > Subsystem: ASUSTeK Computer Inc. Device 82d8 > Flags: bus master, medium devsel, latency 0, IRQ 23 > I/O ports at e400 [size=32] > Kernel driver in use: uhci_hcd > Kernel modules: uhci-hcd > > 00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) USB UHCI #2 (rev 04) (prog-if 00 [UHCI]) > Subsystem: ASUSTeK Computer Inc. Device 82d8 > Flags: bus master, medium devsel, latency 0, IRQ 19 > I/O ports at e480 [size=32] > Kernel driver in use: uhci_hcd > Kernel modules: uhci-hcd > > 00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) USB UHCI #3 (rev 04) (prog-if 00 [UHCI]) > Subsystem: ASUSTeK Computer Inc. Device 82d8 > Flags: bus master, medium devsel, latency 0, IRQ 18 > I/O ports at e800 [size=32] > Kernel driver in use: uhci_hcd > Kernel modules: uhci-hcd > > 00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) USB UHCI #4 (rev 04) (prog-if 00 [UHCI]) > Subsystem: ASUSTeK Computer Inc. Device 82d8 > Flags: bus master, medium devsel, latency 0, IRQ 16 > I/O ports at e880 [size=32] > Kernel driver in use: uhci_hcd > Kernel modules: uhci-hcd > > 00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) USB2 EHCI Controller (rev 04) (prog-if 20 [EHCI]) > Subsystem: ASUSTeK Computer Inc. Device 82d8 > Flags: bus master, medium devsel, latency 0, IRQ 23 > Memory at f7eb7c00 (32-bit, non-prefetchable) [size=1K] > Capabilities: [50] Power Management version 2 > Capabilities: [58] Debug port: BAR=1 offset=00a0 > Kernel driver in use: ehci_hcd > Kernel modules: ehci-hcd > > 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4) > (prog-if 01 [Subtractive decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=05, subordinate=05, sec-latency=32 > Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device 82d8 > > 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface > Bridge (rev 04) > Subsystem: ASUSTeK Computer Inc. Device 82d8 > Flags: bus master, medium devsel, latency 0 > Kernel modules: intel-rng, iTCO_wdt > > 00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller > (rev 04) (prog-if 80 [Master]) > Subsystem: ASUSTeK Computer Inc. Device 82d8 > Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19 > I/O ports at 01f0 [size=8] > I/O ports at 03f4 [size=1] > I/O ports at 0170 [size=8] > I/O ports at 0374 [size=1] > I/O ports at ffa0 [size=16] > Capabilities: [70] Power Management version 2 > Kernel driver in use: ata_piix > Kernel modules: ahci, ata_piix > > 00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus > Controller (rev 04) > Subsystem: ASUSTeK Computer Inc. Device 82d8 > Flags: medium devsel, IRQ 19 > I/O ports at 0400 [size=32] > Kernel driver in use: i801_smbus > Kernel modules: i2c-i801 > > 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg > Wireless PCI Express Adapter (rev 01) > Subsystem: Device 1a3b:1026 > Flags: bus master, fast devsel, latency 0, IRQ 18 > Memory at fbef0000 (64-bit, non-prefetchable) [size=64K] > Capabilities: [40] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 > Enable- > Capabilities: [60] Express Legacy Endpoint, MSI 00 > Capabilities: [90] MSI-X: Enable- Mask- TabSize=1 > Capabilities: [100] Advanced Error Reporting <?> > Capabilities: [140] Virtual Channel <?> > Kernel driver in use: ath_pci > Kernel modules: ath_pci, ath5k > > 03:00.0 Ethernet controller: Attansic Technology Corp. L2 100 Mbit > Ethernet Adapter (rev a0) > Subsystem: ASUSTeK Computer Inc. Device 8233 > Flags: bus master, fast devsel, latency 0, IRQ 220 > Memory at fbfc0000 (64-bit, non-prefetchable) [size=256K] > Expansion ROM at fbfa0000 [disabled] [size=128K] > Capabilities: [40] Power Management version 2 > Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 > Enable+ > Capabilities: [58] Express Endpoint, MSI 00 > Capabilities: [6c] Vital Product Data <?> > Capabilities: [100] Advanced Error Reporting <?> > Kernel driver in use: atl2 > Kernel modules: atl2 > > > Any suggestion is very welcome. > Thanks. > Wim > > > > -- > To unsubscribe from this list: send the line "unsubscribe linux-usb" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
