On Wed, Jun 01, 2016 at 10:02:21AM +0200, Krzysztof Kozlowski wrote:
> On Odroid U3 (Exynos4412-based) board if USB was initialized by
> bootloader (in U-Boot "usb start" before tftpboot), the HUB (usb3503)
> and LAN (smsc95xx) after after successful probing were not visible in the
> system ("lsusb").
>
> In such case the devices had to be fully reset before configuring.
> Reset by GPIO (called RESET_N pin) and by RESET field in STCD register
> in usb3503 HUB are not sufficient. Instead full reset has to be done by
> disabling and enabling regulator.
>
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
> ---
> arch/arm/boot/dts/exynos4412-odroidu3.dts | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts
> index 31cdc036fda4..23e30e4609df 100644
> --- a/arch/arm/boot/dts/exynos4412-odroidu3.dts
> +++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts
> @@ -99,11 +99,15 @@
> clock-names = "refclk";
> clocks = <&pmu_system_controller 0>;
> refclk-frequency = <24000000>;
> +
> + power-sequence;
> + ext-supply = <&buck8_reg>;
> };
>
> &ehci {
> port@1 {
> status = "okay";
> + usb-pwrseq = <&usb3503>;
> };
> port@2 {
> status = "okay";
> --
> 1.9.1
>
The hub is under the port1, you may need to describe it
under the port@1, see below:
Documentation/devicetree/bindings/usb/usb-device.txt
If I get Rob's comments correctly, you may need to consider
below MMC and USB device tree description together, it seems
hard for USB to use pwrseq driver, sorry for confusing you.
If rob can accept below USB device description, we have to
do it under USB. In future, if there is some suitable framework,
we can move it.
1. MMC device:
usdhc3_pwrseq: usdhc3_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>, /* WL_REG_ON */
<&gpio4 7 GPIO_ACTIVE_LOW>, /* WL_HOSTWAKE */
<&gpio3 25 GPIO_ACTIVE_LOW>, /* BT_REG_ON */
<&gpio3 27 GPIO_ACTIVE_LOW>, /* BT_HOSTWAKE */
<&gpio4 4 GPIO_ACTIVE_LOW>, /* BT_WAKE */
<&gpio4 6 GPIO_ACTIVE_LOW>; /* BT_RST_N */
};
&usdhc3 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc3>;
pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
bus-width = <4>;
non-removable;
keep-power-in-suspend;
wakeup-source;
mmc-pwrseq = <&usdhc3_pwrseq>;
status = "okay";
};
2. USB device
&usbotg1 {
vbus-supply = <®_usb_otg1_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb_otg1_id>;
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
hub: genesys@1 {
compatible = "usb5e3,608";
reg = <1>;
reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */
reset-duration-us = <10>;
clocks = <&clks IMX6SX_CLK_CKO>;
};
};
};
--
Best Regards,
Peter Chen
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
