Re: [linux-sunxi] Re: [PATCH v3 2/2] phy-sun4i-usb: Add support for the host usb-phys found on the H3 SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On 25-11-15 23:11, Rob Herring wrote:
On Wed, Nov 25, 2015 at 05:50:02PM +0100, Hans de Goede wrote:
From: Reinder de Haan <patchesrdh@xxxxxxxxx>

Note this commit only adds support for phys 1-3, phy 0, the otg phy, is
not yet (fully) supported after this commit.

Shouldn't the OTG phy have a different compatible string?

All 4 phy's are part of one hardware block and they
share some registers, so for sunxi we've always had
one devicetree node describing all usb-phys which
then instantiates multiple phys. E.G. for the A10 we
use:

                usbphy: phy@01c13400 {
                        #phy-cells = <1>;
                        compatible = "allwinner,sun4i-a10-usb-phy";
			...
		};

                usb_otg: usb@01c13000 {
			...
			phys = <&usbphy 0>;
			...
		};

                ehci0: usb@01c14000 {
			...
			phys = <&usbphy 1>;
			...
		};

		...

On the H3 some aspects of the phys have changed, but they still part
of a single hardware block and sharing registers, so we are modelling
them the same way in devicetree and thus they share a single compatible.

Regards,

Hans



		


Signed-off-by: Reinder de Haan <patchesrdh@xxxxxxxxx>
Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
---
Changes in v2:
-Change break; after dev_err() to return, as intended, fixing a compiler
  warning (the dev_err case should never be reached)
Changes in v3:
-Use of_match_node to get model specific config data
---
  .../devicetree/bindings/phy/sun4i-usb-phy.txt      |  1 +
  drivers/phy/phy-sun4i-usb.c                        | 46 +++++++++++++++++-----
  2 files changed, 38 insertions(+), 9 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
index 0cebf74..95736d7 100644
--- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
+++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
@@ -9,6 +9,7 @@ Required properties:
    * allwinner,sun7i-a20-usb-phy
    * allwinner,sun8i-a23-usb-phy
    * allwinner,sun8i-a33-usb-phy
+  * allwinner,sun8i-h3-usb-phy
  - reg : a list of offset + length pairs
  - reg-names :
    * "phy_ctrl"
diff --git a/drivers/phy/phy-sun4i-usb.c b/drivers/phy/phy-sun4i-usb.c
index 1d8f85d..2aed482 100644
--- a/drivers/phy/phy-sun4i-usb.c
+++ b/drivers/phy/phy-sun4i-usb.c
@@ -46,6 +46,9 @@
  #define REG_PHYBIST			0x08
  #define REG_PHYTUNE			0x0c
  #define REG_PHYCTL_A33			0x10
+#define REG_PHY_UNK_H3			0x20
+
+#define REG_PMU_UNK_H3			0x10

  #define PHYCTL_DATA			BIT(7)

@@ -79,7 +82,7 @@
  #define PHY_DISCON_TH_SEL		0x2a
  #define PHY_SQUELCH_DETECT		0x3c

-#define MAX_PHYS			3
+#define MAX_PHYS			4

  /*
   * Note do not raise the debounce time, we must report Vusb high within 100ms
@@ -91,6 +94,7 @@
  enum sun4i_usb_phy_type {
  	sun4i_a10_phy,
  	sun8i_a33_phy,
+	sun8i_h3_phy,
  };

  struct sun4i_usb_phy_cfg {
@@ -101,6 +105,7 @@ struct sun4i_usb_phy_cfg {
  };

  struct sun4i_usb_phy_data {
+	struct device *dev;
  	void __iomem *base;
  	const struct sun4i_usb_phy_cfg *cfg;
  	struct mutex mutex;
@@ -183,6 +188,9 @@ static void sun4i_usb_phy_write(struct sun4i_usb_phy *phy, u32 addr, u32 data,
  		/* A33 needs us to set phyctl to 0 explicitly */
  		writel(0, phyctl);
  		break;
+	case sun8i_h3_phy:
+		dev_err(phy_data->dev, "H3 usb_phy_write is not supported\n");
+		return;
  	}

  	for (i = 0; i < len; i++) {
@@ -243,6 +251,7 @@ static int sun4i_usb_phy_init(struct phy *_phy)
  	struct sun4i_usb_phy *phy = phy_get_drvdata(_phy);
  	struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy);
  	int ret;
+	u32 val;

  	ret = clk_prepare_enable(phy->clk);
  	if (ret)
@@ -254,16 +263,26 @@ static int sun4i_usb_phy_init(struct phy *_phy)
  		return ret;
  	}

-	/* Enable USB 45 Ohm resistor calibration */
-	if (phy->index == 0)
-		sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
+	if (data->cfg->type == sun8i_h3_phy) {
+		if (phy->index == 0) {
+			val = readl(data->base + REG_PHY_UNK_H3);
+			writel(val & ~1, data->base + REG_PHY_UNK_H3);
+		}

-	/* Adjust PHY's magnitude and rate */
-	sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5);
+		val = readl(phy->pmu + REG_PMU_UNK_H3);
+		writel(val & ~2, phy->pmu + REG_PMU_UNK_H3);
+	} else {
+		/* Enable USB 45 Ohm resistor calibration */
+		if (phy->index == 0)
+			sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);

-	/* Disconnect threshold adjustment */
-	sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
-			    data->cfg->disc_thresh, 2);
+		/* Adjust PHY's magnitude and rate */
+		sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5);
+
+		/* Disconnect threshold adjustment */
+		sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
+				    data->cfg->disc_thresh, 2);
+	}

  	sun4i_usb_phy_passby(phy, 1);

@@ -555,6 +574,13 @@ static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
  	.dedicated_clocks = true,
  };

+static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
+	.num_phys = 4,
+	.disc_thresh = 3,
+	.type = sun8i_h3_phy,
+	.dedicated_clocks = true,
+};
+
  static const struct of_device_id sun4i_usb_phy_of_match[] = {
  	{ .compatible = "allwinner,sun4i-a10-usb-phy", .data = &sun4i_a10_cfg },
  	{ .compatible = "allwinner,sun5i-a13-usb-phy", .data = &sun5i_a13_cfg },
@@ -562,6 +588,7 @@ static const struct of_device_id sun4i_usb_phy_of_match[] = {
  	{ .compatible = "allwinner,sun7i-a20-usb-phy", .data = &sun7i_a20_cfg },
  	{ .compatible = "allwinner,sun8i-a23-usb-phy", .data = &sun8i_a23_cfg },
  	{ .compatible = "allwinner,sun8i-a33-usb-phy", .data = &sun8i_a33_cfg },
+	{ .compatible = "allwinner,sun8i-h3-usb-phy", .data = &sun8i_h3_cfg },
  	{ },
  };
  MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match);
@@ -595,6 +622,7 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
  	mutex_init(&data->mutex);
  	INIT_DELAYED_WORK(&data->detect, sun4i_usb_phy0_id_vbus_det_scan);
  	dev_set_drvdata(dev, data);
+	data->dev = dev;
  	data->cfg = match->data;

  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy_ctrl");
--
2.5.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux