Felipe, On Thu, May 14, 2015 at 2:04 PM, Felipe Balbi <balbi@xxxxxx> wrote: > On Thu, May 14, 2015 at 12:49:07PM -0500, Felipe Balbi wrote: >> On Thu, May 14, 2015 at 12:40:31PM -0500, Felipe Balbi wrote: >> > On Thu, May 14, 2015 at 12:07:00PM -0500, Felipe Balbi wrote: >> > > Hi, >> > > >> > > On Wed, Feb 25, 2015 at 01:11:22PM +0100, Yegor Yefremov wrote: >> > > > On 25.02.2015 12:11, Maxime Ripard wrote: >> > > > > On Tue, Feb 24, 2015 at 11:33:57AM -0600, Felipe Balbi wrote: >> > > > >> Hi, >> > > > >> >> > > > >> On Tue, Feb 24, 2015 at 05:50:50PM +0100, Maxime Ripard wrote: >> > > > >>> Hi Felipe, >> > > > >>> >> > > > >>> On Tue, Feb 24, 2015 at 08:54:01AM -0600, Felipe Balbi wrote: >> > > > >>>> Hi, >> > > > >>>> >> > > > >>>> On Tue, Feb 24, 2015 at 11:39:11AM +0100, Maxime Ripard wrote: >> > > > >>>>> On Thu, Feb 05, 2015 at 02:21:42PM +0100, Maxime Ripard wrote: >> > > > >>>>>> Hi, >> > > > >>>>>> >> > > > >>>>>> On Thu, Jan 22, 2015 at 08:37:45AM +0100, Yegor Yefremov wrote: >> > > > >>>>>>> I have the same experience with 3.15. The switching is working when >> > > > >>>>>>> CONFIG_USB_MUSB_DUAL_ROLE is set and dr_mode = "otg". But since 3.16 >> > > > >> >> > > > >> since 3.16 ? >> > > > > >> > > > > That's what Yegor said. I never saw it working with 3.15 either. >> > > > >> > > > I've used 3.15.1 and 3.15.2 with this set of patches: >> > > > https://github.com/visionsystemsgmbh/onrisc_br_bsp/tree/master/board/vscom/kernel-patches/linux-3.15 >> > > > >> > > > And it worked so far. The system: >> > > > http://www.visionsystems.de/produkte/baltos-ir-5221.html >> > > >> > > I've had more time to look into this (thanks Yegor for sponsoring a >> > > test/dev platform) what I noticed is that Connect IRQ takes seconds to >> > > fire up. Below a tiny log snippet after pluging USB OTG adapter cable >> > > that came with IR5521: >> > > >> > > | [ 1227.200514] musb-hdrc musb-hdrc.1.auto: usbintr (100) epintr(0) >> > > >> > > Cable connected. ID is grounded. 0x100 == DRVVBUS IRQ >> > > >> > > | [ 1227.206788] musb-hdrc musb-hdrc.1.auto: VBUS on (a_wait_vrise), devctl 19 >> > > >> > > MUSB starts to wait for VBUS to reach Session valid threshold >> > > >> > > | [ 1230.281159] musb-hdrc musb-hdrc.1.auto: usbintr (10) epintr(0) >> > > >> > > 3 seconds later connect interrupt happens. Looking at VBUS charge time >> > > with a scope, it's quite ok. VBUS charges in about 1.77ms. I'll dig >> > > further into this. >> > >> > even more weird. If I disconnect device from OTG adapter, rather than >> > OTG adapter from IR5521, this leave ID pin grounded, which means DRVVBUS >> > is still asserted and VBUS remains above session valid threshold. >> > >> > Even in this case, when I connect the device on the other end of the >> > cable, I still see some 3 seconds delay from the time device is >> > connected, to the time connect IRQ fires up. >> >> seems to be a problem with the USB stick I'm using. Tested two other >> devices and they connect right away. > > ok, fixing DRD on AM335x will take longer than I originally expected, > probably won't be ready for v4.2 :-( Are you able replicate the issue with TI AM335x GP EVM? I am wondering if the is custom board design problem? have you checked the custom board schematics? Regards, -Bin. > > -- > balbi -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
