On Wed, May 28, 2014 at 06:48:16AM +0800, Greg KH wrote:
> On Sat, May 24, 2014 at 05:09:02PM +0530, Pratyush Anand wrote:
> > OTG3 and EH Compliance Plan 1.0 talks about Super Speed OTG Verification
> > system (SS-OVS) which consists of an excersizer and analyzer.
> >
> > USB Compliance Suite from Lecroy or Ellisys can act as such SS-OVS for
> > Link Layer Validation (LVS).
> >
> > Some modifications are needed for an embedded Linux USB host to pass all
> > these tests. Most of these tests require just Link to be in U0. They do
> > not work with default Linux USB stack since, default stack does port
> > reset and then starts sending setup packet, which is not expected by
> > Link Layer Validation (LVS) device of Lecroy Compliance Suit. Then,
> > There are many Link Layer Tests which need host to generate specific
> > traffic.
> >
> > This patch supports specific traffic generation cases. As of now all the
> > host Lecroy Link Layer-USBIF tests (except TD7.26) passes
> > with this patch for single run using Lecroy USB Compliance Suite
> > Version 1.98 Build 239 and Lecroy USB Protocol Analyzer version 4.80
> > Build 1603. Therefore patch seems to be a good candidate for inclusion.
> > Further modification can be done on top of it.
> >
> > lvstest driver will not bind to any device by default. It can bind
> > manually to a super speed USB host controller root hub. Therefore, regular
> > hub driver must be unbound before this driver is bound. For example, if
> > 2-0:1.0 is the xhci root hub, then execute following to unbind hub driver.
> >
> > echo 2-0:1.0 > /sys/bus/usb/drivers/hub/unbind
> >
> > Then write Linux Foundation's vendor ID which is used by root hubs and
> > SS root hub's device ID into new_id file. Writing IDs into new_id file
> > will also bind the lvs driver with any available SS root hub interfaces.
> >
> > echo "1D6B 3" > /sys/bus/usb/drivers/lvs/new_id
> >
> > Now connect LVS device with root hub port.
> >
> > Test case specific traffic can be generated as follows whenever needed:
> >
> > 1. To issue "Get Device descriptor" command for TD.7.06:
> > echo > /sys/bus/usb/devices/2-0\:1.0/get_dev_desc
> >
> > 2. To set U1 timeout to 127 for TD.7.18
> > echo 127 > /sys/bus/usb/devices/2-0\:1.0/u1_timeout
> >
> > 3. To set U2 timeout to 0 for TD.7.18
> > echo 0 > /sys/bus/usb/devices/2-0\:1.0/u2_timeout
> >
> > 4. To issue "Hot Reset" for TD.7.29
> > echo > /sys/bus/usb/devices/2-0\:1.0/hot_reset
> >
> > 5. To issue "U3 Entry" for TD.7.35
> > echo > /sys/bus/usb/devices/2-0\:1.0/u3_entry
> >
> > 6. To issue "U3 Exit" for TD.7.36
> > echo > /sys/bus/usb/devices/2-0\:1.0/u3_exit
> >
> > Signed-off-by: Pratyush Anand <pratyush.anand@xxxxxx>
> > Acked-by: Alan Stern <stern@xxxxxxxxxxxxxxxxxxx>
> > ---
> > Documentation/ABI/testing/sysfs-bus-usb-lvstest | 47 +++
> > drivers/usb/misc/Kconfig | 7 +
> > drivers/usb/misc/Makefile | 1 +
> > drivers/usb/misc/lvstest.c | 452 ++++++++++++++++++++++++
> > 4 files changed, 507 insertions(+)
> > create mode 100644 Documentation/ABI/testing/sysfs-bus-usb-lvstest
> > create mode 100644 drivers/usb/misc/lvstest.c
>
> Did you build this code?
>
> It fails for me with:
>
> In file included from drivers/usb/misc/lvstest.c:16:0:
> include/linux/module.h:138:40: error: ‘__mod_usb__lvs_id_table_device_table’ aliased to undefined symbol ‘lvs_id_table’
> extern const struct type##_device_id __mod_##type##__##name##_device_table \
> ^
> drivers/usb/misc/lvstest.c:431:1: note: in expansion of macro ‘MODULE_DEVICE_TABLE’
> MODULE_DEVICE_TABLE(usb, lvs_id_table);
> ^
>
>
> > +MODULE_DEVICE_TABLE(usb, lvs_id_table);
Ohh.. I see.. its not defined..still it compiles well at my end.
Don't know how :(
I ll remove this line.
Regards
Pratyush
>
> Yeah, that line is the problem, and proof you didn't build this :(
>
> > +static struct usb_driver lvs_driver = {
> > + .name = "lvs",
> > + .probe = lvs_rh_probe,
> > + .disconnect = lvs_rh_disconnect,
> > +};
> > +
> > +static int __init lvs_init(void)
> > +{
> > + return usb_register(&lvs_driver);
> > +}
> > +module_init(lvs_init);
> > +
> > +static void __exit lvs_exit(void)
> > +{
> > + usb_deregister(&lvs_driver);
> > +}
> > +module_exit(lvs_exit);
>
> Use module_usb_driver() instead of these two functions please.
>
> And test your code.
>
> bah,
>
> greg k-h
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
