On 01/27/2014 02:52 PM, Greg KH wrote:
On Mon, Jan 27, 2014 at 02:29:53PM -0800, nubjub wrote:
The precise meaning of dead would be: Absolutely nothing is logged when
I plug a device into one of the other two ports. But for instance I have
a bus powered usb sound card that has an led indicating it's on, that
led illuminates. I also have a usb dvd drive which has an led that
illuminates if it negotiates usb2.0 speed; this led does NOT illuminate.
I will build a 3.13 kernel tomorrow. Let me know if the following logs
are what you're looking for on the new kernel: if I've missed anything
or included any crap you don't want.
Close, can you provide the full boot log after the pci device is
created? Or was this it?
I stopped copying when it appeared it had ceased to deal with that device.
The following is done still on the 3.10.11, but I thought I'd try again
right now.
It shows 2 XHCI controllers in the system, perhaps one of them isn't
working for the "failure"?
There are four ASMedia chips on the card, each with a single port
attached to it. I would expect it to find four of these controllers and
1 port detected for each one. As I said on one occasion recently it
found ASMedia devices.
Also, just the output of 'lspci' (no -v option), and 'lsusb' (again, no
'-v') will be fine to start with.
full lspci
0000:00:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2)
0000:00:01.0 ISA bridge: NVIDIA Corporation MCP55 LPC Bridge (rev a3)
0000:00:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3)
0000:00:02.0 USB controller: NVIDIA Corporation MCP55 USB Controller
(rev a1)
0000:00:02.1 USB controller: NVIDIA Corporation MCP55 USB Controller
(rev a2)
0000:00:04.0 IDE interface: NVIDIA Corporation MCP55 IDE (rev a1)
0000:00:05.0 IDE interface: NVIDIA Corporation MCP55 SATA Controller
(rev a3)
0000:00:05.1 IDE interface: NVIDIA Corporation MCP55 SATA Controller
(rev a3)
0000:00:05.2 IDE interface: NVIDIA Corporation MCP55 SATA Controller
(rev a3)
0000:00:06.0 PCI bridge: NVIDIA Corporation MCP55 PCI bridge (rev a2)
0000:00:06.1 Audio device: NVIDIA Corporation MCP55 High Definition
Audio (rev a2)
0000:00:08.0 Bridge: NVIDIA Corporation MCP55 Ethernet (rev a3)
0000:00:09.0 Bridge: NVIDIA Corporation MCP55 Ethernet (rev a3)
0000:00:0a.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge
(rev a3)
0000:00:0d.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge
(rev a3)
0000:00:0f.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge
(rev a3)
0000:00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h
Processor HyperTransport Configuration
0000:00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h
Processor Address Map
0000:00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h
Processor DRAM Controller
0000:00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h
Processor Miscellaneous Control
0000:00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h
Processor Link Control
0000:00:19.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h
Processor HyperTransport Configuration
0000:00:19.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h
Processor Address Map
0000:00:19.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h
Processor DRAM Controller
0000:00:19.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h
Processor Miscellaneous Control
0000:00:19.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h
Processor Link Control
0000:01:04.0 Network controller: Ralink corp. RT2800 802.11n PCI
0000:01:05.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22A
IEEE-1394a-2000 Controller (PHY/Link) [iOHCI-Lynx]
0000:05:00.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port
PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
0000:05:00.1 System peripheral: PLX Technology, Inc. PEX 8609 8-lane,
8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
0000:06:01.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port
PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
0000:06:05.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port
PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
0000:06:07.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port
PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
0000:06:09.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port
PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
0000:08:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed
USB Host Controller
0000:0a:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed
USB Host Controller
0000:18:00.0 VGA compatible controller: NVIDIA Corporation G92 [GeForce
8800 GT] (rev a2)
0000:2b:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express -
PCI/PCI-X Bridge (rev 06)
0000:2b:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express -
PCI/PCI-X Bridge (rev 06)
0000:2c:04.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030
PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07)
0000:2c:04.1 SCSI storage controller: LSI Logic / Symbios Logic 53c1030
PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07)
0000:2c:09.0 SCSI storage controller: Marvell Technology Group Ltd.
MV88SX6081 8-port SATA II PCI-X Controller (rev 09)
0001:40:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2)
0001:40:01.0 RAM memory: NVIDIA Corporation MCP55 LPC Bridge (rev a3)
0001:40:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3)
0001:40:0d.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge
(rev a3)
0001:40:0f.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge
(rev a3)
0001:58:00.0 VGA compatible controller: NVIDIA Corporation G92 [GeForce
8800 GT] (rev a2)
0001:6b:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1068E
PCI-Express Fusion-MPT SAS (rev 02)
full lsusb
Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 004 Device 002: ID 1852:5050 GYROCOM C&C Co., LTD
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 022: ID 0a5c:2190 Broadcom Corp.
Bus 006 Device 021: ID 0a5c:4503 Broadcom Corp. Mouse (Boot Interface
Subclass)
Bus 006 Device 020: ID 150a:1201
Bus 006 Device 019: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub
(part of BCM2046 Bluetooth)
Bus 006 Device 018: ID 18d1:d002 Google Inc.
Bus 006 Device 013: ID 03f3:4000 Adaptec, Inc. 4-port hub
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
thanks,
greg k-h
more of the bootlog
[ 1.159982] microcode: CPU0: patch_level=0x00000000
[ 1.159987] microcode: CPU1: patch_level=0x00000000
[ 1.159994] microcode: CPU2: patch_level=0x00000000
[ 1.160006] microcode: CPU3: patch_level=0x00000000
[ 1.160014] microcode: CPU4: patch_level=0x00000000
[ 1.160026] microcode: CPU5: patch_level=0x00000000
[ 1.160036] microcode: CPU6: patch_level=0x00000000
[ 1.160048] microcode: CPU7: patch_level=0x00000000
[ 1.160056] microcode: CPU8: patch_level=0x00000000
[ 1.160068] microcode: CPU9: patch_level=0x00000000
[ 1.160076] microcode: CPU10: patch_level=0x00000000
[ 1.160088] microcode: CPU11: patch_level=0x00000000
[ 1.160190] microcode: Microcode Update Driver: v2.00
<tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
[ 1.161292] audit: initializing netlink socket (disabled)
[ 1.161365] type=2000 audit(1390222220.035:1): initialized
[ 1.174007] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.175482] VFS: Disk quotas dquot_6.5.2
[ 1.175584] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.175765] msgmni has been set to 32768
[ 1.176451] alg: No test for stdrng (krng)
[ 1.176553] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 252)
[ 1.176781] io scheduler noop registered
[ 1.176833] io scheduler deadline registered
[ 1.176911] io scheduler cfq registered (default)
[ 1.177121] pcieport 0000:00:0a.0: irq 64 for MSI/MSI-X
[ 1.177220] pcieport 0000:00:0d.0: irq 65 for MSI/MSI-X
[ 1.177299] pcieport 0000:00:0f.0: irq 66 for MSI/MSI-X
[ 1.177387] pcieport 0000:05:00.0: irq 67 for MSI/MSI-X
[ 1.177509] pcieport 0000:06:01.0: irq 68 for MSI/MSI-X
[ 1.177606] pcieport 0000:06:05.0: irq 69 for MSI/MSI-X
[ 1.177957] ACPI: PCI Interrupt Link [LXPB] enabled at IRQ 10
[ 1.178033] pcieport 0000:06:07.0: irq 70 for MSI/MSI-X
[ 1.178129] pcieport 0000:06:09.0: irq 71 for MSI/MSI-X
[ 1.178301] pcieport 0001:40:0d.0: irq 72 for MSI/MSI-X
[ 1.178350] pcieport 0001:40:0f.0: irq 73 for MSI/MSI-X
[ 1.178413] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.178485] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.178639] GHES: HEST is not enabled!
[ 1.178769] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.199238] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200)
is a 16550A
[ 1.199743] Linux agpgart interface v0.103
[ 1.199928] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at
0x60,0x64 irq 1,12
[ 1.202824] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.202893] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.203100] mousedev: PS/2 mouse device common for all mice
[ 1.203186] rtc_cmos 00:02: RTC can wake from S4
[ 1.203406] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.203550] rtc_cmos 00:02: alarms up to one year, y3k, 114 bytes nvram
[ 1.203626] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@xxxxxxx>
[ 1.203679] AMD IOMMUv2 functionality not available on this system
[ 1.203879] TCP: cubic registered
[ 1.204055] NET: Registered protocol family 10
[ 1.204335] mip6: Mobile IPv6
[ 1.204384] NET: Registered protocol family 17
[ 1.204435] mpls_gso: MPLS GSO support
[ 1.205121] registered taskstats version 1
[ 1.206015] rtc_cmos 00:02: setting system clock to 2014-01-20
12:50:21 UTC (1390222221)
[ 1.206109] PM: Hibernation image not present or could not be loaded.
[ 1.207378] Freeing unused kernel memory: 1264K (ffffffff818b0000 -
ffffffff819ec000)
[ 1.207446] Write protecting the kernel read-only data: 8192k
[ 1.211072] Freeing unused kernel memory: 1284K (ffff8800014bf000 -
ffff880001600000)
[ 1.212314] Freeing unused kernel memory: 420K (ffff880001797000 -
ffff880001800000)
[ 1.248216] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
[ 1.251809] SCSI subsystem initialized
[ 1.254307] ACPI: bus type USB registered
[ 1.255287] usbcore: registered new interface driver usbfs
[ 1.256715] usbcore: registered new interface driver hub
[ 1.258092] usbcore: registered new device driver usb
[ 1.258317] libata version 3.00 loaded.
[ 1.264466] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.268743] ehci-pci: EHCI PCI platform driver
[ 1.269330] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.270689] forcedeth: Reverse Engineered nForce ethernet driver.
Version 0.64.
[ 1.273322] ACPI: PCI Interrupt Link [LMC0] enabled at IRQ 18
[ 1.273543] forcedeth 0000:00:08.0: setting latency timer to 64
[ 1.274595] ohci-pci: OHCI PCI platform driver
[ 1.315619] pci 0000:00:06.0: setting latency timer to 64
[ 1.315866] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 17
[ 1.333665] Fusion MPT base driver 3.04.20
[ 1.333877] Copyright (c) 1999-2008 LSI Corporation
[ 1.334598] sata_mv 0000:2c:09.0: version 1.28
[ 1.335017] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 20
[ 1.335526] sata_mv 0000:2c:09.0: Gen-II 32 slots 8 ports SCSI mode
IRQ via INTx
[ 1.341158] FDC 0 is a post-1991 82077
[ 1.351286] Fusion MPT SPI Host driver 3.04.20
[ 1.368703] Fusion MPT SAS Host driver 3.04.20
[ 1.369466] ACPI: PCI Interrupt Link [LXD2] enabled at IRQ 43
[ 1.369821] mptbase: ioc0: Initiating bringup
[ 1.378788] firewire_ohci 0000:01:05.0: added OHCI v1.10 device as
card 0, 4 IR + 8 IT contexts, quirks 0x2
[ 1.383101] xhci_hcd 0000:08:00.0: xHCI Host Controller
[ 1.383302] scsi0 : sata_mv
[ 1.383429] xhci_hcd 0000:08:00.0: new USB bus registered, assigned
bus number 1
[ 1.393427] scsi1 : sata_mv
[ 1.395974] scsi2 : sata_mv
[ 1.398951] scsi3 : sata_mv
[ 1.401726] scsi4 : sata_mv
[ 1.405166] scsi5 : sata_mv
[ 1.407752] scsi6 : sata_mv
[ 1.410397] scsi7 : sata_mv
[ 1.413130] ata1: SATA max UDMA/133 mmio m1048576@0xcf400000 port
0xcf422000 irq 20
[ 1.413358] ata2: SATA max UDMA/133 mmio m1048576@0xcf400000 port
0xcf424000 irq 20
[ 1.413577] ata3: SATA max UDMA/133 mmio m1048576@0xcf400000 port
0xcf426000 irq 20
[ 1.413769] ata4: SATA max UDMA/133 mmio m1048576@0xcf400000 port
0xcf428000 irq 20
[ 1.413977] ata5: SATA max UDMA/133 mmio m1048576@0xcf400000 port
0xcf432000 irq 20
[ 1.414220] ata6: SATA max UDMA/133 mmio m1048576@0xcf400000 port
0xcf434000 irq 20
[ 1.414438] ata7: SATA max UDMA/133 mmio m1048576@0xcf400000 port
0xcf436000 irq 20
[ 1.414647] ata8: SATA max UDMA/133 mmio m1048576@0xcf400000 port
0xcf438000 irq 20
[ 1.446883] xhci_hcd 0000:08:00.0: irq 74 for MSI/MSI-X
[ 1.446891] xhci_hcd 0000:08:00.0: irq 75 for MSI/MSI-X
[ 1.446899] xhci_hcd 0000:08:00.0: irq 76 for MSI/MSI-X
[ 1.446905] xhci_hcd 0000:08:00.0: irq 77 for MSI/MSI-X
[ 1.446911] xhci_hcd 0000:08:00.0: irq 78 for MSI/MSI-X
[ 1.446917] xhci_hcd 0000:08:00.0: irq 79 for MSI/MSI-X
[ 1.446924] xhci_hcd 0000:08:00.0: irq 80 for MSI/MSI-X
[ 1.446930] xhci_hcd 0000:08:00.0: irq 81 for MSI/MSI-X
[ 1.448604] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 16
[ 1.448980] mptbase: ioc1: Initiating bringup
[ 1.449588] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.449790] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.450015] usb usb1: Product: xHCI Host Controller
[ 1.450208] usb usb1: Manufacturer: Linux 3.12-1-rt-amd64 xhci_hcd
[ 1.450392] usb usb1: SerialNumber: 0000:08:00.0
[ 1.454624] hub 1-0:1.0: USB hub found
[ 1.454918] hub 1-0:1.0: 2 ports detected
[ 1.458912] xhci_hcd 0000:08:00.0: xHCI Host Controller
[ 1.459106] xhci_hcd 0000:08:00.0: new USB bus registered, assigned
bus number 2
[ 1.459393] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.459588] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.459791] usb usb2: Product: xHCI Host Controller
[ 1.459999] usb usb2: Manufacturer: Linux 3.12-1-rt-amd64 xhci_hcd
[ 1.460199] usb usb2: SerialNumber: 0000:08:00.0
[ 1.464525] hub 2-0:1.0: USB hub found
[ 1.464740] hub 2-0:1.0: 2 ports detected
[ 1.483030] xhci_hcd 0000:0a:00.0: xHCI Host Controller
[ 1.483304] xhci_hcd 0000:0a:00.0: new USB bus registered, assigned
bus number 3
[ 1.546906] xhci_hcd 0000:0a:00.0: irq 82 for MSI/MSI-X
[ 1.546913] xhci_hcd 0000:0a:00.0: irq 83 for MSI/MSI-X
[ 1.546921] xhci_hcd 0000:0a:00.0: irq 84 for MSI/MSI-X
[ 1.546928] xhci_hcd 0000:0a:00.0: irq 85 for MSI/MSI-X
[ 1.546934] xhci_hcd 0000:0a:00.0: irq 86 for MSI/MSI-X
[ 1.546940] xhci_hcd 0000:0a:00.0: irq 87 for MSI/MSI-X
[ 1.546947] xhci_hcd 0000:0a:00.0: irq 88 for MSI/MSI-X
[ 1.546953] xhci_hcd 0000:0a:00.0: irq 89 for MSI/MSI-X
[ 1.548538] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.548806] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.549068] usb usb3: Product: xHCI Host Controller
[ 1.549297] usb usb3: Manufacturer: Linux 3.12-1-rt-amd64 xhci_hcd
[ 1.549524] usb usb3: SerialNumber: 0000:0a:00.0
[ 1.554278] hub 3-0:1.0: USB hub found
[ 1.554513] hub 3-0:1.0: 2 ports detected
[ 1.558358] xhci_hcd 0000:0a:00.0: xHCI Host Controller
[ 1.558564] xhci_hcd 0000:0a:00.0: new USB bus registered, assigned
bus number 4
[ 1.558937] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.559161] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.559407] usb usb4: Product: xHCI Host Controller
[ 1.559633] usb usb4: Manufacturer: Linux 3.12-1-rt-amd64 xhci_hcd
[ 1.559855] usb usb4: SerialNumber: 0000:0a:00.0
[ 1.563876] hub 4-0:1.0: USB hub found
[ 1.564069] hub 4-0:1.0: 2 ports detected
[ 1.614827] ioc1: LSI53C1030 B2: Capabilities={Initiator}
[ 1.799510] forcedeth 0000:00:08.0: ifname eth0, PHY OUI 0x5043 @ 0,
addr 00:1c:c4:ae:65:90
[ 1.799642] forcedeth 0000:00:08.0: highdma csum vlan pwrctl mgmt
gbit lnktim msi desc-v3
[ 1.799936] ehci-pci 0000:00:02.1: setting latency timer to 64
[ 1.799963] ehci-pci 0000:00:02.1: EHCI Host Controller
[ 1.800092] ehci-pci 0000:00:02.1: new USB bus registered, assigned
bus number 5
[ 1.800223] ehci-pci 0000:00:02.1: debug port 1
[ 1.800364] ehci-pci 0000:00:02.1: cache line size of 64 is not supported
[ 1.800488] ehci-pci 0000:00:02.1: irq 5, io mem 0xcfb4a000
[ 1.810875] ehci-pci 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 1.811047] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.811147] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.811269] usb usb5: Product: EHCI Host Controller
[ 1.811365] usb usb5: Manufacturer: Linux 3.12-1-rt-amd64 ehci_hcd
[ 1.811460] usb usb5: SerialNumber: 0000:00:02.1
[ 1.811703] hub 5-0:1.0: USB hub found
[ 1.811808] hub 5-0:1.0: 10 ports detected
[ 1.812123] sata_nv 0000:00:05.0: version 3.5
[ 1.812345] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[ 1.812491] sata_nv 0000:00:05.0: Using SWNCQ mode
[ 1.813205] sata_nv 0000:00:05.0: setting latency timer to 64
[ 1.813596] scsi8 : sata_nv
[ 1.813728] scsi9 : sata_nv
[ 1.813821] ata9: SATA max UDMA/133 cmd 0x60c0 ctl 0x6100 bmdma
0x6090 irq 23
[ 1.813877] ata10: SATA max UDMA/133 cmd 0x60c8 ctl 0x6104 bmdma
0x6098 irq 23
[ 1.814048] ohci-pci 0000:00:02.0: setting latency timer to 64
[ 1.814051] ohci-pci 0000:00:02.0: OHCI PCI host controller
[ 1.814130] ohci-pci 0000:00:02.0: new USB bus registered, assigned
bus number 6
[ 1.814252] ohci-pci 0000:00:02.0: irq 7, io mem 0xcfb44000
[ 1.868929] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.869035] usb usb6: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.869160] usb usb6: Product: OHCI PCI host controller
[ 1.869267] usb usb6: Manufacturer: Linux 3.12-1-rt-amd64 ohci_hcd
[ 1.869375] usb usb6: SerialNumber: 0000:00:02.0
[ 1.869610] hub 6-0:1.0: USB hub found
[ 1.869723] hub 6-0:1.0: 10 ports detected
[ 1.870380] ACPI: PCI Interrupt Link [LMC1] enabled at IRQ 18
[ 1.870519] forcedeth 0000:00:09.0: setting latency timer to 64
[ 1.891027] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.899490] ata1.00: ATA-6: WDC WD800JD-00HKA0, 13.03G13, max UDMA/133
[ 1.899598] ata1.00: 156301488 sectors, multi 0: LBA
[ 1.907861] ata1.00: configured for UDMA/133
[ 1.908120] scsi 0:0:0:0: Direct-Access ATA WDC WD800JD-00HK
13.0 PQ: 0 ANSI: 5
[ 1.918781] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks:
(80.0 GB/74.5 GiB)
[ 1.919027] sd 0:0:0:0: [sda] Write Protect is off
[ 1.919114] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.919129] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.928910] sda: sda1 sda2
[ 1.929321] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.947067] firewire_core 0000:01:05.0: created device fw0: GUID
0060b00000250abe, S400
[ 1.946963] ioc0: LSISAS1068E B1: Capabilities={Initiator}
[ 2.050621] scsi10 : ioc1: LSI53C1030 B2, FwRev=01030a00h, Ports=1,
MaxQ=255, IRQ=16
[ 2.123094] usb 5-9: new high-speed USB device number 2 using ehci-pci
[ 2.159004] tsc: Refined TSC clocksource calibration: 2600.006 MHz
[ 2.255953] usb 5-9: New USB device found, idVendor=4855, idProduct=3288
[ 2.256058] usb 5-9: New USB device strings: Mfr=56, Product=64,
SerialNumber=83
[ 2.256171] usb 5-9: Product: 1394/USB 2.0 Drive
[ 2.256270] usb 5-9: Manufacturer: Memorex
[ 2.256369] usb 5-9: SerialNumber: 0505029260
[ 2.265796] usb-storage 5-9:1.0: USB Mass Storage device detected
[ 2.266010] scsi11 : usb-storage 5-9:1.0
[ 2.266196] usbcore: registered new interface driver usb-storage
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
