Hi Viresh,
Thank you for the review. please find my reply inline.
+++ b/drivers/cpufreq/tegra194-cpufreq.c
@@ -0,0 +1,403 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019, NVIDIA CORPORATION. All rights reserved
2020
+ */
+
+#include <linux/cpu.h>
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <asm/smp_plat.h>
+
+#include <soc/tegra/bpmp.h>
+#include <soc/tegra/bpmp-abi.h>
+
+#define KHZ 1000
+#define REF_CLK_MHZ 408 /* 408 MHz */
+#define US_DELAY 500
+#define US_DELAY_MIN 2
+#define CPUFREQ_TBL_STEP_HZ (50 * KHZ * KHZ)
+#define MAX_CNT ~0U
+
+/* cpufreq transisition latency */
+#define TEGRA_CPUFREQ_TRANSITION_LATENCY (300 * 1000) /* unit in nanoseconds */
+
+#define LOOP_FOR_EACH_CPU_OF_CLUSTER(cl) for (cpu = (cl * 2); \
+ cpu < ((cl + 1) * 2); cpu++)
Both latency and this loop are used only once in the code, maybe just open code
it. Also you should have passed cpu as a parameter to the macro, even if it
works fine without it, for better readability.
Ok, i will open code the loop in next version. For latency value, i feel
named macro makes readability better. So, prefer keeping it.
+
+u16 map_freq_to_ndiv(struct mrq_cpu_ndiv_limits_response *nltbl, u32 freq)
Unused routine
Sure, will remove it.
+{
+ return DIV_ROUND_UP(freq * nltbl->pdiv * nltbl->mdiv,
+ nltbl->ref_clk_hz / KHZ);
+}
+static int tegra194_cpufreq_init(struct cpufreq_policy *policy)
+{
+ struct tegra194_cpufreq_data *data = cpufreq_get_driver_data();
+ int cl = get_cpu_cluster(policy->cpu);
+ u32 cpu;
+
+ if (cl >= data->num_clusters)
+ return -EINVAL;
+
+ policy->cur = tegra194_fast_get_speed(policy->cpu); /* boot freq */
+
+ /* set same policy for all cpus in a cluster */
+ LOOP_FOR_EACH_CPU_OF_CLUSTER(cl)
+ cpumask_set_cpu(cpu, policy->cpus);
+
+ policy->freq_table = data->tables[cl];
+ policy->cpuinfo.transition_latency = TEGRA_CPUFREQ_TRANSITION_LATENCY;
+
+ return 0;
+}
+static int tegra194_cpufreq_set_target(struct cpufreq_policy *policy,
+ unsigned int index)
+{
+ struct cpufreq_frequency_table *tbl = policy->freq_table + index;
+
+ on_each_cpu_mask(policy->cpus, set_cpu_ndiv, tbl, true);
I am still a bit confused. While setting the frequency you are calling this
routine for each CPU of the policy (cluster). Does that mean that CPUs within a
cluster can actually run at different frequencies at any given point of time ?
If cpufreq terms, a cpufreq policy represents a group of CPUs that change
frequency together, i.e. they share the clk line. If all CPUs in your system can
do DVFS separately, then you must have policy per CPU, instead of cluster.
T194 supports four CPU clusters, each with two cores. Each CPU cluster
is capable of running at a specific frequency sourced by respective
NAFLL to provide cluster specific clocks. Individual cores within a
cluster write freq in per core register. Cluster h/w forwards the
max(core0, core1) request to per cluster NAFLL.
+static void tegra194_cpufreq_free_resources(void)
+{
+ flush_workqueue(read_counters_wq);
Why is this required exactly? I see that you add the work request and
immediately flush it, then why would you need to do this separately ?
Ya, will remove flush_workqueue().
+ destroy_workqueue(read_counters_wq);
+}
+
+static struct cpufreq_frequency_table *
+init_freq_table(struct platform_device *pdev, struct tegra_bpmp *bpmp,
+ unsigned int cluster_id)
+{
+ struct cpufreq_frequency_table *freq_table;
+ struct mrq_cpu_ndiv_limits_response resp;
+ unsigned int num_freqs, ndiv, delta_ndiv;
+ struct mrq_cpu_ndiv_limits_request req;
+ struct tegra_bpmp_message msg;
+ u16 freq_table_step_size;
+ int err, index;
+
+ memset(&req, 0, sizeof(req));
+ req.cluster_id = cluster_id;
+
+ memset(&msg, 0, sizeof(msg));
+ msg.mrq = MRQ_CPU_NDIV_LIMITS;
+ msg.tx.data = &req;
+ msg.tx.size = sizeof(req);
+ msg.rx.data = &resp;
+ msg.rx.size = sizeof(resp);
+
+ err = tegra_bpmp_transfer(bpmp, &msg);
So the firmware can actually return different frequency tables for the clusters,
right ? Else you could have received the table only once and used it for all the
CPUs.
Yes, frequency tables are returned per cluster by BPMP firmware. In T194
SOC, currently same table values are used for all clusters. This might
change in future.
+ if (err)
+ return ERR_PTR(err);
+
+ /*
+ * Make sure frequency table step is a multiple of mdiv to match
+ * vhint table granularity.
+ */
+ freq_table_step_size = resp.mdiv *
+ DIV_ROUND_UP(CPUFREQ_TBL_STEP_HZ, resp.ref_clk_hz);
+
+ dev_dbg(&pdev->dev, "cluster %d: frequency table step size: %d\n",
+ cluster_id, freq_table_step_size);
+
+ delta_ndiv = resp.ndiv_max - resp.ndiv_min;
+
+ if (unlikely(delta_ndiv == 0))
+ num_freqs = 1;
+ else
+ /* We store both ndiv_min and ndiv_max hence the +1 */
+ num_freqs = delta_ndiv / freq_table_step_size + 1;
+
+ num_freqs += (delta_ndiv % freq_table_step_size) ? 1 : 0;
+
+ freq_table = devm_kcalloc(&pdev->dev, num_freqs + 1,
+ sizeof(*freq_table), GFP_KERNEL);
+ if (!freq_table)
+ return ERR_PTR(-ENOMEM);
+
+ for (index = 0, ndiv = resp.ndiv_min;
+ ndiv < resp.ndiv_max;
+ index++, ndiv += freq_table_step_size) {
+ freq_table[index].driver_data = ndiv;
+ freq_table[index].frequency = map_ndiv_to_freq(&resp, ndiv);
+ }
+
+ freq_table[index].driver_data = resp.ndiv_max;
+ freq_table[index++].frequency = map_ndiv_to_freq(&resp, resp.ndiv_max);
+ freq_table[index].frequency = CPUFREQ_TABLE_END;
+
+ return freq_table;
+}
--
viresh
