On 07/07/2016 12:50 AM, Stephen Warren wrote:
On 07/06/2016 03:06 AM, Joseph Lo wrote:
On 07/06/2016 03:05 PM, Alexandre Courbot wrote:
On Tue, Jul 5, 2016 at 6:04 PM, Joseph Lo <josephl@xxxxxxxxxx> wrote:
The Tegra HSP mailbox driver implements the signaling doorbell-based
interprocessor communication (IPC) for remote processors currently. The
HSP HW modules support some different features for that, which are
shared mailboxes, shared semaphores, arbitrated semaphores, and
doorbells. And there are multiple HSP HW instances on the chip. So the
driver is extendable to support more features for different IPC
requirement.
The driver of remote processor can use it as a mailbox client and deal
with the IPC protocol to synchronize the data communications.
diff --git a/drivers/mailbox/tegra-hsp.c b/drivers/mailbox/tegra-hsp.c
+static irqreturn_t hsp_db_irq(int irq, void *p)
+{
+ struct tegra_hsp_mbox *hsp_mbox = p;
+ ulong val;
+ int master_id;
+
+ val = (ulong)hsp_readl(hsp_mbox->db_base[HSP_DB_CCPLEX],
+ HSP_DB_REG_PENDING);
+ hsp_writel(hsp_mbox->db_base[HSP_DB_CCPLEX],
HSP_DB_REG_PENDING, val);
+
+ spin_lock(&hsp_mbox->lock);
+ for_each_set_bit(master_id, &val, MAX_NUM_HSP_CHAN) {
+ struct mbox_chan *chan;
+ struct tegra_hsp_mbox_chan *mchan;
+ int i;
+
+ for (i = 0; i < MAX_NUM_HSP_CHAN; i++) {
I wonder if this could not be optimized. You are doing a double loop
on MAX_NUM_HSP_CHAN to look for an identical master_id. Since it seems
like the same master_id cannot be used twice (considering that the
inner loop only processes the first match), couldn't you just select
the free channel in of_hsp_mbox_xlate() by doing
&mbox->chans[master_id] (and returning an error if it is already
used), then simply getting chan as &hsp_mbox->mbox->chans[master_id]
instead of having the inner loop below? That would remove the need for
the second loop.
That was exactly what I did in the V1, which only supported one HSP
sub-module per HSP HW block. So we can just use the master_id as the
mbox channel ID.
Meanwhile, the V2 is purposed to support multiple HSP sub-modules to be
running on the same HSP HW block. The "ID" between different modules
could be conflict. So I dropped the mechanism that used the master_id as
the mbox channel ID.
I haven't looked at the code in this patch since I'm mainly concerned
about the DT bindings. However, I will say that nothing in the change to
the mailbox specifier in DT should have required /any/ changes to the
code, except to add a single check to validate that the "mailbox type"
encoded into the top 16 bits of the mailbox ID were 0, and hence
represented a doorbell rather than anything else. Any enhancements to
support other mailbox types could have happened later, and I doubt would
require anything dynamic even then.
Yes, I only add the code for that change. Maybe some glue code for the
extend-ability to support more HSP modules in the future.
+static int tegra_hsp_db_init(struct tegra_hsp_mbox *hsp_mbox,
+ struct mbox_chan *mchan, int master_id)
+{
+ struct platform_device *pdev =
to_platform_device(hsp_mbox->mbox->dev);
+ struct tegra_hsp_mbox_chan *hsp_mbox_chan;
+ int ret;
+
+ if (!hsp_mbox->db_irq) {
+ int i;
+
+ hsp_mbox->db_irq = platform_get_irq_byname(pdev,
"doorbell");
Getting the IRQ sounds more like a job for probe() - I don't see the
benefit of lazy-doing it?
We only need the IRQ when the client is requesting the DB service. For
other HSP sub-modules, they are using different IRQ. So I didn't do that
at probe time.
All resources provided by other devices/drivers must be acquired at
probe time, since that's the only time it's possible to defer probe if
the provider of the resource is not available.
If you don't follow that rule, what happens is:
1) This driver probes.
2) Some other driver calls tegra_hsp_db_init(), and it fails since the
provider of the IRQ is not yet available. This likely ends up returning
something other than -EPROBE_DEFER since the HSP driver was found
successfully (thus there is no deferred probe situation as far as the
mailbox core is concerned), it's just that the mailbox channel
lookup/init/... failed.
3) The other driver's probe() fails due to this, but since the error
wasn't a probe deferral, the other driver's probe() is never retried.
Agree, will fix this.
Thanks,
-Joseph
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
