Am Freitag, den 19.09.2014, 15:53 -0400 schrieb Sean Paul:
> Per NVidia, this clock rate should be around 70MHz in
> order to properly sample reads on data lane 0. In order
> to achieve this rate, we need to reparent the clock from
> clk_m which can only achieve 12MHz. Add parent_lp to the
> dts bindings and set the parent & rate on init.
>
> Signed-off-by: Sean Paul <seanpaul@xxxxxxxxxxxx>
NACK
You are pushing SoC integration details into the binding of the device.
You have two reasonable routes to go here: either the clock driver needs
to be made smarter to reparent the clock in case the required clock rate
could not be achieved with the current parent or you go the easy route
and reparent the clock as part of the initial configuration.
Regards,
Lucas
> ---
> .../devicetree/bindings/gpu/nvidia,tegra20-host1x.txt | 10 ++++++++--
> drivers/gpu/drm/tegra/dsi.c | 18 ++++++++++++++++++
> drivers/gpu/drm/tegra/dsi.h | 3 +++
> 3 files changed, 29 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt
> index b48f4ef..fef2918 100644
> --- a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt
> +++ b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt
> @@ -191,6 +191,10 @@ of the following host1x client modules:
> - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
> - nvidia,edid: supplies a binary EDID blob
> - nvidia,panel: phandle of a display panel
> + - clock-names: Can include the following entries:
> + - lp_parent: The parent clock for lp
> + - clocks: Must contain an entry for each optional entry in clock-names.
> + See ../clocks/clock-bindings.txt for details.
>
> - sor: serial output resource
>
> @@ -360,8 +364,10 @@ Example:
> compatible = "nvidia,tegra20-dsi";
> reg = <0x54300000 0x00040000>;
> clocks = <&tegra_car TEGRA20_CLK_DSI>,
> - <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
> - clock-names = "dsi", "parent";
> + <&tegra_car TEGRA124_CLK_DSIALP>,
> + <&tegra_car TEGRA20_CLK_PLL_D_OUT0>,
> + <&tegra_car TEGRA124_CLK_PLL_P>;
> + clock-names = "dsi", "lp", "parent", "lp_parent";
> resets = <&tegra_car 48>;
> reset-names = "dsi";
> status = "disabled";
> diff --git a/drivers/gpu/drm/tegra/dsi.c b/drivers/gpu/drm/tegra/dsi.c
> index f787445..c0258ae 100644
> --- a/drivers/gpu/drm/tegra/dsi.c
> +++ b/drivers/gpu/drm/tegra/dsi.c
> @@ -837,6 +837,7 @@ static int tegra_dsi_probe(struct platform_device *pdev)
> struct tegra_dsi *dsi;
> struct resource *regs;
> int err;
> + struct clk *lp_parent;
>
> dsi = devm_kzalloc(&pdev->dev, sizeof(*dsi), GFP_KERNEL);
> if (!dsi)
> @@ -879,6 +880,23 @@ static int tegra_dsi_probe(struct platform_device *pdev)
> return PTR_ERR(dsi->clk_lp);
> }
>
> + lp_parent = devm_clk_get(&pdev->dev, "lp_parent");
> + if (!IS_ERR(lp_parent)) {
> + err = clk_set_parent(dsi->clk_lp, lp_parent);
> + if (err < 0) {
> + dev_err(&pdev->dev, "cannot set lp clock parent\n");
> + return err;
> + }
> + } else {
> + dev_info(&pdev->dev, "no lp clock parent, using hw default\n");
> + }
> +
> + err = clk_set_rate(dsi->clk_lp, DSI_LP_CLK_RATE);
> + if (err < 0) {
> + dev_err(&pdev->dev, "cannot set low-power clock rate\n");
> + return err;
> + }
> +
> err = clk_prepare_enable(dsi->clk_lp);
> if (err < 0) {
> dev_err(&pdev->dev, "cannot enable low-power clock\n");
> diff --git a/drivers/gpu/drm/tegra/dsi.h b/drivers/gpu/drm/tegra/dsi.h
> index 5ce610d..a332caf 100644
> --- a/drivers/gpu/drm/tegra/dsi.h
> +++ b/drivers/gpu/drm/tegra/dsi.h
> @@ -127,4 +127,7 @@ enum tegra_dsi_format {
> TEGRA_DSI_FORMAT_24P,
> };
>
> +/* default lp clock rate */
> +#define DSI_LP_CLK_RATE (70 * 1000 * 1000)
> +
> #endif
--
Pengutronix e.K. | Lucas Stach |
Industrial Linux Solutions | http://www.pengutronix.de/ |
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
