Am Freitag 15 Juli 2011, 18:45:53 schrieb Colin Cross: > On Fri, Jul 15, 2011 at 2:55 AM, Heiko Stübner <heiko@xxxxxxxxx> wrote: > > Am Freitag, 15. Juli 2011, 11:13:48 schrieb Marc Dietrich: > >> see comment for PATCH 1/2 > >> > >> Am Sun, 10 Jul 2011 15:19:34 -0700 > >> > >> schrieb Colin Cross <ccross@xxxxxxxxxxx>: > >> > trimslice and paz00 both have functionally identical platform > >> > data for the tegra-ehci driver. Move the platform data into > >> > devices.c, and remove it from all the board files. > >> > > >> > Signed-off-by: Colin Cross <ccross@xxxxxxxxxxx> > >> > >> Acked-By: Marc Dietrich <marvin24@xxxxxx> > >> > >> > --- > >> > > >> > arch/arm/mach-tegra/board-paz00.c | 26 > >> > > >> > > >> > > >> > -static struct tegra_ulpi_config ulpi_phy_config = { > >> > - .reset_gpio = TEGRA_ULPI_RST, > >> > - .clk = "cdev2", > >> > -}; > >> > - > >> > -static struct tegra_ehci_platform_data tegra_ehci_pdata[] = { > >> > - [0] = { > >> > - .operating_mode = TEGRA_USB_OTG, > >> > - .power_down_on_bus_suspend = 1, > >> > - }, > >> > - [1] = { > >> > - .phy_config = &ulpi_phy_config, > >> > - .operating_mode = TEGRA_USB_HOST, > >> > - .power_down_on_bus_suspend = 1, > >> > - }, > >> > - [2] = { > >> > - .operating_mode = TEGRA_USB_HOST, > >> > - .power_down_on_bus_suspend = 1, > >> > - }, > >> > -}; > > > > I'm not sure about this. > > > > For paz00 tegra_ehci3_device also leads to an external usb port. With > > power_down_on_bus_suspend = 1 hotplugging usb devices doesn't work (as > > the bus might be suspended at the time). > > > > From the initial commit message of ehci-tegra on android.git.kernel.org: > > "For additional power saving, the driver supports powering down the > > phy on bus suspend when it is used, for example, to connect an internal > > device that use an out-of-band remote wakeup mechanism (e.g. a gpio)." > > > > So my guess was, that the correct handling of this was setting > > power_down_on_bus_suspend to 0 - which did fix the problem. > > > > With this data moving to devices.c, setting this would also change the > > trimslice behaviour which would be a problem. > > > > In the end I'm not sure if setting power_down_on_bus_suspend to 0 is the > > correct solution to the hotplug problem or if a better solution exists. > > > > Thanks > > Heiko > > Can you or someone else test if power_down_on_bus_suspend is causing a > problem? If it is, I'll change the default in devices.c to > power_down_on_bus_suspend=0, and devices that want > power_down_on_bus_suspend=1 will have to set it. With power_down_on_bus_suspend = 1, paz00 fails to recognize newly attached devices, i.e. only devices connected during boot are accessible. But it doesn't cause problems with the devices themselfs. Am Freitag 15 Juli 2011, 20:30:18 schrieb Olof Johansson: > (Note: I'll post a patch in a bit that keeps the IP clocked even if phy is > powered down on bus suspend, since otherwise we don't get hotplug events > for hub-less systems). This might also fix the hotplug problem on paz00 *fingers crossed*. Heiko -- To unsubscribe from this list: send the line "unsubscribe linux-tegra" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html