Re: [PATCH 1/2] dt-bindings: staging: iio: imu: Document CEVA BNO08x

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Jun 16, 2022 at 12:00:05PM +0200, Jacopo Mondi wrote:
> From: Jacopo Mondi <jacopo@xxxxxxxxxx>
> 
> Document CEVA BNO08x (080, 085 and 086) Sensor Hub.
> 
> The BNO08X family (BNO080/85/86) is a System in Package (SiP) that
> integrates a triaxial accelerometer, triaxial gyroscope, magnetometer
> and a 32-bit ARM Cortex-M0+ microcontroller running CEVA's SH-2
> firmware.
> 
> Datasheet:
> https://www.ceva-dsp.com/wp-content/uploads/2019/10/BNO080_085-Datasheet.pdf
> 
> Signed-off-by: Jacopo Mondi <jacopo@xxxxxxxxxx>
> ---
>  .../bindings/staging/iio/imu/ceva,bno08x.yaml | 63 +++++++++++++++++++

You expect this binding to change? If so, then why define the ABI. If 
not, then why is it in staging? IOW, I don't really want additions to 
bindings/staging/.

If this isn't in a .dts file and the driver isn't stable yet, then just 
don't document it until it is.

>  1 file changed, 63 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/staging/iio/imu/ceva,bno08x.yaml
> 
> diff --git a/Documentation/devicetree/bindings/staging/iio/imu/ceva,bno08x.yaml b/Documentation/devicetree/bindings/staging/iio/imu/ceva,bno08x.yaml
> new file mode 100644
> index 000000000000..f7d6ea6d9147
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/staging/iio/imu/ceva,bno08x.yaml
> @@ -0,0 +1,63 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/staging/iio/imu/ceva,bno08x.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: CEVA BNO080/85/86
> +
> +maintainers:
> +  - Jacopo Mondi <jacopo@xxxxxxxxxx>
> +
> +description: |
> +  CEVA BNO08x is a System in Package (SiP) that integrates a triaxial
> +  accelerometer, triaxial gyroscope, magnetometer and a 32-bit ARM Cortex-M0+
> +  microcontroller running CEVA's SH-2 firmware.
> +
> +  The BNO08x family is documented at
> +  https://www.ceva-dsp.com/product/bno080-085/
> +  https://www.ceva-dsp.com/wp-content/uploads/2019/10/BNO080_085-Datasheet.pdf
> +
> +  The SH-2 firmware reference is available at
> +  https://cdn.sparkfun.com/assets/4/d/9/3/8/SH-2-Reference-Manual-v1.2.pdf
> +  https://cdn.sparkfun.com/assets/7/6/9/3/c/Sensor-Hub-Transport-Protocol-v1.7.pdf
> +
> +properties:
> +  compatible:
> +    const: ceva,bno08x

Don't use wildcards in compatibles.

> +
> +  reg:
> +    maxItems: 1
> +
> +  reset-gpios:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +    description:
> +      Phandle to the GPIO connected to the chip H_INTN (Host Interrupt) pin.
> +      The interrupt type shall be IRQ_TYPE_EDGE_FALLING.
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        bno080: imu@4b {
> +            compatible = "ceva,bno08x";
> +            interrupt-parent = <&gpio5>;
> +            interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
> +            reg = <0x4b>;
> +        };
> +    };
> +
> --
> 2.35.1
> 
> 




[Index of Archives]     [Linux Driver Development]     [Linux Driver Backports]     [DMA Engine]     [Linux GPIO]     [Linux SPI]     [Video for Linux]     [Linux USB Devel]     [Linux Coverity]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux