Am Dienstag, dem 15.06.2021 um 01:11 +0300 schrieb Laurent Pinchart:
> Hi Martin,
>
> Thank you for the patch.
>
> On Mon, Jun 14, 2021 at 02:25:17PM +0200, Martin Kepplinger wrote:
> > Describe the 2 available CSI interfaces on the i.MX8MQ with the
> > MIPI-CSI2
> > receiver and the CSI Bridge that provides the user buffers, where
> > the
> > existing driver can directly be used.
> >
> > An image sensor is to be connected to the MIPIs' second port,
> > described in
> > board files.
> >
> > Signed-off-by: Martin Kepplinger <martin.kepplinger@xxxxxxx>
> > ---
> >
> > sorry, the csi compatible addition suggested by Marco was missing
> > in
> > v4 3/3. here is 3/3 updated.
> >
> >
> >
> > arch/arm64/boot/dts/freescale/imx8mq.dtsi | 102
> > ++++++++++++++++++++++
> > 1 file changed, 102 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> > b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> > index 91df9c5350ae..fa83e8294b20 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> > @@ -1099,6 +1099,108 @@ uart4: serial@30a60000 {
> > status = "disabled";
> > };
> >
> > + mipi_csi1: csi@30a70000 {
> > + compatible = "fsl,imx8mq-mipi-
> > csi2";
> > + reg = <0x30a70000 0x1000>;
> > + clocks = <&clk
> > IMX8MQ_CLK_CSI1_CORE>,
> > + <&clk IMX8MQ_CLK_CSI1_ESC>,
> > + <&clk IMX8MQ_CLK_CSI1_PHY_REF>,
> > + <&clk IMX8MQ_CLK_CLKO2>;
> > + clock-names = "core", "esc", "pxl",
> > "clko2";
>
> I can't figure out what the clko2 clock is used for based on the
> datasheet. It seems to be a clock output by the SoC on GPIO1_IO15,
> and
> doesn't seem to belong here.
oh, no it doesn't, I'm sorry, that was just a hack that I forgot about!
That clock is only used by the sensor I'm using -.- I'll remove it
here. thanks a lot for looking closely.
>
> Regarding core, esc and pix, do these clock correspond to the clk,
> clk_esc and clk_ui listed in table 13-36 (section 13.8.3.3.1 "RX
> Local
> Interface Description") of the TRM ? If so, should they be renamed
> accordingly, to either "clk", "clk_esc" and "clk_ui", or, if we want
> to
> drop the prefixes, "core", "esc" and "ui" ?
yes, I think so.
>
> > + assigned-clocks = <&clk
> > IMX8MQ_CLK_CSI1_CORE>,
> > + <&clk IMX8MQ_CLK_CSI1_PHY_REF>,
> > + <&clk IMX8MQ_CLK_CSI1_ESC>;
> > + assigned-clock-rates = <266000000>,
> > <333000000>, <66000000>;
> > + assigned-clock-parents = <&clk
> > IMX8MQ_SYS1_PLL_266M>,
> > + <&clk
> > IMX8MQ_SYS2_PLL_1000M>,
> > + <&clk
> > IMX8MQ_SYS1_PLL_800M>;
> > + power-domains = <&pgc_mipi_csi1>;
> > + resets = <&src>;
>
> The src node has #reset-cells set to 1, I think you're missing
> something
> here.
yes, thank you!
>
> > + fsl,mipi-phy-gpr = <&iomuxc_gpr
> > 0x88>;
> > + interconnects = <&noc
> > IMX8MQ_ICM_CSI1 &noc IMX8MQ_ICS_DRAM>;
> > + interconnect-names = "dram";
> > + status = "disabled";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > +
> > + csi1_mipi_ep:
> > endpoint {
> > + remote-
> > endpoint = <&csi1_ep>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + csi1: csi@30a90000 {
> > + compatible = "fsl,imx8mq-csi",
> > "fsl,imx7-csi";
> > + reg = <0x30a90000 0x10000>;
> > + interrupts = <GIC_SPI 42
> > IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&clk
> > IMX8MQ_CLK_CSI1_ROOT>;
> > + clock-names = "mclk";
> > + status = "disabled";
> > +
> > + port {
> > + csi1_ep: endpoint {
> > + remote-endpoint =
> > <&csi1_mipi_ep>;
> > + };
> > + };
> > + };
> > +
> > + mipi_csi2: csi@30b60000 {
> > + compatible = "fsl,imx8mq-mipi-
> > csi2";
> > + reg = <0x30b60000 0x1000>;
> > + clocks = <&clk
> > IMX8MQ_CLK_CSI2_CORE>,
> > + <&clk IMX8MQ_CLK_CSI2_ESC>,
> > + <&clk IMX8MQ_CLK_CSI2_PHY_REF>,
> > + <&clk IMX8MQ_CLK_CLKO2>;
> > + clock-names = "core", "esc", "pxl",
> > "clko2";
> > + assigned-clocks = <&clk
> > IMX8MQ_CLK_CSI2_CORE>,
> > + <&clk IMX8MQ_CLK_CSI2_PHY_REF>,
> > + <&clk IMX8MQ_CLK_CSI2_ESC>;
> > + assigned-clock-rates = <266000000>,
> > <333000000>, <66000000>;
> > + assigned-clock-parents = <&clk
> > IMX8MQ_SYS1_PLL_266M>,
> > + <&clk
> > IMX8MQ_SYS2_PLL_1000M>,
> > + <&clk
> > IMX8MQ_SYS1_PLL_800M>;
> > + power-domains = <&pgc_mipi_csi2>;
> > + resets = <&src>;
> > + fsl,mipi-phy-gpr = <&iomuxc_gpr
> > 0xa4>;
> > + interconnects = <&noc
> > IMX8MQ_ICM_CSI2 &noc IMX8MQ_ICS_DRAM>;
> > + interconnect-names = "dram";
> > + status = "disabled";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > +
> > + csi2_mipi_ep:
> > endpoint {
> > + remote-
> > endpoint = <&csi2_ep>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + csi2: csi@30b80000 {
> > + compatible = "fsl,imx8mq-csi",
> > "fsl,imx7-csi";
> > + reg = <0x30b80000 0x10000>;
> > + interrupts = <GIC_SPI 43
> > IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&clk
> > IMX8MQ_CLK_CSI2_ROOT>;
> > + clock-names = "mclk";
> > + status = "disabled";
> > +
> > + port {
> > + csi2_ep: endpoint {
> > + remote-endpoint =
> > <&csi2_mipi_ep>;
> > + };
> > + };
> > + };
> > +
> > mu: mailbox@30aa0000 {
> > compatible = "fsl,imx8mq-mu",
> > "fsl,imx6sx-mu";
> > reg = <0x30aa0000 0x10000>;
>
