Hi Martin,
Thank you for the patch.
On Mon, Jun 14, 2021 at 02:25:17PM +0200, Martin Kepplinger wrote:
> Describe the 2 available CSI interfaces on the i.MX8MQ with the MIPI-CSI2
> receiver and the CSI Bridge that provides the user buffers, where the
> existing driver can directly be used.
>
> An image sensor is to be connected to the MIPIs' second port, described in
> board files.
>
> Signed-off-by: Martin Kepplinger <martin.kepplinger@xxxxxxx>
> ---
>
> sorry, the csi compatible addition suggested by Marco was missing in
> v4 3/3. here is 3/3 updated.
>
>
>
> arch/arm64/boot/dts/freescale/imx8mq.dtsi | 102 ++++++++++++++++++++++
> 1 file changed, 102 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> index 91df9c5350ae..fa83e8294b20 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> @@ -1099,6 +1099,108 @@ uart4: serial@30a60000 {
> status = "disabled";
> };
>
> + mipi_csi1: csi@30a70000 {
> + compatible = "fsl,imx8mq-mipi-csi2";
> + reg = <0x30a70000 0x1000>;
> + clocks = <&clk IMX8MQ_CLK_CSI1_CORE>,
> + <&clk IMX8MQ_CLK_CSI1_ESC>,
> + <&clk IMX8MQ_CLK_CSI1_PHY_REF>,
> + <&clk IMX8MQ_CLK_CLKO2>;
> + clock-names = "core", "esc", "pxl", "clko2";
I can't figure out what the clko2 clock is used for based on the
datasheet. It seems to be a clock output by the SoC on GPIO1_IO15, and
doesn't seem to belong here.
Regarding core, esc and pix, do these clock correspond to the clk,
clk_esc and clk_ui listed in table 13-36 (section 13.8.3.3.1 "RX Local
Interface Description") of the TRM ? If so, should they be renamed
accordingly, to either "clk", "clk_esc" and "clk_ui", or, if we want to
drop the prefixes, "core", "esc" and "ui" ?
> + assigned-clocks = <&clk IMX8MQ_CLK_CSI1_CORE>,
> + <&clk IMX8MQ_CLK_CSI1_PHY_REF>,
> + <&clk IMX8MQ_CLK_CSI1_ESC>;
> + assigned-clock-rates = <266000000>, <333000000>, <66000000>;
> + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>,
> + <&clk IMX8MQ_SYS2_PLL_1000M>,
> + <&clk IMX8MQ_SYS1_PLL_800M>;
> + power-domains = <&pgc_mipi_csi1>;
> + resets = <&src>;
The src node has #reset-cells set to 1, I think you're missing something
here.
> + fsl,mipi-phy-gpr = <&iomuxc_gpr 0x88>;
> + interconnects = <&noc IMX8MQ_ICM_CSI1 &noc IMX8MQ_ICS_DRAM>;
> + interconnect-names = "dram";
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + csi1_mipi_ep: endpoint {
> + remote-endpoint = <&csi1_ep>;
> + };
> + };
> + };
> + };
> +
> + csi1: csi@30a90000 {
> + compatible = "fsl,imx8mq-csi", "fsl,imx7-csi";
> + reg = <0x30a90000 0x10000>;
> + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MQ_CLK_CSI1_ROOT>;
> + clock-names = "mclk";
> + status = "disabled";
> +
> + port {
> + csi1_ep: endpoint {
> + remote-endpoint = <&csi1_mipi_ep>;
> + };
> + };
> + };
> +
> + mipi_csi2: csi@30b60000 {
> + compatible = "fsl,imx8mq-mipi-csi2";
> + reg = <0x30b60000 0x1000>;
> + clocks = <&clk IMX8MQ_CLK_CSI2_CORE>,
> + <&clk IMX8MQ_CLK_CSI2_ESC>,
> + <&clk IMX8MQ_CLK_CSI2_PHY_REF>,
> + <&clk IMX8MQ_CLK_CLKO2>;
> + clock-names = "core", "esc", "pxl", "clko2";
> + assigned-clocks = <&clk IMX8MQ_CLK_CSI2_CORE>,
> + <&clk IMX8MQ_CLK_CSI2_PHY_REF>,
> + <&clk IMX8MQ_CLK_CSI2_ESC>;
> + assigned-clock-rates = <266000000>, <333000000>, <66000000>;
> + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>,
> + <&clk IMX8MQ_SYS2_PLL_1000M>,
> + <&clk IMX8MQ_SYS1_PLL_800M>;
> + power-domains = <&pgc_mipi_csi2>;
> + resets = <&src>;
> + fsl,mipi-phy-gpr = <&iomuxc_gpr 0xa4>;
> + interconnects = <&noc IMX8MQ_ICM_CSI2 &noc IMX8MQ_ICS_DRAM>;
> + interconnect-names = "dram";
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + csi2_mipi_ep: endpoint {
> + remote-endpoint = <&csi2_ep>;
> + };
> + };
> + };
> + };
> +
> + csi2: csi@30b80000 {
> + compatible = "fsl,imx8mq-csi", "fsl,imx7-csi";
> + reg = <0x30b80000 0x10000>;
> + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MQ_CLK_CSI2_ROOT>;
> + clock-names = "mclk";
> + status = "disabled";
> +
> + port {
> + csi2_ep: endpoint {
> + remote-endpoint = <&csi2_mipi_ep>;
> + };
> + };
> + };
> +
> mu: mailbox@30aa0000 {
> compatible = "fsl,imx8mq-mu", "fsl,imx6sx-mu";
> reg = <0x30aa0000 0x10000>;
--
Regards,
Laurent Pinchart
