[PATCH 11/14] ARM: dts: suniv: F1C100: add SPI support

[Andre Przywara <andre.przywara@xxxxxxx>]

The F1C100 series contains two SPI controllers, and many boards use SPI0
for a SPI flash, as the BROM is able to boot from that.

Describe the two controllers in the SoC .dtsi, and also add the PortC
pins for SPI0, since this is where BROM looks at when trying to boot
from the commonly used SPI flash.

The SPI controller seems to be the same as in the H3 chips, but it lacks
a separate mod clock. The manual says it's connected to AHB directly.
We don't export that AHB clock directly, but can use the AHB *gate* clock
as a clock source, since the MMC driver is not supposed to change the AHB
frequency anyway.

Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
---
 arch/arm/boot/dts/suniv-f1c100s.dtsi | 33 ++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/arch/arm/boot/dts/suniv-f1c100s.dtsi b/arch/arm/boot/dts/suniv-f1c100s.dtsi
index 6f2f97458fe0..f8ec1c7a2ca9 100644
--- a/arch/arm/boot/dts/suniv-f1c100s.dtsi
+++ b/arch/arm/boot/dts/suniv-f1c100s.dtsi
@@ -105,6 +105,34 @@ mmc1: mmc@1c10000 {
 			#size-cells = <0>;
 		};
 
+		spi0: spi@1c05000 {
+			compatible = "allwinner,suniv-f1c100s-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c05000 0x1000>;
+			interrupts = <10>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_BUS_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			status = "disabled";
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@1c06000 {
+			compatible = "allwinner,suniv-f1c100s-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c06000 0x1000>;
+			interrupts = <11>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_BUS_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			status = "disabled";
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		ccu: clock@1c20000 {
 			compatible = "allwinner,suniv-f1c100s-ccu";
 			reg = <0x01c20000 0x400>;
@@ -138,6 +166,11 @@ mmc0_pins: mmc0-pins {
 				drive-strength = <30>;
 			};
 
+			spi0_pc_pins: spi0-pc-pins {
+				pins = "PC0", "PC1", "PC2", "PC3";
+				function = "spi0";
+			};
+
 			uart0_pe_pins: uart0-pe-pins {
 				pins = "PE0", "PE1";
 				function = "uart0";
-- 
2.25.1