Re: [PATCH 1/4] firmware: xilinx: Add OSPI Mux selection support

[Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>]

On Fri, Sep 24, 2021 at 02:12:55PM +0200, Michal Simek wrote:
> 
> 
> On 9/24/21 1:36 PM, Greg Kroah-Hartman wrote:
> > On Fri, Sep 24, 2021 at 03:37:08PM +0530, Sai Krishna Potthuri wrote:
> >> Add OSPI Mux selection API support to select the AXI interface to OSPI.
> >>
> >> Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xxxxxxxxxx>
> >> ---
> >>  drivers/firmware/xilinx/zynqmp.c     | 17 +++++++++++++++++
> >>  include/linux/firmware/xlnx-zynqmp.h | 12 ++++++++++++
> >>  2 files changed, 29 insertions(+)
> >>
> >> diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c
> >> index 15b138326ecc..43c3b5a9eef7 100644
> >> --- a/drivers/firmware/xilinx/zynqmp.c
> >> +++ b/drivers/firmware/xilinx/zynqmp.c
> >> @@ -647,6 +647,23 @@ int zynqmp_pm_sd_dll_reset(u32 node_id, u32 type)
> >>  }
> >>  EXPORT_SYMBOL_GPL(zynqmp_pm_sd_dll_reset);
> >>  
> >> +/**
> >> + * zynqmp_pm_ospi_mux_select() - OSPI Mux selection
> >> + *
> >> + * @dev_id:	Device Id of the OSPI device.
> >> + * @select:	OSPI Mux select value.
> >> + *
> >> + * This function select the OSPI Mux.
> >> + *
> >> + * Return:	Returns status, either success or error+reason
> >> + */
> >> +int zynqmp_pm_ospi_mux_select(u32 dev_id, u32 select)
> >> +{
> >> +	return zynqmp_pm_invoke_fn(PM_IOCTL, dev_id, IOCTL_OSPI_MUX_SELECT,
> >> +				   select, 0, NULL);
> >> +}
> >> +EXPORT_SYMBOL_GPL(zynqmp_pm_ospi_mux_select);
> >> +
> >>  /**
> >>   * zynqmp_pm_write_ggs() - PM API for writing global general storage (ggs)
> >>   * @index:	GGS register index
> >> diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h
> >> index 9d1a5c175065..6979a79f553a 100644
> >> --- a/include/linux/firmware/xlnx-zynqmp.h
> >> +++ b/include/linux/firmware/xlnx-zynqmp.h
> >> @@ -119,6 +119,7 @@ enum pm_ioctl_id {
> >>  	IOCTL_READ_PGGS = 15,
> >>  	/* Set healthy bit value */
> >>  	IOCTL_SET_BOOT_HEALTH_STATUS = 17,
> >> +	IOCTL_OSPI_MUX_SELECT = 21,
> > 
> > Why the gap?  What are the commands in the middle for?
> 
> Below is the full list. Not everything has been upstream yet. There was
> an attempt on AFI which one colleague is working on and should send new
> version soon. I don't think anybody has started with upstreaming probe
> counters.
> Every part has different owner with unfortunately own upstreaming plan.
> 
> Thanks,
> Michal
> 
> enum pm_ioctl_id {
> 	IOCTL_GET_RPU_OPER_MODE = 0,
> 	IOCTL_SET_RPU_OPER_MODE = 1,
> 	IOCTL_RPU_BOOT_ADDR_CONFIG = 2,
> 	IOCTL_TCM_COMB_CONFIG = 3,
> 	IOCTL_SET_TAPDELAY_BYPASS = 4,
> 	IOCTL_SET_SGMII_MODE = 5,
> 	IOCTL_SD_DLL_RESET = 6,
> 	IOCTL_SET_SD_TAPDELAY = 7,
> 	IOCTL_SET_PLL_FRAC_MODE = 8,
> 	IOCTL_GET_PLL_FRAC_MODE = 9,
> 	IOCTL_SET_PLL_FRAC_DATA = 10,
> 	IOCTL_GET_PLL_FRAC_DATA = 11,
> 	IOCTL_WRITE_GGS = 12,
> 	IOCTL_READ_GGS = 13,
> 	IOCTL_WRITE_PGGS = 14,
> 	IOCTL_READ_PGGS = 15,
> 	/* IOCTL for ULPI reset */
> 	IOCTL_ULPI_RESET = 16,
> 	/* Set healthy bit value */
> 	IOCTL_SET_BOOT_HEALTH_STATUS = 17,
> 	IOCTL_AFI = 18,
> 	/* Probe counter read/write */
> 	IOCTL_PROBE_COUNTER_READ = 19,
> 	IOCTL_PROBE_COUNTER_WRITE = 20,
> 	IOCTL_OSPI_MUX_SELECT = 21,
> 	/* IOCTL for USB power request */
> 	IOCTL_USB_SET_STATE = 22,
> 	/* IOCTL to get last reset reason */
> 	IOCTL_GET_LAST_RESET_REASON = 23,
> 	/* AI engine NPI ISR clear */
> 	IOCTL_AIE_ISR_CLEAR = 24,
> 	/* Register SGI to ATF */
> 	IOCTL_REGISTER_SGI = 25,
> 	/* Runtime feature configuration */
> 	IOCTL_SET_FEATURE_CONFIG = 26,
> 	IOCTL_GET_FEATURE_CONFIG = 27,
> };

Odd mix of comments and no comments...

Anyway, that's fine, just curious as to why there was a gap.  No real
reason why you can't just add them all now right?

thanks,

greg k-h