Hi Miquèl,
On 20/08/21 5:48 pm, Miquel Raynal wrote:
Hi Apurva,
Apurva Nandan <a-nandan@xxxxxx> wrote on Fri, 20 Aug 2021 17:09:07
+0530:
Hi Miquèl,
On 07/08/21 12:38 am, Miquel Raynal wrote:
Hi Apurva,
Apurva Nandan <a-nandan@xxxxxx> wrote on Tue, 13 Jul 2021 13:05:36
+0000:
Manufacturers like Gigadevice and Winbond are adding Power-on-Reset
functionality in their SPI NAND flash chips. PoR instruction consists
of a 66h command followed by 99h command, and is different from the FFh
reset. The reset command FFh just clears the status only registers,
while the PoR command erases all the configurations written to the
flash and is equivalent to a power-down -> power-up cycle.
Add support for the Power-on-Reset command for any flash that provides
this feature.
Datasheet: https://www.winbond.com/export/sites/winbond/datasheet/W35N01JW_Datasheet_Brief.pdf
Signed-off-by: Apurva Nandan <a-nandan@xxxxxx>
---
[...]
\
@@ -218,6 +230,8 @@ struct spinand_device;
* reading/programming/erasing when the RESET occurs. Since we always
* issue a RESET when the device is IDLE, 5us is selected for both initial
* and poll delay.
+ * Power on Reset can take max upto 500 us to complete, so sleep for 1000 us
s/max upto/up to/
Okay!
+ * to 1200 us safely.
I don't really get why, if the maximum is 500, then let's wait for
500us.
Generally we keep some margin from the maximum time, no?
Well, yes and no.
If you know that an operation will last Xms and have nothing else to
do, then you can take some margin if you are in a probe (called once)
but definitely not if you are in a fast path.
I think as PoR reset would be called at every mtd_suspend() call, so we
can reduce the delay. And we would be expecting some time gap before the
next mtd_resume() call.
Otherwise the best is to have some kind of signaling but I'm not sure
you'll have one for the reset op...
According to public datasheet, it doesn't set the busy bit during reset.
So do you suggest in the favor of removing the delay margin?
*/
#define SPINAND_READ_INITIAL_DELAY_US 6
#define SPINAND_READ_POLL_DELAY_US 5
@@ -227,6 +241,8 @@ struct spinand_device;
#define SPINAND_WRITE_POLL_DELAY_US 15
#define SPINAND_ERASE_INITIAL_DELAY_US 250
#define SPINAND_ERASE_POLL_DELAY_US 50
+#define SPINAND_POR_MIN_DELAY_US 1000
+#define SPINAND_POR_MAX_DELAY_US 1200
>> #define SPINAND_WAITRDY_TIMEOUT_MS 400
>> @@ -351,6 +367,7 @@ struct spinand_ecc_info {
#define SPINAND_HAS_QE_BIT BIT(0)
#define SPINAND_HAS_CR_FEAT_BIT BIT(1)
#define SPINAND_HAS_OCTAL_DTR_BIT BIT(2)
+#define SPINAND_HAS_POR_CMD_BIT BIT(3)
>> /**
* struct spinand_ondie_ecc_conf - private SPI-NAND on-die ECC engine structure
Thanks,
Miquèl
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Thanks,
Apurva Nandan
Thanks,
Miquèl
Thanks,
Apurva Nandan