On Octal DTR capable flashes like Micron Xcella reads cannot start or end at an odd address in Octal DTR mode. Extra bytes need to be read at the start or end to make sure both the start address and length remain even. To avoid allocating too much extra memory, thereby putting unnecessary memory pressure on the system, the temporary buffer containing the extra padding bytes is capped at PAGE_SIZE bytes. The rest of the 2-byte aligned part should be read directly in the main buffer. Signed-off-by: Pratyush Yadav <p.yadav@xxxxxx> --- drivers/mtd/spi-nor/core.c | 81 +++++++++++++++++++++++++++++++++++++- 1 file changed, 80 insertions(+), 1 deletion(-) diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c index 5cc206b8bbf3..3d66cc34af4d 100644 --- a/drivers/mtd/spi-nor/core.c +++ b/drivers/mtd/spi-nor/core.c @@ -1904,6 +1904,82 @@ static const struct flash_info *spi_nor_read_id(struct spi_nor *nor) return ERR_PTR(-ENODEV); } +/* + * On Octal DTR capable flashes like Micron Xcella reads cannot start or + * end at an odd address in Octal DTR mode. Extra bytes need to be read + * at the start or end to make sure both the start address and length + * remain even. + */ +static int spi_nor_octal_dtr_read(struct spi_nor *nor, loff_t from, size_t len, + u_char *buf) +{ + u_char *tmp_buf; + size_t tmp_len; + loff_t start, end; + int ret, bytes_read; + + if (IS_ALIGNED(from, 2) && IS_ALIGNED(len, 2)) + return spi_nor_read_data(nor, from, len, buf); + else if (IS_ALIGNED(from, 2) && len > PAGE_SIZE) + return spi_nor_read_data(nor, from, round_down(len, PAGE_SIZE), + buf); + + tmp_buf = kmalloc(PAGE_SIZE, GFP_KERNEL); + if (!tmp_buf) + return -ENOMEM; + + start = round_down(from, 2); + end = round_up(from + len, 2); + + /* + * Avoid allocating too much memory. The requested read length might be + * quite large. Allocating a buffer just as large (slightly bigger, in + * fact) would put unnecessary memory pressure on the system. + * + * For example if the read is from 3 to 1M, then this will read from 2 + * to 4098. The reads from 4098 to 1M will then not need a temporary + * buffer so they can proceed as normal. + */ + tmp_len = min_t(size_t, end - start, PAGE_SIZE); + + ret = spi_nor_read_data(nor, start, tmp_len, tmp_buf); + if (ret == 0) { + ret = -EIO; + goto out; + } + if (ret < 0) + goto out; + + /* + * More bytes are read than actually requested, but that number can't be + * reported to the calling function or it will confuse its calculations. + * Calculate how many of the _requested_ bytes were read. + */ + bytes_read = ret; + + if (from != start) + ret -= from - start; + + /* + * Only account for extra bytes at the end if they were actually read. + * For example, if the total length was truncated because of temporary + * buffer size limit then the adjustment for the extra bytes at the end + * is not needed. + */ + if (start + bytes_read == end) + ret -= end - (from + len); + + if (ret < 0) { + ret = -EIO; + goto out; + } + + memcpy(buf, tmp_buf + (from - start), ret); +out: + kfree(tmp_buf); + return ret; +} + static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf) { @@ -1921,7 +1997,10 @@ static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len, addr = spi_nor_convert_addr(nor, addr); - ret = spi_nor_read_data(nor, addr, len, buf); + if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) + ret = spi_nor_octal_dtr_read(nor, addr, len, buf); + else + ret = spi_nor_read_data(nor, addr, len, buf); if (ret == 0) { /* We shouldn't see 0-length reads */ ret = -EIO; -- 2.30.0