Re: [RFC PATCH 1/6] spi: spi-mem: Tell controller when device is ready for calibration

[Pratyush Yadav <p.yadav@xxxxxx>]

On 24/03/21 12:07AM, Michael Walle wrote:
> Hi Pratyush,
> 
> Am 2021-03-11 20:12, schrieb Pratyush Yadav:
> > Some controllers like the Cadence OSPI controller need to perform a
> > calibration sequence to operate at high clock speeds. This calibration
> > should happen after the flash is fully initialized otherwise the
> > calibration might happen in a different SPI mode from the one the flash
> > is finally set to. Add a hook that can be used to tell the controller
> > when the flash is ready for calibration. Whether calibration is needed
> > depends on the controller.
> > 
> > Signed-off-by: Pratyush Yadav <p.yadav@xxxxxx>
> > ---
> >  drivers/spi/spi-mem.c       | 12 ++++++++++++
> >  include/linux/spi/spi-mem.h |  8 ++++++++
> >  2 files changed, 20 insertions(+)
> > 
> > diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
> > index dc713b0c3c4d..e2f05ad3f4dc 100644
> > --- a/drivers/spi/spi-mem.c
> > +++ b/drivers/spi/spi-mem.c
> > @@ -464,6 +464,18 @@ int spi_mem_adjust_op_size(struct spi_mem *mem,
> > struct spi_mem_op *op)
> >  }
> >  EXPORT_SYMBOL_GPL(spi_mem_adjust_op_size);
> > 
> > +int spi_mem_do_calibration(struct spi_mem *mem, struct spi_mem_op *op)
> > +{
> > +	struct spi_controller *ctlr = mem->spi->controller;
> > +
> > +	if (!ctlr->mem_ops || !ctlr->mem_ops->do_calibration)
> > +		return -EOPNOTSUPP;
> > +
> > +	ctlr->mem_ops->do_calibration(mem, op);
> 
> Can't a calibration fail?

It can. If it does, the controller falls back to lower speed transfers. 
There is not much the upper layer can do about this. That's why it is 
not informed whether it succeeded or not.

> 
> > +	return 0;
> > +}
> > +EXPORT_SYMBOL_GPL(spi_mem_do_calibration);
> > +
> >  static ssize_t spi_mem_no_dirmap_read(struct spi_mem_dirmap_desc *desc,
> >  				      u64 offs, size_t len, void *buf)
> >  {
> > diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
> > index 2b65c9edc34e..97a2d280f2d0 100644
> > --- a/include/linux/spi/spi-mem.h
> > +++ b/include/linux/spi/spi-mem.h
> > @@ -250,6 +250,12 @@ static inline void *spi_mem_get_drvdata(struct
> > spi_mem *mem)
> >   *		  the currently mapped area), and the caller of
> >   *		  spi_mem_dirmap_write() is responsible for calling it again in
> >   *		  this case.
> > + * @do_calibration: perform calibration needed for high SPI clock speed
> > + *		    operation. Should be called after the SPI memory device has
> > + *		    been completely initialized. The op passed should contain
> > + *		    a template for the read operation used for the device so
> > + *		    the controller can decide what type of calibration is
> > + *		    required for this type of read.
> >   *
> >   * This interface should be implemented by SPI controllers providing an
> >   * high-level interface to execute SPI memory operation, which is
> > usually the
> > @@ -274,6 +280,7 @@ struct spi_controller_mem_ops {
> >  			       u64 offs, size_t len, void *buf);
> >  	ssize_t (*dirmap_write)(struct spi_mem_dirmap_desc *desc,
> >  				u64 offs, size_t len, const void *buf);
> > +	void (*do_calibration)(struct spi_mem *mem, struct spi_mem_op *op);
> >  };
> > 
> >  /**
> > @@ -346,6 +353,7 @@ bool spi_mem_dtr_supports_op(struct spi_mem *mem,
> >  #endif /* CONFIG_SPI_MEM */
> > 
> >  int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op);
> > +int spi_mem_do_calibration(struct spi_mem *mem, struct spi_mem_op *op);
> > 
> >  bool spi_mem_supports_op(struct spi_mem *mem,
> >  			 const struct spi_mem_op *op);
> 
> -- 
> -michael

-- 
Regards,
Pratyush Yadav
Texas Instruments Inc.