> -----Original Message-----
> From: Ashish Kumar <ashish.kumar@xxxxxxx>
> Sent: Wednesday, September 9, 2020 4:57 PM
> To: kuldip dwivedi <kuldip.dwivedi@xxxxxxxxxxxxxxxx>; Yogesh Gaur
> <yogeshgaur.83@xxxxxxxxx>; Mark Brown <broonie@xxxxxxxxxx>; linux-
> spi@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx
> Cc: Varun Sethi <V.Sethi@xxxxxxx>; Arokia Samy <arokia.samy@xxxxxxx>
> Subject: RE: [EXT] [PATCH v1] spi: spi-nxp-fspi: Add ACPI support
>
> Hi Kuldeep Dwivedi,
Don't mind but It's Kuldip not Kuldeep
>
> > -----Original Message-----
> > From: kuldip dwivedi <kuldip.dwivedi@xxxxxxxxxxxxxxxx>
> > Sent: Tuesday, September 8, 2020 11:32 AM
> > To: Ashish Kumar <ashish.kumar@xxxxxxx>; Yogesh Gaur
> > <yogeshgaur.83@xxxxxxxxx>; Mark Brown <broonie@xxxxxxxxxx>; linux-
> > spi@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx
> > Cc: Varun Sethi <V.Sethi@xxxxxxx>; Arokia Samy <arokia.samy@xxxxxxx>;
> > kuldip dwivedi <kuldip.dwivedi@xxxxxxxxxxxxxxxx>
> > Subject: [EXT] [PATCH v1] spi: spi-nxp-fspi: Add ACPI support
> >
> > Caution: EXT Email
> >
> > Currently NXP fspi driver has support of DT only. Adding ACPI support
> > to the driver so that it can be used by UEFI firmware booting in ACPI
> > mode. This driver will be probed if any firmware will expose HID
> > "NXP0009" in DSDT table.
> >
> > Signed-off-by: kuldip dwivedi <kuldip.dwivedi@xxxxxxxxxxxxxxxx>
> Does these change affects non-ACPI FSPI driver in Linux? What test case
were run
> to verify the same?
I have verified on both DT and ACPI mode with below method. In this method
we
Used mtd utility to write some content and then read from same address.
Address 0x3000000 has been selected to avoid any data loss of existing
UEFI variables.
root@localhost:/mnt# ls
1.c EFI i2c_utils mtd_debug mtdinfo reportfreq64
root@localhost:/mnt# cat 1.c
1234567890987654321
root@localhost:/mnt#
root@localhost:/mnt# ./mtdinfo
Count of MTD devices: 2
Present MTD devices: mtd0, mtd1
Sysfs interface supported: yes
root@localhost:/mnt# ./mtd_debug erase /dev/mtd1 0x3000000 0x1000
Erased 4096 bytes from address 0x03000000 in flash
root@localhost:/mnt# ./mtd_debug write /dev/mtd1 0x3000000 20 1.c
Copied 20 bytes from 1.c to address 0x03000000 in flash
root@lOcalhost:/mnt# ./mtd_debug read /dev/mtd1 0x3000000 20 2.c
Copied 20 bytes from address 0x03000000 in flash tO 2.c
root@localhost:/mnt# cat 2.c
1234567890987654321
> > ---
> >
> > Notes:
> > 1. Add ACPI match table
> > 2. Change the DT specific APIs to device property APIs
> > so that same API can be used in DT and ACPi mode.
> > 3. Omit clock configuration part - in ACPI world, the firmware
> > is responsible for clock maintenance.
> > 4. This patch is tested on LX2160A platform
> >
> > drivers/spi/spi-nxp-fspi.c | 66
> > +++++++++++++++++++++++++++-----------
> > 1 file changed, 47 insertions(+), 19 deletions(-)
> >
> > diff --git a/drivers/spi/spi-nxp-fspi.c b/drivers/spi/spi-nxp-fspi.c
> > index 1ccda82da206..acdb186ddfb2 100644
> > --- a/drivers/spi/spi-nxp-fspi.c
> > +++ b/drivers/spi/spi-nxp-fspi.c
> > @@ -3,7 +3,8 @@
> > /*
> > * NXP FlexSPI(FSPI) controller driver.
> > *
> > - * Copyright 2019 NXP.
> > + * Copyright 2019-2020 NXP
> Why Update NXP copyright?
This is asked by NXP only
>
> > + * Copyright 2020 Puresoftware Ltd.
> > *
> > * FlexSPI is a flexsible SPI host controller which supports two SPI
> > * channels and up to 4 external devices. Each channel supports @@
> > -30,6 +31,7 @@
> > * Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>
> > */
> >
> > +#include <linux/acpi.h>
> > #include <linux/bitops.h>
> > #include <linux/clk.h>
> > #include <linux/completion.h>
> > @@ -563,6 +565,9 @@ static int nxp_fspi_clk_prep_enable(struct
> > nxp_fspi
> > *f)
> > {
> > int ret;
> >
> > + if (is_acpi_node(f->dev->fwnode))
> > + return 0;
> > +
> > ret = clk_prepare_enable(f->clk_en);
> > if (ret)
> > return ret;
> > @@ -576,10 +581,15 @@ static int nxp_fspi_clk_prep_enable(struct
> > nxp_fspi *f)
> > return 0;
> > }
> >
> > -static void nxp_fspi_clk_disable_unprep(struct nxp_fspi *f)
> > +static int nxp_fspi_clk_disable_unprep(struct nxp_fspi *f)
> > {
> > + if (is_acpi_node(f->dev->fwnode))
> > + return 0;
> > +
> > clk_disable_unprepare(f->clk);
> > clk_disable_unprepare(f->clk_en);
> > +
> > + return 0;
> > }
> >
> > /*
> > @@ -900,6 +910,8 @@ static int nxp_fspi_default_setup(struct nxp_fspi
*f)
> > return ret;
> >
> > /* Reset the module */
> > + fspi_writel(f, FSPI_MCR0_SWRST, (base + FSPI_MCR0));
> > +
> Why is this SW reset needed now? This will alter nxp_fspi_resume()
function as
> well.
I observed a kernel panic during setting up the driver in
nxp_fspi_default_setup function in ACPI boot and this is fixed.
>
> > /* w1c register, wait unit clear */
> > ret = fspi_readl_poll_tout(f, f->iobase + FSPI_MCR0,
> > FSPI_MCR0_SWRST, 0, POLL_TOUT,
> > false); @@ -1001,7 +1013,7 @@ static int nxp_fspi_probe(struct
> > platform_device
> > *pdev)
> >
> > f = spi_controller_get_devdata(ctlr);
> > f->dev = dev;
> > - f->devtype_data = of_device_get_match_data(dev);
> > + f->devtype_data = device_get_match_data(dev);
> > if (!f->devtype_data) {
> > ret = -ENODEV;
> > goto err_put_ctrl;
> > @@ -1011,6 +1023,8 @@ static int nxp_fspi_probe(struct platform_device
> > *pdev)
> >
> > /* find the resources - configuration register address space
*/
> > res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> > "fspi_base");
> > + if (!res)
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> Why is this needed ?, _byname() will get you fspi_base value.
In ACPI we can not pass resource value by name where as we have to pass
By index. So in 0th Index there is FSPI_BASE and in 1st index FSPIMM_BASE.
For reference Please see , Line :23 and Line:24
https://source.codeaurora.org/external/qoriq/qoriq-components/edk2-platfor
ms/tree/Platform/NXP/LX2160aRdbPkg/AcpiTables/Dsdt/FSPI.asl?h=LX2160_UEFI_
ACPI_EAR3
>
> > f->iobase = devm_ioremap_resource(dev, res);
> > if (IS_ERR(f->iobase)) {
> > ret = PTR_ERR(f->iobase); @@ -1020,8 +1034,11 @@
> > static int nxp_fspi_probe(struct platform_device
> > *pdev)
> > /* find the resources - controller memory mapped space */
> > res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> > "fspi_mmap");
> > if (!res) {
> > - ret = -ENODEV;
> > - goto err_put_ctrl;
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> Why is this needed? _byname() will get you fspi_mmap.
> If fspi_mmap is not present then fetch 1st IORESOURE_MEM ?
In ACPI we can not pass resource value by name where as we have to pass
By index. So in 0th Index there is FSPI_BASE and in 1st index FSPIMM_BASE.
For reference Please see , Line :23 and Line:24
https://source.codeaurora.org/external/qoriq/qoriq-components/edk2-platfor
ms/tree/Platform/NXP/LX2160aRdbPkg/AcpiTables/Dsdt/FSPI.asl?h=LX2160_UEFI_
ACPI_EAR3
>
> Regards
> Ashish
> > + if (!res) {
> > + ret = -ENODEV;
> > + goto err_put_ctrl;
> > + }
> > }
> >
> > /* assign memory mapped starting address and mapped size. */
> > @@ -1029,22 +1046,24 @@ static int nxp_fspi_probe(struct
> > platform_device
> > *pdev)
> > f->memmap_phy_size = resource_size(res);
> >
> > /* find the clocks */
> > - f->clk_en = devm_clk_get(dev, "fspi_en");
> > - if (IS_ERR(f->clk_en)) {
> > - ret = PTR_ERR(f->clk_en);
> > - goto err_put_ctrl;
> > - }
> > + if (dev_of_node(&pdev->dev)) {
> > + f->clk_en = devm_clk_get(dev, "fspi_en");
> > + if (IS_ERR(f->clk_en)) {
> > + ret = PTR_ERR(f->clk_en);
> > + goto err_put_ctrl;
> > + }
> >
> > - f->clk = devm_clk_get(dev, "fspi");
> > - if (IS_ERR(f->clk)) {
> > - ret = PTR_ERR(f->clk);
> > - goto err_put_ctrl;
> > - }
> > + f->clk = devm_clk_get(dev, "fspi");
> > + if (IS_ERR(f->clk)) {
> > + ret = PTR_ERR(f->clk);
> > + goto err_put_ctrl;
> > + }
> >
> > - ret = nxp_fspi_clk_prep_enable(f);
> > - if (ret) {
> > - dev_err(dev, "can not enable the clock\n");
> > - goto err_put_ctrl;
> > + ret = nxp_fspi_clk_prep_enable(f);
> > + if (ret) {
> > + dev_err(dev, "can not enable the clock\n");
> > + goto err_put_ctrl;
> > + }
> > }
> >
> > /* find the irq */
> > @@ -1127,6 +1146,14 @@ static const struct of_device_id
> > nxp_fspi_dt_ids[] = { }; MODULE_DEVICE_TABLE(of, nxp_fspi_dt_ids);
> >
> > +#ifdef CONFIG_ACPI
> > +static const struct acpi_device_id nxp_fspi_acpi_ids[] = {
> > + { "NXP0009", .driver_data = (kernel_ulong_t)&lx2160a_data, },
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(acpi, nxp_fspi_acpi_ids); #endif
> > +
> > static const struct dev_pm_ops nxp_fspi_pm_ops = {
> > .suspend = nxp_fspi_suspend,
> > .resume = nxp_fspi_resume,
> > @@ -1136,6 +1163,7 @@ static struct platform_driver nxp_fspi_driver =
{
> > .driver = {
> > .name = "nxp-fspi",
> > .of_match_table = nxp_fspi_dt_ids,
> > + .acpi_match_table = ACPI_PTR(nxp_fspi_acpi_ids),
> > .pm = &nxp_fspi_pm_ops,
> > },
> > .probe = nxp_fspi_probe,
> > --
> > 2.17.1
Thanks,
RE: [EXT] [PATCH v1] spi: spi-nxp-fspi: Add ACPI support
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: RE: [EXT] [PATCH v1] spi: spi-nxp-fspi: Add ACPI support
- From: Kuldip Dwivedi <kuldip.dwivedi@xxxxxxxxxxxxxxxx>
- Date: Wed, 9 Sep 2020 19:47:04 +0530
- Cc: Varun Sethi <V.Sethi@xxxxxxx>, Arokia Samy <arokia.samy@xxxxxxx>
- In-reply-to: <HE1PR04MB3196017359FD8B44F44EE5EC95260@HE1PR04MB3196.eurprd04.prod.outlook.com>
- References: <20200908060227.299-1-kuldip.dwivedi@puresoftware.com> <HE1PR04MB3196017359FD8B44F44EE5EC95260@HE1PR04MB3196.eurprd04.prod.outlook.com>
- References:
- [PATCH v1] spi: spi-nxp-fspi: Add ACPI support
- From: kuldip dwivedi
- RE: [EXT] [PATCH v1] spi: spi-nxp-fspi: Add ACPI support
- From: Ashish Kumar
- [PATCH v1] spi: spi-nxp-fspi: Add ACPI support
- Prev by Date: Patchwork summary for: spi-devel-general
- Next by Date: Re: [PATCH V2 0/8] opp: Unconditionally call dev_pm_opp_of_remove_table()
- Previous by thread: RE: [EXT] [PATCH v1] spi: spi-nxp-fspi: Add ACPI support
- Next by thread: Re: [PATCH v1] spi: spi-nxp-fspi: Add ACPI support
- Index(es):
 |