Re: [PATCH v4 4/5] ARM: dts: DRA7: add entry for qspi mmap region

[Vignesh R <vigneshr@xxxxxx>]

On 12/01/2015 10:09 PM, Tony Lindgren wrote:
> * Vignesh R <vigneshr@xxxxxx> [151130 20:46]:
>> On 12/01/2015 04:04 AM, Tony Lindgren wrote:
>>>
>>> Actually none of the IO areas above are within the same interconnect target:
>>>
>>> 0x4b300000  QSPI0 address space in L3 main interconnect
>>> 0x5c000000  QSPI1 address space in L3 main interconnect
>>
>>
>> First address range (configuration port: 0x4b300000) corresponds to QSPI
>> registers space. These registers alone are sufficient for generic SPI
>> communication (serial flash as well as non-flash SPI devices).
> 
> OK
> 
>> In order to speed up SPI flash reads SFI_MM_IF(SPI memory mapped
>> interface) is provided by QSPI IP. This _cannot_ be used with non-flash
>> devices.
> 
> OK
> 
>> The second address range (0x5c000000) corresponds to memory-mapped
>> region of SFI_MM_IF, through which SPI flash memories can be read as if
>> though they were RAM addresses (i.e using readl/memcpy). The SFI_MM_IF
>> block that takes care of communicating over SPI bus and getting the data
>> from flash device.
> 
> OK
> 
>> But SFI_MM_IF block needs to know some flash specific information(such
>> as read opcode, address bytes, dummy bytes, mode). This information must
>> first be populated in QSPI_SPI_SETUP*_REG(0x4B300054-60) before
>> accessing SFI_MM_IF address range via readl.
>> Both addresses space belong to same instance of the driver, one
>> corresponds to register space and other is memory-mapped region.
>> Therefore both regions are claimed by the same driver.
> 
> OK
> 
>>> 0x4a002558  CTRL_CORE_CONTROL_IO_2 in System Control Module (SCM) in L4_CFG
>>>
>>> The first two address spaces should be two separate instances of this driver.
>>
>> Not actually two instances.
> 
> OK. They are both on L3 main so that won't cause any issues for separate
> interconnect driver instances. As they are still separate targets flushing
> a posted write to one area will not flush anything to the other.
> 

I didn't quite understand what you meant by interconnect driver instance.
qspi_base and qspi_mmap region are tightly bound to each other and both
needs to be accessed by ti-qspi driver (though different targets).
Besides qspi_mmap region is only used to read data, there will not be
any write accesses to this target. Are you saying this binding is not
viable?

>>> The CTRL_CORE_CONTROL_IO_2 needs seems like a shared clock register that
>>> needs to be accessed using the clock framework most likely.
>>>
>>
>> Not shared clock.
>> The CTRL_CORE_CONTROL_IO_2[10:8] QSPI_MEMMAPPED_CS bit fields provides a
>> functionality for remapping the previously described address space which
>> starts at 0x5C000000 L3_MAIN address to one of the four supported chip
>> selects.
>> How about using syscon to access CTRL_CORE_CONTROL_IO_2?
> 
> A separate driver implementing some Linux generic framework would be idael :)
> 
> But if that does not fit, yeah then syscon makes sense as that IO range
> will be on separate interconnect driver (and clock and possibly power domain)
> instances eventually.
> 

I will go ahead with syscon for accessing CTRL_CORE_CONTROL_IO_2 register.

-- 
Regards
Vignesh
--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html