Re: [PATCH 2/2] dt/bindings: control CS via standard GPIO operations instead of SPI-HW

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



> On 07.03.2015, at 06:47, Stephen Warren <swarren@xxxxxxxxxxxxx> wrote:
> 
> These pins aren't used by anything on the board, but are rather part of
> the expansion header. I wonder if we wouldn't be better off removing any
> configuration of the pins from the DT. After all, we can't guarantee how
> the user has connected them. The "default" usage, a/k/a the expansion
> header signal naming, isn't any guarantee.
> 
> Rather, the user should specify what they want to use the pin as; as a
> GPIO input, GPIO output, or an SPI chip-select.
...
> While the existing DT already has this issue, note that this forces
> these pins to be driven as outputs. What if the user has hooked up an
> external device that drives these signals, and wants to use the pins as
> GPIO inputs?


Actually if you look at the Documentation on page 102 you will find that
those pins are pulled high by default (if it is HW or firmware I am not
sure) - so a hat designer needs to take this into consideration anyway.
The only difference is that it is pulled high and not driven high/low.

Also with the "new" models there is the Firmware that will read those 
"hat-descriptors" from the eeprom and configure the GPIO "modes" and
pullups based on this information.

But then it means in principle that this is a more general issue
that just became apparent now.


> This shouldn't be in the SoC .dtsi file. It's quite possible for someone
> to use other GPIOs as SPI CS. It's board or even use-case specific
> whether those are the correct values.
> 
> I would argue that we should not put any cs-gpios into any in-kernel DT
> file, since there's no on-board usage of SPI on the RPi boards.

but then: why not just make it optional and NOT configuring it at all
and keep it "outside".

> For SPI to be useful, the user has to add a DT node to represent the SPI
> device itself anyway, so adding some properties to the controller to
> define which GPIOs to use for SPI CS can be done then too.

>From what I have seen (and I am not an expert) is that with the 
foundation device trees each "device" (spi/i2c/...) has a separate
Gpio section, which gets referenced inside the spi/i2c/... block.

As far as I understood with this setup the GPIOs ALT only gets set
up when the driver itself loads (probably while parsing the DT
for the device)

So this is maybe the way forward for the whole default-dt?

For SPI it would look like this:
&gpio {
        spi0_pins: spi0_pins {
                brcm,pins = <7 8 9 10 11>;
                brcm,function = <4>; /* alt0 */
        };
	...
}

&spi0 {
	...
        pinctrl-0 = <&spi0_pins>;
	...
}

And if you keep spi0 disabled in the dtsi files then the ALT
modes should not be set.

Obviously we could also split the gpio-block into 
"normal SPI" and "CS" pins, which would allow changing the
"defaults" also in the dts that gets build.

So how should we proceed?

Martin--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux