No problem. I noticed the changes yesterday afternoon, so they're recent. Mark Peveto Registered Linux user number 600552 Sent from vinux using alpine 2.20.10 On Thu, 26 May 2016, Jude DaShiell wrote: > Once pulseaudio is removed from a machine, running alsactl init should > initialize all sound cards to default values. The pulseaudio-alsa > package has to be deliberately installed on talkingarchlinux at least I > don't know what sonar or manjaro or f123 do. > > On Thu, 26 May 2016, Willem Venter wrote: > > > Date: Thu, 26 May 2016 15:11:00 > > From: Willem Venter <dwillemv@xxxxxxxxx> > > Reply-To: Speakup is a screen review system for Linux. > > <speakup@xxxxxxxxxxxxxxxxx> > > To: Speakup is a screen review system for Linux. <speakup@xxxxxxxxxxxxxxxxx> > > Subject: Re: espeakup > > > > Hi. > > Pulseaudio takes complete control of the audio device, so when other > > devices try to use the soundcard through alsa things break. > > > > A work around I use is playing sound using dmix. This means a bit more > > processing and possibly a little latency for programs using pulse, but > > on the other hand it's better than broken sound. > > > > Remove package pulseaudio-alsa, which provides compatibility layer > > between ALSA applications and PulseAudio. After this your ALSA apps > > will use ALSA directly without being hooked by Pulse. > > Edit /etc/pulse/default.pa. > > Find and uncomment lines which load back-end drivers. Add device > > parameters as follows. Then find and comment lines which load > > autodetect modules. > > load-module module-alsa-sink device=dmix > > load-module module-alsa-source device=dsnoop > > # load-module module-udev-detect > > # load-module module-detect > > > > After rebooting pulseaudio won't grab the sound device, but instead > > plays it through dmix. > > > > hth > > Willem > > > > On 5/26/16, Mark Peveto <southernprince73@xxxxxxxxx> wrote: > >> Here's the error I was talking about earlier. > >> > >> Back story: I'm trying to get console speech. Since i can't right now, > >> I'm doing this from a terminal, which reads badly. Once I type sudo > >> espeakup, it'll read the top of the console screen, and the login prompt > >> asking for a username. After that it gives an error which i'll post. I > >> know it's a pulseaudio problem. Most suggest I get rid of pulseaudio, > >> and if that's the only solution there is, I guess i'll have to, but that > >> creates more problems when it comes to having the system rediscover new > >> sound drivers. Long explanation short, it jacks things up! > >> > >> Error follows. > >> > >> [southernprince@roxie ~]$ sudo espeakup > >> [sudo] password for southernprince: > >> [southernprince@roxie ~]$ Assertion 'p' failed at pulse/simple.c:273, > >> function pa_simple_write(). Aborting. > >> > >> It should be noted here that the error does not appear until I start to > >> type. It reads the login prompt, and once i hit the s for > >> southernprinc, my username, the error appears. If I could figure out > >> how, I might turn keyecho off, which I wanna do anyway, but I don't know > >> if that'd help anything. > >> > >> There ya have it folks. > >> > >> _______________________________________________ > >> Speakup mailing list > >> Speakup@xxxxxxxxxxxxxxxxx > >> http://linux-speakup.org/cgi-bin/mailman/listinfo/speakup > >> > > _______________________________________________ > > Speakup mailing list > > Speakup@xxxxxxxxxxxxxxxxx > > http://linux-speakup.org/cgi-bin/mailman/listinfo/speakup > > -- > > _______________________________________________ > Speakup mailing list > Speakup@xxxxxxxxxxxxxxxxx > http://linux-speakup.org/cgi-bin/mailman/listinfo/speakup > _______________________________________________ Speakup mailing list Speakup@xxxxxxxxxxxxxxxxx http://linux-speakup.org/cgi-bin/mailman/listinfo/speakup
