-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all. A few days ago, someone reported (I believe it was Chuck) that when booting using the speakup.s floppy image in slackware 10, there is no speech, even though the install.1 and install.2 root disks load just fine. I have just verified this observation to be correct. When I boot the speakup.s floppy from slackware 10 with a bns on ttyS0, I get no speech, and the install.1 and install.2 root disks load just fine here as well. However, if I boot with the speakup.s image from slackware 9.1, the bns starts chattering away just fine. Wanting to investigate this further, after the install.2 disk finished loading, I logged in, put another floppy in the system, and made a copy of the dmesg output on that floppy. Before I go on, I want to point out that when speakup.s loaded, at the boot prompt I typed: ramdisk speakup_synth=bns Below is the relevant portion of the dmesg output that I got when booting with the floppies from slackware 10. Linux version 2.4.26 (root at tree) (gcc version 3.3.4) #33 Mon Jun 14 19:26:13 PDT 2004 BIOS-provided physical RAM map: BIOS-e801: 0000000000000000 - 000000000009f000 (usable) BIOS-e801: 0000000000100000 - 0000000003000000 (usable) 48MB LOWMEM available. On node 0 totalpages: 12288 zone(0): 4096 pages. zone(1): 8192 pages. zone(2): 0 pages. DMI not present. Kernel command line: vmlinuz ramdisk_size=7000 root=/dev/fd0u1440 vga=normal rw SLACK_KERNEL=speakup.s Initializing CPU#0 Detected 133.644 MHz processor. Speakup v-2.00 CVS: Mon Jun 7 10:52:38 EDT 2004 : initialized Console: colour VGA+ 80x25 Calibrating delay loop... 266.24 BogoMIPS Memory: 45168k/49152k available (1982k kernel code, 3596k reserved, 673k data, 120k init, 0k highmem) Dentry cache hash table entries: 8192 (order: 4, 65536 bytes) Inode cache hash table entries: 4096 (order: 3, 32768 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 16384 (order: 4, 65536 bytes) initialized device: /dev/synth, node ( MAJOR 10, MINOR 25 ) These are the only mentions of speakup in the entire dmesg output. Also, notice that while I typed: ramdisk speakup_synth=bns at the boot prompt, the dmesg output shown above says: Kernel command line: vmlinuz ramdisk_size=7000 root=/dev/fd0u1440 vga=normal rw SLACK_KERNEL=speakup.s I tried this process twice more, and got the dmesg output twice more, all with the same results. I had a look at the files in the speakup.s images from slackware 9.1, and 10.0, but don't notice any obvious differences, especially when carefully examining syslinux.cfg on both images. Obviously, there is a problem somewhere in the speakup.s image in slackware 10.0, but darned if I know what that problem is. Greg - -- Free domains: http://www.eu.org/ or mail dns-manager at EU.org -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.3 (GNU/Linux) iD8DBQFBDD2N7s9z/XlyUyARAnmnAKCLG68+CJY01Tb8eOKwBB1qSvHaWACfdFih LJnKN8VTNHmiz4oERnc7sus= =KgyK -----END PGP SIGNATURE-----
