Hi Janina. What I ended up doing was writing a start-up script which will run the alias command at boot time, because when I had to reboot to load my new rebuilt kernel, I saw that the alias s had been removed for some reason. Will have to dig around to find out why. ----- Original Message ----- From: Janina Sajka <janina@xxxxxxx> To: <speakup at braille.uwo.ca> Sent: Monday, April 22, 2002 8:59 PM Subject: Re: saving rate > Yes, this will work very well, Igor. > > I started with this kind of alias too. But I soon discovered that I might want to reset my punctuation level, and my > default voice. And, as you suggest, I do have several synths that I might happen to be using. > > The quotes are important, I think. I have never tried without them, in any case. I think of them as identifying a single > entity in the alias--all of the params to the right of the equals sign. > > On Mon, 22 Apr 2002, Igor Gueths wrote: > > > Hi Janina. I know this might be stupid, but I would think you leave the > > quotes in in this case? Normally I wouldn't be asking this, but judging > > from the fact that its a script we're talking about, do the quotes serve > > as identifiers to the command itself, and the ` just means a next-command > > type function? Based on your alias command, I have derived the following. > > Note: Going to leave in quotes for now, bug please correct if wrong. > > > > alias s="echo 350 >/proc/speakup/rate" > > > > In Theory, I would think that the above command aliased to s would > > reset the rate back to 350. The reason I left out copying the values to > > /etc is because I don't have more than one synth (it could be different in > > your case), so I figured I'd just leave it in /proc/speakup. > > > > On Mon, 22 Apr 2002, Janina Sajka wrote: > > > > > No, not saving. You then have to copy those values into /proc/speakup. Let me go get my alias command ... > > > > > > alias s="cp /etc/speakup/`cat /proc/speakup/synth`/* /proc/speakup" > > > s > > > > > > The first of these two defines an alias which I call s. The second calls the alias. This is from my .bash_profile. > > > > > > Thereafter, if my settings go kerflooee, I just issue another s <ENTER> > > > > > > and all is back as it should be. > > > > > > > > > On Mon, 22 Apr 2002, Igor Gueths wrote: > > > > > > > Hi Janina. But does saving the settings you have changed in /etc/ actually > > > > make it so your rate is set to whatever you set it to instead of the > > > > default of 300? > > > > > > > > On Mon, 22 Apr 2002, Janina Sajka wrote: > > > > > > > > > Your correct. The answer is in the speakup archive. > > > > > > > > > > Basically, the best solution seems to be to save the settings to a directory under /etc. My directory is called speakup and I have directories below > > > > > that for each synth I use. These contain the settings I may wish to change on the fly. > > > > > > > > > > Do a search for /etc/speakup in the archive to find the mail on this. > > > > > > > > > > On Mon, 22 Apr 2002, Igor Gueths wrote: > > > > > > > > > > > Hi all. I don't remember if this was talked about before, but in any case > > > > > > I don't remember what the thread (s) were called. Does anyone know how I > > > > > > could save any settings that I made to any parameter in /proc/speakup? I > > > > > > changed the default rate from 300 to 350 fine. However, when I have to > > > > > > reboot let's say for a kernel recompile like the last time I did it, the > > > > > > rate was back at 300. Is there any way to save the current settings? > > > > > > Thanks! > > > > > > > > > > > > > > > > > > _______________________________________________ > > > > > > Speakup mailing list > > > > > > Speakup at braille.uwo.ca > > > > > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > > > > > > > > > > > > > > -- > > > > > > > > > > Janina Sajka, Director > > > > > Technology Research and Development > > > > > Governmental Relations Group > > > > > American Foundation for the Blind (AFB) > > > > > > > > > > Email: janina at afb.net Phone: (202) 408-8175 > > > > > > > > > > Chair, Accessibility SIG > > > > > Open Electronic Book Forum (OEBF) > > > > > http://www.openebook.org > > > > > > > > > > > > > > > _______________________________________________ > > > > > Speakup mailing list > > > > > Speakup at braille.uwo.ca > > > > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > > > > > > > > > > > > > > > _______________________________________________ > > > > Speakup mailing list > > > > Speakup at braille.uwo.ca > > > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > > > > > > > > -- > > > > > > Janina Sajka, Director > > > Technology Research and Development > > > Governmental Relations Group > > > American Foundation for the Blind (AFB) > > > > > > Email: janina at afb.net Phone: (202) 408-8175 > > > > > > Chair, Accessibility SIG > > > Open Electronic Book Forum (OEBF) > > > http://www.openebook.org > > > > > > > > > _______________________________________________ > > > Speakup mailing list > > > Speakup at braille.uwo.ca > > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > > > > > > > _______________________________________________ > > Speakup mailing list > > Speakup at braille.uwo.ca > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > > -- > > Janina Sajka, Director > Technology Research and Development > Governmental Relations Group > American Foundation for the Blind (AFB) > > Email: janina at afb.net Phone: (202) 408-8175 > > Chair, Accessibility SIG > Open Electronic Book Forum (OEBF) > http://www.openebook.org > > > _______________________________________________ > Speakup mailing list > Speakup at braille.uwo.ca > http://speech.braille.uwo.ca/mailman/listinfo/speakup
