There is no /dev/eth0. To see if your card has an interface, do a "ifconfig" That should show you the list of network interfaces. On Sat, 16 Mar 2002, Igor Gueths wrote: > Hi Greg. The driver could be loading at boot time. In fact, it mentions eth0 when it successuflly probes for the card and mac address. However, when I log in and check /dev to make sure that eth0 is in fact there, I get the following: ls: eth0: no such file or directory. Does this mean that the card didn't properly initialize into a device file? How could I fix this? Thanks in advance! > ----- Original Message ----- > From: Gregory Nowak <gnowak1 at uic.edu> > To: <speakup at braille.uwo.ca> > Sent: Saturday, March 16, 2002 11:54 AM > Subject: Re: question > > > > Yes, your driver is in the kernel. Also, based on your previous post that says that the kernel lists all the info about the card, the driver is in fact loading. > > Greg > > > > > > On Sat, Mar 16, 2002 at 10:05:35AM -0500, Igor Gueths wrote: > > > Hi. Well interestingly enough, when I do a lsmod, there are no modules listed. But when the kernel is booting, it tells me the driver version and all the information regarding the card itself such as mac address. So I believe that this means that the driver is in the kernel? I believe this is so, however for some reason the tulip driver might not be loading? > > > ----- Original Message ----- > > > From: Georgina <gena at gena-j.net> > > > To: <speakup at braille.uwo.ca> > > > Sent: Saturday, March 16, 2002 9:56 AM > > > Subject: Re: question > > > > > > > > > > Hi > > > > > > > > Sorry forgot try "man interfaces" > > > > > > > > Gena > > > > > > > > > > > > > > > > >Hi all. I finally got my kernel to boot, and after doing a make = > > > > >oldconfig and editing .config to answer y to tulip support, the kernel = > > > > >boots. It probes my ethernet card and calls it eth0. It also displays = > > > > >its mac address and finds it on irq 10. However, the problem is that = > > > > >when I check dev to make sure eth0 is present, it isn't there. Why would = > > > > >the device not be initialized into a device file if it was probed = > > > > >successfully? This doesn't really make sense to me, considering that = > > > > >everything went ok. And naturally, I couldn't do ifconfig dhcp because = > > > > >it didn't find the network interface? How could I go about fixing this = > > > > >problem? Thanks in advance!=20 > > > > > > > > > > > > > > >_________________________________________________________ > > > > >Do You Yahoo!? > > > > >Get your free @yahoo.com address at http://mail.yahoo.com > > > > > > > > > > > > > > >_______________________________________________ > > > > >Speakup mailing list > > > > >Speakup at braille.uwo.ca > > > > >http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > > > > > > _______________________________________________ > > > > Speakup mailing list > > > > Speakup at braille.uwo.ca > > > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > > > > > > > _________________________________________________________ > > > Do You Yahoo!? > > > Get your free @yahoo.com address at http://mail.yahoo.com > > > > > > > > > _______________________________________________ > > > Speakup mailing list > > > Speakup at braille.uwo.ca > > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > > _______________________________________________ > > Speakup mailing list > > Speakup at braille.uwo.ca > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > _________________________________________________________ > Do You Yahoo!? > Get your free @yahoo.com address at http://mail.yahoo.com > > > _______________________________________________ > Speakup mailing list > Speakup at braille.uwo.ca > http://speech.braille.uwo.ca/mailman/listinfo/speakup >
