We've earlier added support to split the register address space into TM
and SROT regions.
Split up the regmap address space into two for the remaining platforms
that have a similar register layout and make corresponding changes to
the get_temp_common() function used by these platforms.
Since tsens-common.c/init_common() currently only registers one address
space, the order is important (TM before SROT). This is OK since the
code doesn't really use the SROT functionality yet.
Signed-off-by: Amit Kucheria <amit.kucheria@xxxxxxxxxx>
Reviewed-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
---
arch/arm/boot/dts/qcom-msm8974.dtsi | 5 +++--
arch/arm64/boot/dts/qcom/msm8916.dtsi | 5 +++--
drivers/thermal/qcom/tsens-common.c | 5 +++--
3 files changed, 9 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index d9019a49b292..56dbbf788d15 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -427,9 +427,10 @@
};
};
- tsens: thermal-sensor@fc4a8000 {
+ tsens: thermal-sensor@fc4a9000 {
compatible = "qcom,msm8974-tsens";
- reg = <0xfc4a8000 0x2000>;
+ reg = <0xfc4a9000 0x1000>, /* TM */
+ <0xfc4a8000 0x1000>; /* SROT */
nvmem-cells = <&tsens_calib>, <&tsens_backup>;
nvmem-cell-names = "calib", "calib_backup";
#thermal-sensor-cells = <1>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 7b32b8990d62..6a277fce3333 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -761,9 +761,10 @@
};
};
- tsens: thermal-sensor@4a8000 {
+ tsens: thermal-sensor@4a9000 {
compatible = "qcom,msm8916-tsens";
- reg = <0x4a8000 0x2000>;
+ reg = <0x4a9000 0x1000>, /* TM */
+ <0x4a8000 0x1000>; /* SROT */
nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
nvmem-cell-names = "calib", "calib_sel";
#thermal-sensor-cells = <1>;
diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index 6207d8d92351..478739543bbc 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -21,7 +21,7 @@
#include <linux/regmap.h>
#include "tsens.h"
-#define S0_ST_ADDR 0x1030
+#define STATUS_OFFSET 0x30
#define SN_ADDR_OFFSET 0x4
#define SN_ST_TEMP_MASK 0x3ff
#define CAL_DEGC_PT1 30
@@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
unsigned int status_reg;
int last_temp = 0, ret;
- status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
+ status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
ret = regmap_read(tmdev->map, status_reg, &code);
+
if (ret)
return ret;
last_temp = code & SN_ST_TEMP_MASK;
--
2.17.1
