When the temperature reaches stage 2 the PMIC performs by default a
'partial shutdown', unless software override is enabled. It is not well
defined which peripherals are affected by a 'partial shutdown'. Drivers
might be unhappy when their devices suddenly disappear and prevent an
orderly shutdown.
Add an optional device tree property that allows to disable stage 2
shutdown.
Signed-off-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
---
Changes in v4:
- patch added to the series
---
.../bindings/thermal/qcom-spmi-temp-alarm.txt | 3 ++
drivers/thermal/qcom-spmi-temp-alarm.c | 28 +++++++++++++------
2 files changed, 23 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt b/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt
index 290ec06fa33a..377c94fa1821 100644
--- a/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt
+++ b/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt
@@ -15,6 +15,8 @@ Optional properties:
- io-channels: Should contain IIO channel specifier for the ADC channel,
which report chip die temperature.
- io-channel-names: Should contain "thermal".
+- stage2-shutdown-disabled: boolean to disable a partial shutdown of the PMIC
+ when the temperature reaches stage 2
Example:
@@ -23,6 +25,7 @@ Example:
reg = <0x2400 0x100>;
interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
#thermal-sensor-cells = <0>;
+ stage2-shutdown-disabled;
io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
io-channel-names = "thermal";
diff --git a/drivers/thermal/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom-spmi-temp-alarm.c
index ad4f3a8d6560..acbb0dbec79e 100644
--- a/drivers/thermal/qcom-spmi-temp-alarm.c
+++ b/drivers/thermal/qcom-spmi-temp-alarm.c
@@ -37,7 +37,9 @@
#define STATUS_GEN2_STATE_MASK GENMASK(6, 4)
#define STATUS_GEN2_STATE_SHIFT 4
-#define SHUTDOWN_CTRL1_OVERRIDE_MASK GENMASK(7, 6)
+#define SHUTDOWN_CTRL1_OVERRIDE_S2 BIT(6)
+#define SHUTDOWN_CTRL1_OVERRIDE_S2_MASK GENMASK(6, 6)
+#define SHUTDOWN_CTRL1_OVERRIDE_S3_MASK GENMASK(7, 7)
#define SHUTDOWN_CTRL1_THRESHOLD_MASK GENMASK(1, 0)
#define ALARM_CTRL_FORCE_ENABLE BIT(7)
@@ -198,7 +200,8 @@ static irqreturn_t qpnp_tm_isr(int irq, void *data)
* current thermal stage and threshold. Setup threshold control and
* disable shutdown override.
*/
-static int qpnp_tm_init(struct qpnp_tm_chip *chip)
+static int qpnp_tm_init(struct qpnp_tm_chip *chip,
+ bool disable_stage2_shutdown)
{
unsigned int stage;
int ret;
@@ -224,13 +227,18 @@ static int qpnp_tm_init(struct qpnp_tm_chip *chip)
(stage - 1) * TEMP_STAGE_STEP +
TEMP_THRESH_MIN;
- /*
- * Set threshold and disable software override of stage 2 and 3
- * shutdowns.
- */
+ /* Set threshold and disable software override of stage 3 shutdown. */
chip->thresh = THRESH_MIN;
- reg &= ~(SHUTDOWN_CTRL1_OVERRIDE_MASK | SHUTDOWN_CTRL1_THRESHOLD_MASK);
+ reg &= ~(SHUTDOWN_CTRL1_OVERRIDE_S3_MASK |
+ SHUTDOWN_CTRL1_THRESHOLD_MASK);
reg |= chip->thresh & SHUTDOWN_CTRL1_THRESHOLD_MASK;
+
+ /* Disable stage 2 shutdown if requested */
+ if (disable_stage2_shutdown)
+ reg |= SHUTDOWN_CTRL1_OVERRIDE_S2;
+ else
+ reg &= ~SHUTDOWN_CTRL1_OVERRIDE_S2_MASK;
+
ret = qpnp_tm_write(chip, QPNP_TM_REG_SHUTDOWN_CTRL1, reg);
if (ret < 0)
return ret;
@@ -248,6 +256,7 @@ static int qpnp_tm_probe(struct platform_device *pdev)
struct device_node *node;
u8 type, subtype;
u32 res;
+ bool stage2_shutdown_disabled;
int ret, irq;
node = pdev->dev.of_node;
@@ -302,7 +311,10 @@ static int qpnp_tm_probe(struct platform_device *pdev)
chip->subtype = subtype;
- ret = qpnp_tm_init(chip);
+ stage2_shutdown_disabled = of_property_read_bool(node,
+ "stage2-shutdown-disabled");
+
+ ret = qpnp_tm_init(chip, stage2_shutdown_disabled);
if (ret < 0) {
dev_err(&pdev->dev, "init failed\n");
return ret;
--
2.18.0.203.gfac676dfb9-goog
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
