q6v5-wcss core's start function is mostly common
with the q6v5 of msm8996. So reuse that and add
the stop function.
Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
---
drivers/remoteproc/qcom_q6v5_pil.c | 227 +++++++++++++++++++++++++++++++++++++
1 file changed, 227 insertions(+)
diff --git a/drivers/remoteproc/qcom_q6v5_pil.c b/drivers/remoteproc/qcom_q6v5_pil.c
index fbe179d..979f6c9 100644
--- a/drivers/remoteproc/qcom_q6v5_pil.c
+++ b/drivers/remoteproc/qcom_q6v5_pil.c
@@ -113,6 +113,17 @@
#define SLEEP_CHECK_MAX_LOOPS 200
#define BOOT_FSM_TIMEOUT 10000
+/* QDSP6v5-WCSS config/status registers */
+#define TCSR_GLOBAL_CFG0 0x0
+#define TCSR_GLOBAL_CFG1 0x4
+#define SSCAON_CONFIG 0x8
+#define SSCAON_STATUS 0xc
+#define QDSP6SS_BHS_STATUS 0x78
+#define QDSP6SS_RST_EVB 0x10
+
+#define BHS_EN_REST_ACK BIT(0)
+#define SSCAON_ENABLE BIT(13)
+
struct reg_info {
struct regulator *reg;
int uV;
@@ -823,6 +834,61 @@ static int q6v5_mpss_load(struct q6v5 *qproc)
return ret < 0 ? ret : 0;
}
+static int q6v5_wcss_start(struct rproc *rproc)
+{
+ struct q6v5 *qproc = rproc->priv;
+ int ret = 0;
+
+ ret = q6v5_clk_enable(qproc->dev, qproc->active_clks,
+ qproc->active_clk_count);
+ if (ret) {
+ dev_err(qproc->dev, "failed to enable clocks\n");
+ return ret;
+ }
+
+ /* Release Q6 and WCSS reset */
+ ret = reset_control_deassert(qproc->wcss_reset);
+ if (ret)
+ dev_err(qproc->dev, "wcss_reset failed\n");
+
+ ret = reset_control_deassert(qproc->wcss_q6_reset);
+ if (ret)
+ dev_err(qproc->dev, "wcss_q6_reset failed\n");
+
+ /* Lithium configuration - clock gating and bus arbitration */
+ ret = regmap_update_bits(qproc->halt_map,
+ qproc->halt_nc + TCSR_GLOBAL_CFG0,
+ 0x1F, 0x14);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(qproc->halt_map,
+ qproc->halt_nc + TCSR_GLOBAL_CFG1,
+ 1, 0);
+ if (ret)
+ return ret;
+
+ /* Write bootaddr to EVB so that Q6WCSS will jump there after reset */
+ writel(rproc->bootaddr >> 4, qproc->reg_base + QDSP6SS_RST_EVB);
+
+ ret = q6v5_reset(qproc);
+ if (ret)
+ return ret;
+
+ q6v5_reset_rest(qproc);
+
+ ret = wait_for_completion_timeout(&qproc->start_done,
+ msecs_to_jiffies(5000));
+ if (ret == 0) {
+ dev_err(qproc->dev, "start timed out\n");
+ return -ETIMEDOUT;
+ }
+
+ qproc->running = true;
+
+ return 0;
+}
+
static int q6v5_start(struct rproc *rproc)
{
struct q6v5 *qproc = (struct q6v5 *)rproc->priv;
@@ -972,6 +1038,149 @@ static int q6v5_start(struct rproc *rproc)
return ret;
}
+static int q6v5_wcss_powerdown(struct q6v5 *qproc)
+{
+ unsigned int val = 0;
+ int ret;
+
+ /* 1 - Assert WCSS/Q6 HALTREQ */
+ q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem);
+
+ /* 2 - Enable WCSSAON_CONFIG */
+ val = readl(qproc->rmb_base + SSCAON_CONFIG);
+ val |= SSCAON_ENABLE;
+ writel(val, qproc->rmb_base + SSCAON_CONFIG);
+
+ /* 3 - Set SSCAON_CONFIG */
+ val |= BIT(15);
+ val &= ~BIT(16);
+ val &= ~BIT(17);
+ val &= ~BIT(18);
+ writel(val, qproc->rmb_base + SSCAON_CONFIG);
+
+ /* 4 - SSCAON_CONFIG 1 */
+ val |= BIT(1);
+ writel(val, qproc->rmb_base + SSCAON_CONFIG);
+
+ /* 5 - wait for SSCAON_STATUS */
+ ret = readl_poll_timeout(qproc->rmb_base + SSCAON_STATUS,
+ val, (val & 0xffff) == 0x400, 1000,
+ HALT_CHECK_MAX_LOOPS);
+ if (ret) {
+ dev_err(qproc->dev,
+ "can't get SSCAON_STATUS rc:%d)\n", ret);
+ }
+
+ /* 6 - De-assert WCSS_AON reset */
+ reset_control_assert(qproc->wcss_aon_reset);
+
+ /* 7 - Disable WCSSAON_CONFIG 13 */
+ val = readl(qproc->rmb_base + SSCAON_CONFIG);
+ val &= ~SSCAON_ENABLE;
+ writel(val, qproc->rmb_base + SSCAON_CONFIG);
+
+ /* 8 - De-assert WCSS/Q6 HALTREQ */
+ reset_control_assert(qproc->wcss_reset);
+
+ return ret;
+}
+
+static int q6v5_q6_powerdown(struct q6v5 *qproc)
+{
+ int i = 0, ret;
+ unsigned int val = 0;
+
+ /* 1 - Halt Q6 bus interface */
+ q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_q6);
+
+ /* 2 - Disable Q6 Core clock */
+ val = readl(qproc->reg_base + QDSP6SS_GFMUX_CTL_REG);
+ val &= ~Q6SS_CLK_ENABLE;
+ writel(val, qproc->reg_base + QDSP6SS_GFMUX_CTL_REG);
+
+ /* 3 - Clamp I/O */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= Q6SS_CLAMP_IO;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* 4 - Clamp WL */
+ val |= QDSS_BHS_ON;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* 5 - Clear Erase standby */
+ val &= ~Q6SS_L2DATA_STBY_N;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* 6 - Clear Sleep RTN */
+ val &= ~Q6SS_SLP_RET_N;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* 7 - turn off QDSP6 memory foot/head switch one bank at a time */
+ for (i = 0; i < 20; i++) {
+ val = readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL);
+ val &= ~BIT(i);
+ writel(val, qproc->reg_base + QDSP6SS_MEM_PWR_CTL);
+ mdelay(1);
+ }
+ /* 8 - Assert QMC memory RTN */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= QDSP6v56_CLAMP_QMC_MEM;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* 9 - Turn off BHS */
+ val &= ~QDSP6v56_BHS_ON;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ udelay(1);
+ /* 10 - Wait till BHS Reset is done */
+ ret = readl_poll_timeout(qproc->reg_base + QDSP6SS_BHS_STATUS,
+ val, !(val & BHS_EN_REST_ACK), 1000,
+ HALT_CHECK_MAX_LOOPS);
+ if (ret) {
+ dev_err(qproc->dev,
+ "BHS_STATUS not OFF (rc:%d)\n", ret);
+ }
+
+ /* 11 - Assert WCSS reset */
+ reset_control_assert(qproc->wcss_reset);
+
+ /* 12 - Assert Q6 reset */
+ reset_control_assert(qproc->wcss_q6_reset);
+
+ return 0;
+}
+
+static int q6v5_wcss_stop(struct rproc *rproc)
+{
+ struct q6v5 *qproc = rproc->priv;
+ int ret = 0;
+
+ qproc->running = false;
+
+ /* WCSS powerdown */
+ qcom_smem_state_update_bits(qproc->state, BIT(qproc->stop_bit),
+ BIT(qproc->stop_bit));
+
+ ret = wait_for_completion_timeout(&qproc->stop_done,
+ msecs_to_jiffies(5000));
+ if (ret == 0) {
+ dev_err(qproc->dev, "timed out on wait\n");
+ return -ETIMEDOUT;
+ }
+
+ qcom_smem_state_update_bits(qproc->state, BIT(qproc->stop_bit), 0);
+
+ ret = q6v5_wcss_powerdown(qproc);
+ if (ret)
+ return ret;
+
+ /* Q6 Power down */
+ ret = q6v5_q6_powerdown(qproc);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
static int q6v5_stop(struct rproc *rproc)
{
struct q6v5 *qproc = (struct q6v5 *)rproc->priv;
@@ -1041,6 +1250,15 @@ static void *q6v5_da_to_va(struct rproc *rproc, u64 da, int len)
return qproc->mpss_region + offset;
}
+static int q6v5_wcss_load(struct rproc *rproc, const struct firmware *fw)
+{
+ struct q6v5 *qproc = rproc->priv;
+
+ return qcom_mdt_load_no_init(qproc->dev, fw, rproc->firmware,
+ 0, qproc->mba_region, qproc->mba_phys,
+ qproc->mba_size, &qproc->mpss_reloc);
+}
+
static const struct rproc_ops q6v5_ops = {
.start = q6v5_start,
.stop = q6v5_stop,
@@ -1048,6 +1266,14 @@ static void *q6v5_da_to_va(struct rproc *rproc, u64 da, int len)
.load = q6v5_load,
};
+static const struct rproc_ops q6v5_wcss_ops = {
+ .start = q6v5_wcss_start,
+ .stop = q6v5_wcss_stop,
+ .da_to_va = q6v5_da_to_va,
+ .load = q6v5_wcss_load,
+ .get_boot_addr = rproc_elf_get_boot_addr,
+};
+
static irqreturn_t q6v5_wdog_interrupt(int irq, void *dev)
{
struct q6v5 *qproc = dev;
@@ -1569,6 +1795,7 @@ static int q6v5_remove(struct platform_device *pdev)
.need_mem_protection = false,
.version = WCSS_IPQ8074,
.init_reset = q6v5_wcss_init_reset,
+ .ops = &q6v5_wcss_ops,
};
static const struct of_device_id q6v5_of_match[] = {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
