Re: [PATCH 11/12] i2c: qup: reorganization of driver code to remove polling for qup v1

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2018-02-16 13:14, Sricharan R wrote:
Hi Abhishek,

On 2/3/2018 1:28 PM, Abhishek Sahu wrote:
Following are the major issues in current driver code

1. The current driver simply assumes the transfer completion
   whenever its gets any non-error interrupts and then simply do the
   polling of available/free bytes in FIFO.
2. The block mode is not working properly since no handling in
   being done for OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ.

Because of above, i2c v1 transfers of size greater than 32 are failing
with following error message

	i2c_qup 78b6000.i2c: timeout for fifo out full

To make block mode working properly and move to use the interrupts
instead of polling, major code reorganization is required. Following
are the major changes done in this patch

1. Remove the polling of TX FIFO free space and RX FIFO available
bytes and move to interrupts completely. QUP has QUP_MX_OUTPUT_DONE,
   QUP_MX_INPUT_DONE, OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ
   interrupts to handle FIFO’s properly so check all these interrupts.
2. During write, For FIFO mode, TX FIFO can be directly written
without checking for FIFO space. For block mode, the QUP will generate OUT_BLOCK_WRITE_REQ interrupt whenever it has block size of available
   space.
3. During read, both TX and RX FIFO will be used. TX will be used
for writing tags and RX will be used for receiving the data. In QUP, TX and RX can operate in separate mode so configure modes accordingly.
4. For read FIFO mode, wait for QUP_MX_INPUT_DONE interrupt which
will be generated after all the bytes have been copied in RX FIFO. For
   read Block mode, QUP will generate IN_BLOCK_READ_REQ interrupts
   whenever it has block size of available data.

Signed-off-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
---
drivers/i2c/busses/i2c-qup.c | 399 ++++++++++++++++++++++++++++---------------
 1 file changed, 257 insertions(+), 142 deletions(-)

diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c
index edea3b9..af6c21a 100644
--- a/drivers/i2c/busses/i2c-qup.c
+++ b/drivers/i2c/busses/i2c-qup.c
@@ -73,8 +73,11 @@
 #define QUP_IN_SVC_FLAG		BIT(9)
 #define QUP_MX_OUTPUT_DONE	BIT(10)
 #define QUP_MX_INPUT_DONE	BIT(11)
+#define OUT_BLOCK_WRITE_REQ	BIT(12)
+#define IN_BLOCK_READ_REQ	BIT(13)

 /* I2C mini core related values */
+#define QUP_NO_INPUT		BIT(7)
 #define QUP_CLOCK_AUTO_GATE	BIT(13)
 #define I2C_MINI_CORE		(2 << 8)
 #define I2C_N_VAL		15
@@ -138,13 +141,51 @@
 #define DEFAULT_CLK_FREQ 100000
 #define DEFAULT_SRC_CLK 20000000

+/* MAX_OUTPUT_DONE_FLAG has been received */
+#define QUP_BLK_EVENT_TX_IRQ_DONE		BIT(0)
+/* MAX_INPUT_DONE_FLAG has been received */
+#define QUP_BLK_EVENT_RX_IRQ_DONE		BIT(1)
+/* All the TX bytes have been written in TX FIFO */
+#define QUP_BLK_EVENT_TX_DATA_DONE		BIT(2)
+/* All the RX bytes have been read from RX FIFO */
+#define QUP_BLK_EVENT_RX_DATA_DONE		BIT(3)
+
+/* All the required events to mark a QUP I2C TX transfer completed */
+#define QUP_BLK_EVENT_TX_DONE		(QUP_BLK_EVENT_TX_IRQ_DONE | \
+					 QUP_BLK_EVENT_TX_DATA_DONE)
+/* All the required events to mark a QUP I2C RX transfer completed */
+#define QUP_BLK_EVENT_RX_DONE		(QUP_BLK_EVENT_TX_DONE | \
+					 QUP_BLK_EVENT_RX_IRQ_DONE | \
+					 QUP_BLK_EVENT_RX_DATA_DONE)
+
+/*
+ * count: no of blocks
+ * pos: current block number
+ * tx_tag_len: tx tag length for current block
+ * rx_tag_len: rx tag length for current block
+ * data_len: remaining data length for current message
+ * total_tx_len: total tx length including tag bytes for current QUP transfer + * total_rx_len: total rx length including tag bytes for current QUP transfer
+ * tx_fifo_free: number of free bytes in current QUP block write.
+ * fifo_available: number of available bytes in RX FIFO for current
+ *		   QUP block read
+ * is_tx_blk_mode: whether tx uses block or FIFO mode in case of non BAM xfer. + * is_rx_blk_mode: whether rx uses block or FIFO mode in case of non BAM xfer.
+ * tags: contains tx tag bytes for current QUP transfer
+ */
 struct qup_i2c_block {
-	int	count;
-	int	pos;
-	int	tx_tag_len;
-	int	rx_tag_len;
-	int	data_len;
-	u8	tags[6];
+	int		count;
+	int		pos;
+	int		tx_tag_len;
+	int		rx_tag_len;
+	int		data_len;
+	int		total_tx_len;
+	int		total_rx_len;
+	int		tx_fifo_free;
+	int		fifo_available;
+	bool		is_tx_blk_mode;
+	bool		is_rx_blk_mode;
+	u8		tags[6];
 };

 struct qup_i2c_tag {
@@ -187,6 +228,7 @@ struct qup_i2c_dev {

 	/* To check if this is the last msg */
 	bool			is_last;
+	bool			is_qup_v1;

 	/* To configure when bus is in run state */
 	int			config_run;
@@ -195,6 +237,10 @@ struct qup_i2c_dev {
 	bool			is_dma;
 	/* To check if the current transfer is using DMA */
 	bool			use_dma;
+	/* Required events to mark QUP transfer as completed */
+	u32			blk_events;
+	/* Already completed events in QUP transfer */
+	u32			cur_blk_events;
 	/* The threshold length above which DMA will be used */
 	unsigned int		dma_threshold;
 	unsigned int		max_xfer_sg_len;
@@ -205,11 +251,18 @@ struct qup_i2c_dev {
 	struct			qup_i2c_bam btx;

 	struct completion	xfer;
+	/* function to write data in tx fifo */
+	void (*write_tx_fifo)(struct qup_i2c_dev *qup);
+	/* function to read data from rx fifo */
+	void (*read_rx_fifo)(struct qup_i2c_dev *qup);
+	/* function to write tags in tx fifo for i2c read transfer */
+	void (*write_rx_tags)(struct qup_i2c_dev *qup);
 };

 static irqreturn_t qup_i2c_interrupt(int irq, void *dev)
 {
 	struct qup_i2c_dev *qup = dev;
+	struct qup_i2c_block *blk = &qup->blk;
 	u32 bus_err;
 	u32 qup_err;
 	u32 opflags;
@@ -256,12 +309,54 @@ static irqreturn_t qup_i2c_interrupt(int irq, void *dev)
 		goto done;
 	}

-	if (opflags & QUP_IN_SVC_FLAG)
-		writel(QUP_IN_SVC_FLAG, qup->base + QUP_OPERATIONAL);
+	if (!qup->is_qup_v1)
+		goto done;

-	if (opflags & QUP_OUT_SVC_FLAG)
+	if (opflags & QUP_OUT_SVC_FLAG) {
 		writel(QUP_OUT_SVC_FLAG, qup->base + QUP_OPERATIONAL);

+		/*
+		 * Ideally, would like to check QUP_MAX_OUTPUT_DONE_FLAG.
+		 * However, QUP_MAX_OUTPUT_DONE_FLAG is lagging behind
+		 * QUP_OUTPUT_SERVICE_FLAG. The only reason for
+		 * QUP_OUTPUT_SERVICE_FLAG to be set in FIFO mode is
+		 * QUP_MAX_OUTPUT_DONE_FLAG condition. The code checking
+		 * here QUP_OUTPUT_SERVICE_FLAG and assumes that
+		 * QUP_MAX_OUTPUT_DONE_FLAG.
+		 */
+		if (!blk->is_tx_blk_mode)
+			qup->cur_blk_events |= QUP_BLK_EVENT_TX_IRQ_DONE;
+
+		if (opflags & OUT_BLOCK_WRITE_REQ) {
+			blk->tx_fifo_free += qup->out_blk_sz;
+			if (qup->msg->flags & I2C_M_RD)
+				qup->write_rx_tags(qup);
+			else
+				qup->write_tx_fifo(qup);
+		}
+	}
+
+	if (opflags & QUP_IN_SVC_FLAG) {
+		writel(QUP_IN_SVC_FLAG, qup->base + QUP_OPERATIONAL);
+
+		if (!blk->is_rx_blk_mode) {
+			blk->fifo_available += qup->in_fifo_sz;
+			qup->read_rx_fifo(qup);
+		} else if (opflags & IN_BLOCK_READ_REQ) {
+			blk->fifo_available += qup->in_blk_sz;
+			qup->read_rx_fifo(qup);
+		}
+	}
+
+	if (opflags & QUP_MX_OUTPUT_DONE)
+		qup->cur_blk_events |= QUP_BLK_EVENT_TX_IRQ_DONE;
+
+	if (opflags & QUP_MX_INPUT_DONE)
+		qup->cur_blk_events |= QUP_BLK_EVENT_RX_IRQ_DONE;
+
+	if (qup->cur_blk_events != qup->blk_events)
+		return IRQ_HANDLED;

  Is it correct that if we do a complete in above case, i mean
  for TX -> based on QUP_MX_OUTPUT_DONE and for RX -> based on
  QUP_MX_INPUT_DONE, would that simplify things by getting rid of
  QUP_BLK_EVENT_RX/TX_DONE and QUP_BLK_EVENT_RX/TX_IRQ_DONE
  altogether ?

 We can get rid of QUP_BLK_EVENT_TX_DONE.
 For RX, the QUP_MX_INPUT_DONE will be triggered when QUP copies all
 the data in FIFO from external i2c slave. So if 64 bytes read has been
 scheduled then  following is the behaviour

 IRQ with QUP_MX_INPUT_DONE and IN_BLOCK_READ_REQ -> read 16 bytes
 IRQ with IN_BLOCK_READ_REQ -> read next 16 bytes
 IRQ with IN_BLOCK_READ_REQ  -> read next 16 bytes
 IRQ with IN_BLOCK_READ_REQ -> read last 16 bytes

So for RX, we can't trigger complete by checking QUP_BLK_EVENT_RX_DONE alone.
 We need to track the number of bytes read from FIFO. Instead of putting
 this check, I am taking one extra event bit QUP_BLK_EVENT_RX_DONE which
 will be set when all the bytes has been read.

 I am not sure if checking QUP_MX_INPUT_DONE will always work since
 there may be some case, when for small transfers the QUP_MX_INPUT_DONE
 will come before QUP_MX_OUTPUT_DONE so checking for both will work
 always.

 Thanks,
 Abhishek
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Samsung SoC]     [Linux Rockchip SoC]     [Linux Actions SoC]     [Linux for Synopsys ARC Processors]     [Linux NFS]     [Linux NILFS]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]


  Powered by Linux