Implement the callbacks required for an NBCON console [0] on the amba-pl011 console driver. Referred to the NBCON implementation work for 8250 [1] and imx [2]. The normal-priority write_thread checks for console ownership each time a character is printed. write_atomic holds the console ownership until the entire string is printed. UART register operations are protected from other contexts by uart_port_lock, except for a final flush(nbcon_atomic_flush_unsafe) on panic. The patch has been verified to correctly handle the output and competition of messages with different priorities and flushing panic message to console after nmi panic using ARM64 QEMU and a physical machine(A64FX). [0] https://lore.kernel.org/all/ZuRRTbapH0DCj334@xxxxxxxxxxxxxxx/ [1] https://lore.kernel.org/all/20240913140538.221708-1-john.ogness@xxxxxxxxxxxxx/T/ [2] https://lore.kernel.org/linux-arm-kernel/20240913-serial-imx-nbcon-v3-1-4c627302335b@xxxxxxxxxx/T/ Signed-off-by: Toshiyuki Sato <fj6611ie@xxxxxxxxxxxxxxxxx> --- This patch removes the legacy console code. Please comment if you have any concerns. I plan to try a stress test, referencing the work for 8250. https://lore.kernel.org/lkml/ZsdoD6PomBRsB-ow@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx/#t Changes in v2: - Remove the module parameter used to switch between legacy and nbcon. - Remove codes for legacy console. - Fix build errors detected by the test robot. - based on 6.13-rc7 v1: https://lore.kernel.org/all/20250108004730.2302996-1-fj6611ie@xxxxxxxxxxxxxxxxx/ Thanks Greg for the advice & comment. --- drivers/tty/serial/amba-pl011.c | 143 ++++++++++++++++++++++---------- 1 file changed, 97 insertions(+), 46 deletions(-) diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 69b7a3e1e..577fd3258 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -263,6 +263,7 @@ struct uart_amba_port { char type[12]; bool rs485_tx_started; unsigned int rs485_tx_drain_interval; /* usecs */ + bool console_line_ended; #ifdef CONFIG_DMA_ENGINE /* DMA stuff */ unsigned int dmacr; /* dma control reg */ @@ -2305,50 +2306,7 @@ static void pl011_console_putchar(struct uart_port *port, unsigned char ch) while (pl011_read(uap, REG_FR) & UART01x_FR_TXFF) cpu_relax(); pl011_write(ch, uap, REG_DR); -} - -static void -pl011_console_write(struct console *co, const char *s, unsigned int count) -{ - struct uart_amba_port *uap = amba_ports[co->index]; - unsigned int old_cr = 0, new_cr; - unsigned long flags; - int locked = 1; - - clk_enable(uap->clk); - - if (oops_in_progress) - locked = uart_port_trylock_irqsave(&uap->port, &flags); - else - uart_port_lock_irqsave(&uap->port, &flags); - - /* - * First save the CR then disable the interrupts - */ - if (!uap->vendor->always_enabled) { - old_cr = pl011_read(uap, REG_CR); - new_cr = old_cr & ~UART011_CR_CTSEN; - new_cr |= UART01x_CR_UARTEN | UART011_CR_TXE; - pl011_write(new_cr, uap, REG_CR); - } - - uart_console_write(&uap->port, s, count, pl011_console_putchar); - - /* - * Finally, wait for transmitter to become empty and restore the - * TCR. Allow feature register bits to be inverted to work around - * errata. - */ - while ((pl011_read(uap, REG_FR) ^ uap->vendor->inv_fr) - & uap->vendor->fr_busy) - cpu_relax(); - if (!uap->vendor->always_enabled) - pl011_write(old_cr, uap, REG_CR); - - if (locked) - uart_port_unlock_irqrestore(&uap->port, flags); - - clk_disable(uap->clk); + uap->console_line_ended = (ch == '\n'); } static void pl011_console_get_options(struct uart_amba_port *uap, int *baud, @@ -2411,6 +2369,8 @@ static int pl011_console_setup(struct console *co, char *options) if (ret) return ret; + uap->console_line_ended = true; + if (dev_get_platdata(uap->port.dev)) { struct amba_pl011_data *plat; @@ -2494,14 +2454,105 @@ static int pl011_console_match(struct console *co, char *name, int idx, return -ENODEV; } +static void +pl011_console_write_atomic(struct console *co, struct nbcon_write_context *wctxt) +{ + struct uart_amba_port *uap = amba_ports[co->index]; + unsigned int old_cr = 0; + + if (!nbcon_enter_unsafe(wctxt)) + return; + + clk_enable(uap->clk); + + if (!uap->vendor->always_enabled) { + old_cr = pl011_read(uap, REG_CR); + pl011_write((old_cr & ~UART011_CR_CTSEN) | (UART01x_CR_UARTEN | UART011_CR_TXE), + uap, REG_CR); + } + + if (!uap->console_line_ended) + uart_console_write(&uap->port, "\n", 1, pl011_console_putchar); + uart_console_write(&uap->port, wctxt->outbuf, wctxt->len, pl011_console_putchar); + + while ((pl011_read(uap, REG_FR) ^ uap->vendor->inv_fr) & uap->vendor->fr_busy) + cpu_relax(); + + if (!uap->vendor->always_enabled) + pl011_write(old_cr, uap, REG_CR); + + clk_disable(uap->clk); + + nbcon_exit_unsafe(wctxt); +} + +static void +pl011_console_write_thread(struct console *co, struct nbcon_write_context *wctxt) +{ + struct uart_amba_port *uap = amba_ports[co->index]; + unsigned int old_cr = 0; + + if (!nbcon_enter_unsafe(wctxt)) + return; + + clk_enable(uap->clk); + + if (!uap->vendor->always_enabled) { + old_cr = pl011_read(uap, REG_CR); + pl011_write((old_cr & ~UART011_CR_CTSEN) | (UART01x_CR_UARTEN | UART011_CR_TXE), + uap, REG_CR); + } + + if (nbcon_exit_unsafe(wctxt)) { + int i; + unsigned int len = READ_ONCE(wctxt->len); + + for (i = 0; i < len; i++) { + if (!nbcon_enter_unsafe(wctxt)) + break; + uart_console_write(&uap->port, wctxt->outbuf + i, 1, pl011_console_putchar); + if (!nbcon_exit_unsafe(wctxt)) + break; + } + } + + while (!nbcon_enter_unsafe(wctxt)) + nbcon_reacquire_nobuf(wctxt); + + while ((pl011_read(uap, REG_FR) ^ uap->vendor->inv_fr) & uap->vendor->fr_busy) + cpu_relax(); + + if (!uap->vendor->always_enabled) + pl011_write(old_cr, uap, REG_CR); + + clk_disable(uap->clk); + + nbcon_exit_unsafe(wctxt); +} + +static void +pl011_console_device_lock(struct console *co, unsigned long *flags) +{ + __uart_port_lock_irqsave(&amba_ports[co->index]->port, flags); +} + +static void +pl011_console_device_unlock(struct console *co, unsigned long flags) +{ + __uart_port_unlock_irqrestore(&amba_ports[co->index]->port, flags); +} + static struct uart_driver amba_reg; static struct console amba_console = { .name = "ttyAMA", - .write = pl011_console_write, .device = uart_console_device, .setup = pl011_console_setup, .match = pl011_console_match, - .flags = CON_PRINTBUFFER | CON_ANYTIME, + .write_atomic = pl011_console_write_atomic, + .write_thread = pl011_console_write_thread, + .device_lock = pl011_console_device_lock, + .device_unlock = pl011_console_device_unlock, + .flags = CON_PRINTBUFFER | CON_ANYTIME | CON_NBCON, .index = -1, .data = &amba_reg, }; -- 2.34.1
